| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1612685964-21890-11-git-send-email-stefanc@marvell.com>
Date: Sun, 7 Feb 2021 10:19:19 +0200
From: <stefanc@...vell.com>
To: <netdev@...r.kernel.org>
CC: <thomas.petazzoni@...tlin.com>, <davem@...emloft.net>,
<nadavh@...vell.com>, <ymarkman@...vell.com>,
<linux-kernel@...r.kernel.org>, <stefanc@...vell.com>,
<kuba@...nel.org>, <linux@...linux.org.uk>, <mw@...ihalf.com>,
<andrew@...n.ch>, <rmk+kernel@...linux.org.uk>,
<atenart@...nel.org>, <devicetree@...r.kernel.org>,
<robh+dt@...nel.org>, <sebastian.hesselbarth@...il.com>,
<gregory.clement@...tlin.com>,
<linux-arm-kernel@...ts.infradead.org>
Subject: [RESEND PATCH v8 net-next 10/15] net: mvpp2: add RXQ flow control configurations
From: Stefan Chulski <stefanc@...vell.com>
This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: Stefan Chulski <stefanc@...vell.com>
---
drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 35 +++++-
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 116 ++++++++++++++++++++
2 files changed, 150 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index e010410..0f27be0 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -766,9 +766,36 @@
#define MSS_SRAM_SIZE 0x800
#define MSS_FC_COM_REG 0
#define FLOW_CONTROL_ENABLE_BIT BIT(0)
+#define FLOW_CONTROL_UPDATE_COMMAND_BIT BIT(31)
#define FC_QUANTA 0xFFFF
#define FC_CLK_DIVIDER 100
-#define MSS_THRESHOLD_STOP 768
+
+#define MSS_RXQ_TRESH_BASE 0x200
+#define MSS_RXQ_TRESH_OFFS 4
+#define MSS_RXQ_TRESH_REG(q, fq) (MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
+ * MSS_RXQ_TRESH_OFFS))
+
+#define MSS_RXQ_TRESH_START_MASK 0xFFFF
+#define MSS_RXQ_TRESH_STOP_MASK (0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
+#define MSS_RXQ_TRESH_STOP_OFFS 16
+
+#define MSS_RXQ_ASS_BASE 0x80
+#define MSS_RXQ_ASS_OFFS 4
+#define MSS_RXQ_ASS_PER_REG 4
+#define MSS_RXQ_ASS_PER_OFFS 8
+#define MSS_RXQ_ASS_PORTID_OFFS 0
+#define MSS_RXQ_ASS_PORTID_MASK 0x3
+#define MSS_RXQ_ASS_HOSTID_OFFS 2
+#define MSS_RXQ_ASS_HOSTID_MASK 0x3F
+
+#define MSS_RXQ_ASS_Q_BASE(q, fq) ((((q) + (fq)) % MSS_RXQ_ASS_PER_REG) \
+ * MSS_RXQ_ASS_PER_OFFS)
+#define MSS_RXQ_ASS_PQ_BASE(q, fq) ((((q) + (fq)) / MSS_RXQ_ASS_PER_REG) \
+ * MSS_RXQ_ASS_OFFS)
+#define MSS_RXQ_ASS_REG(q, fq) (MSS_RXQ_ASS_BASE + MSS_RXQ_ASS_PQ_BASE(q, fq))
+
+#define MSS_THRESHOLD_STOP 768
+#define MSS_THRESHOLD_START 1024
/* RX buffer constants */
#define MVPP2_SKB_SHINFO_SIZE \
@@ -1026,6 +1053,9 @@ struct mvpp2 {
/* Global TX Flow Control config */
bool global_tx_fc;
+
+ /* Spinlocks for CM3 shared memory configuration */
+ spinlock_t mss_spinlock;
};
struct mvpp2_pcpu_stats {
@@ -1188,6 +1218,9 @@ struct mvpp2_port {
bool rx_hwtstamp;
enum hwtstamp_tx_types tx_hwtstamp_type;
struct mvpp2_hwtstamp_queue tx_hwtstamp_queue[2];
+
+ /* Firmware TX flow control */
+ bool tx_fc;
};
/* The mvpp2_tx_desc and mvpp2_rx_desc structures describe the
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index fec1c81..29ba62a 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -742,6 +742,110 @@ static void *mvpp2_buf_alloc(struct mvpp2_port *port,
return data;
}
+/* Routine enable flow control for RXQs condition */
+static void mvpp2_rxq_enable_fc(struct mvpp2_port *port)
+{
+ int val, cm3_state, host_id, q;
+ int fq = port->first_rxq;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+ /* Remove Flow control enable bit to prevent race between FW and Kernel
+ * If Flow control was enabled, it would be re-enabled.
+ */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+ val &= ~FLOW_CONTROL_ENABLE_BIT;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ /* Set same Flow control for all RXQs */
+ for (q = 0; q < port->nrxqs; q++) {
+ /* Set stop and start Flow control RXQ thresholds */
+ val = MSS_THRESHOLD_START;
+ val |= (MSS_THRESHOLD_STOP << MSS_RXQ_TRESH_STOP_OFFS);
+ mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+ val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+ /* Set RXQ port ID */
+ val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+ val |= (port->id << MSS_RXQ_ASS_Q_BASE(q, fq));
+ val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+ + MSS_RXQ_ASS_HOSTID_OFFS));
+
+ /* Calculate RXQ host ID:
+ * In Single queue mode: Host ID equal to Host ID used for
+ * shared RX interrupt
+ * In Multi queue mode: Host ID equal to number of
+ * RXQ ID / number of CoS queues
+ * In Single resource mode: Host ID always equal to 0
+ */
+ if (queue_mode == MVPP2_QDIST_SINGLE_MODE)
+ host_id = port->nqvecs;
+ else if (queue_mode == MVPP2_QDIST_MULTI_MODE)
+ host_id = q;
+ else
+ host_id = 0;
+
+ /* Set RXQ host ID */
+ val |= (host_id << (MSS_RXQ_ASS_Q_BASE(q, fq)
+ + MSS_RXQ_ASS_HOSTID_OFFS));
+
+ mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+ }
+
+ /* Notify Firmware that Flow control config space ready for update */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+ val |= cm3_state;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
+/* Routine disable flow control for RXQs condition */
+static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
+{
+ int val, cm3_state, q;
+ unsigned long flags;
+ int fq = port->first_rxq;
+
+ spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+ /* Remove Flow control enable bit to prevent race between FW and Kernel
+ * If Flow control was enabled, it would be re-enabled.
+ */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+ val &= ~FLOW_CONTROL_ENABLE_BIT;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ /* Disable Flow control for all RXQs */
+ for (q = 0; q < port->nrxqs; q++) {
+ /* Set threshold 0 to disable Flow control */
+ val = 0;
+ val |= (0 << MSS_RXQ_TRESH_STOP_OFFS);
+ mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+ val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+
+ val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+
+ val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+ + MSS_RXQ_ASS_HOSTID_OFFS));
+
+ mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+ }
+
+ /* Notify Firmware that Flow control config space ready for update */
+ val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+ val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+ val |= cm3_state;
+ mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+ spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
/* Release buffer to BM */
static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
dma_addr_t buf_dma_addr,
@@ -3006,6 +3110,9 @@ static void mvpp2_cleanup_rxqs(struct mvpp2_port *port)
for (queue = 0; queue < port->nrxqs; queue++)
mvpp2_rxq_deinit(port, port->rxqs[queue]);
+
+ if (port->tx_fc)
+ mvpp2_rxq_disable_fc(port);
}
/* Init all Rx queues for port */
@@ -3018,6 +3125,10 @@ static int mvpp2_setup_rxqs(struct mvpp2_port *port)
if (err)
goto err_cleanup;
}
+
+ if (port->tx_fc)
+ mvpp2_rxq_enable_fc(port);
+
return 0;
err_cleanup:
@@ -4317,6 +4428,8 @@ static int mvpp2_check_ringparam_valid(struct net_device *dev,
if (ring->rx_pending > MVPP2_MAX_RXD_MAX)
new_rx_pending = MVPP2_MAX_RXD_MAX;
+ else if (ring->rx_pending < MSS_THRESHOLD_START)
+ new_rx_pending = MSS_THRESHOLD_START;
else if (!IS_ALIGNED(ring->rx_pending, 16))
new_rx_pending = ALIGN(ring->rx_pending, 16);
@@ -7170,6 +7283,9 @@ static int mvpp2_probe(struct platform_device *pdev)
priv->hw_version = MVPP23;
}
+ /* Init mss lock */
+ spin_lock_init(&priv->mss_spinlock);
+
/* Initialize network controller */
err = mvpp2_init(pdev, priv);
if (err < 0) {
--
1.9.1
Powered by blists - more mailing lists