| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Tue, 19 Jan 2021 21:55:18 +0100
From: Marek Vasut <marex@...x.de>
To: netdev@...r.kernel.org
Cc: Marek Vasut <marex@...x.de>, Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Michael Grzeschik <m.grzeschik@...gutronix.de>,
Jakub Kicinski <kuba@...nel.org>
Subject: [PATCH net-next] net: dsa: microchip: ksz8795: Fix KSZ8794 port map again
The KSZ8795 switch has 4 external ports {0,1,2,3} and 1 CPU port {4}, so
does the KSZ8765. The KSZ8794 seems to be repackaged KSZ8795 with different
ID and port 3 not routed out, however the port 3 registers are present in
the silicon, so the KSZ8794 switch has 3 external ports {0,1,2} and 1 CPU
port {4}. Currently the driver always uses the last port as CPU port, on
KSZ8795/KSZ8765 that is port 4 and that is OK, but on KSZ8794 that is port
3 and that is not OK, as it must also be port 4.
This patch adjusts the driver such that it always registers a switch with
5 ports total (4 external ports, 1 CPU port), always sets the CPU port to
switch port 4, and then configures the external port mask according to
the switch model -- 3 ports for KSZ8794 and 4 for KSZ8795/KSZ8765.
Fixes: 68a1b676db52 ("net: dsa: microchip: ksz8795: remove superfluous port_cnt assignment")
Fixes: 4ce2a984abd8 ("net: dsa: microchip: ksz8795: use phy_port_cnt where possible")
Fixes: 241ed719bc98 ("net: dsa: microchip: ksz8795: use port_cnt instead of TOTOAL_PORT_NUM")
Signed-off-by: Marek Vasut <marex@...x.de>
Cc: Andrew Lunn <andrew@...n.ch>
Cc: Florian Fainelli <f.fainelli@...il.com>
Cc: Michael Grzeschik <m.grzeschik@...gutronix.de>
Cc: Jakub Kicinski <kuba@...nel.org>
---
NOTE: In case of KSZ8794, the DT node port@4 is the CPU port and
port@3 should not be defined.
---
drivers/net/dsa/microchip/ksz8795.c | 30 +++++++++++++++++++----------
1 file changed, 20 insertions(+), 10 deletions(-)
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index c973db101b72..a4570ba29c83 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -1187,6 +1187,20 @@ static const struct ksz_chip_data ksz8795_switch_chips[] = {
.port_cnt = 5, /* total cpu and user ports */
},
{
+ /*
+ * WARNING
+ * =======
+ * KSZ8794 is similar to KSZ8795, except the port map
+ * contains a gap between external and CPU ports, the
+ * port map is NOT continuous. The per-port register
+ * map is shifted accordingly too, i.e. registers at
+ * offset 0x40 are NOT used on KSZ8794 and they ARE
+ * used on KSZ8795 for external port 3.
+ * external cpu
+ * KSZ8794 0,1,2 4
+ * KSZ8795 0,1,2,3 4
+ * KSZ8765 0,1,2,3 4
+ */
.chip_id = 0x8794,
.dev_name = "KSZ8794",
.num_vlans = 4096,
@@ -1220,9 +1234,13 @@ static int ksz8795_switch_init(struct ksz_device *dev)
dev->num_vlans = chip->num_vlans;
dev->num_alus = chip->num_alus;
dev->num_statics = chip->num_statics;
- dev->port_cnt = chip->port_cnt;
+ dev->port_cnt = fls(chip->cpu_ports);
+ dev->cpu_port = fls(chip->cpu_ports) - 1;
+ dev->phy_port_cnt = dev->port_cnt - 1;
dev->cpu_ports = chip->cpu_ports;
-
+ dev->host_mask = chip->cpu_ports;
+ dev->port_mask = (BIT(dev->phy_port_cnt) - 1) |
+ chip->cpu_ports;
break;
}
}
@@ -1231,17 +1249,9 @@ static int ksz8795_switch_init(struct ksz_device *dev)
if (!dev->cpu_ports)
return -ENODEV;
- dev->port_mask = BIT(dev->port_cnt) - 1;
- dev->port_mask |= dev->host_mask;
-
dev->reg_mib_cnt = KSZ8795_COUNTER_NUM;
dev->mib_cnt = ARRAY_SIZE(mib_names);
- dev->phy_port_cnt = dev->port_cnt - 1;
-
- dev->cpu_port = dev->port_cnt - 1;
- dev->host_mask = BIT(dev->cpu_port);
-
dev->ports = devm_kzalloc(dev->dev,
dev->port_cnt * sizeof(struct ksz_port),
GFP_KERNEL);
--
2.29.2
Powered by blists - more mailing lists