netdev - stmmac driver timeout issue

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-ID: <DB8PR04MB679570F30CC2E4FEAFE942C5E6979@DB8PR04MB6795.eurprd04.prod.outlook.com>
Date:   Thu, 4 Mar 2021 13:14:31 +0000
From:   Joakim Zhang <qiangqing.zhang@....com>
To:     Jakub Kicinski <kuba@...nel.org>, Andrew Lunn <andrew@...n.ch>
CC:     "netdev@...r.kernel.org" <netdev@...r.kernel.org>
Subject: stmmac driver timeout issue

Hello Andrew, Hello Jakub,

You may can give some suggestions based on your great networking knowledge, thanks in advance!

I found that add vlan id hw filter (stmmac_vlan_rx_add_vid) have possibility timeout when accessing VLAN Filter registers during ifup/ifdown stress test, and restore vlan id hw filter (stmmac_restore_hw_vlan_rx_fltr) always timeout when access VLAN Filter registers. 

My hardware is i.MX8MP (drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c, RGMII interface, RTL8211FDI-CG PHY), it needs fix mac speed(imx_dwmac_fix_speed), it indirectly involved in phylink_link_up. After debugging, if phylink_link_up is called later than adding vlan id hw filter, it will report timeout, so I guess we need fix mac speed before accessing VLAN Filter registers. Error like below:
	[  106.389879] 8021q: adding VLAN 0 to HW filter on device eth1
	[  106.395644] imx-dwmac 30bf0000.ethernet eth1: Timeout accessing MAC_VLAN_Tag_Filter
	[  108.160734] imx-dwmac 30bf0000.ethernet eth1: Link is Up - 100Mbps/Full - flow control rx/tx   ->->-> which means accessing VLAN Filter registers before phylink_link_up is called.

Same case when system resume back, 
	[ 1763.842294] imx-dwmac 30bf0000.ethernet eth1: configuring for phy/rgmii-id link mode
	[ 1763.853084] imx-dwmac 30bf0000.ethernet eth1: No Safety Features support found
	[ 1763.853186] imx-dwmac 30bf0000.ethernet eth1: Timeout accessing MAC_VLAN_Tag_Filter
	[ 1763.873465] usb usb1: root hub lost power or was reset
	[ 1763.873469] usb usb2: root hub lost power or was reset
	[ 1764.090321] PM: resume devices took 0.248 seconds
	[ 1764.257381] OOM killer enabled.
	[ 1764.260518] Restarting tasks ... done.
	[ 1764.265229] PM: suspend exit
	===============================
	suspend 12 times
	===============================
	[ 1765.887915] imx-dwmac 30bf0000.ethernet eth1: Link is Up - 100Mbps/Full - flow control rx/tx  ->->-> which means accessing VLAN Filter registers before phylink_link_up is called.

My question is that some MAC controllers need RXC clock from RGMII interface to reset DAM or access to some registers. If there is any way to ensure phylink_link_up is invoked synchronously when we need it. I am not sure this timeout caused by a fix mac speed is needed before accessing VLAN Filter registers, is there ang hints, thanks a lot! We have another board i.MX8DXL which don't need fix mac speed attach to AR8031 PHY, can't reproduce this issue.

Best Regards,
Joakim Zhang