| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <4902bb0e-87ad-3fa4-f7af-bbe7b43ad68f@helixd.com>
Date: Fri, 6 Aug 2021 16:46:08 -0700
From: Dario Alcocer <dalcocer@...ixd.com>
To: Andrew Lunn <andrew@...n.ch>
Cc: netdev@...r.kernel.org
Subject: Re: Marvell switch port shows LOWERLAYERDOWN, ping fails
Andrew,
Using 5.13.8 resolves the LOWERLAYERDOWN issue I observed when bringing
up a slave interface on 5.4.114. The interface comes up after a
15-second delay, with the Marvell PHY driver reporting a downshift event:
root@...i:~# ip addr add 192.0.2.1/24 dev lan1
root@...i:~# ip link set lan1 up
[ 264.992698] socfpga-dwmac ff700000.ethernet eth0: Register
MEM_TYPE_PAGE_POOL RxQ-0
[ 264.997303] socfpga-dwmac ff700000.ethernet eth0: No Safety Features
support found
[ 264.998167] socfpga-dwmac ff700000.ethernet eth0: IEEE 1588-2008
Advanced Timestamp supported
[ 264.999357] socfpga-dwmac ff700000.ethernet eth0: registered PTP clock
[ 265.000804] socfpga-dwmac ff700000.ethernet eth0: configuring for
fixed/gmii link mode
[ 265.002542] socfpga-dwmac ff700000.ethernet eth0: Link is Up -
1Gbps/Full - flow control rx/tx
[ 265.007121] mv88e6085 stmmac-0:1a lan1: configuring for phy/gmii link
mode
[ 265.015320] 8021q: adding VLAN 0 to HW filter on device lan1
[ 265.016921] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
root@...i:~# [ 280.856989] Marvell 88E1540 mv88e6xxx-0:00: Downshift
occurred from negotiated speed 1Gbps to actual speed 100Mbps, check cabling!
[ 280.858797] mv88e6085 stmmac-0:1a lan1: Link is Up - 100Mbps/Full -
flow control rx/tx
[ 280.859713] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
Unfortunately, the single-port DSA configuration showcase example (from
Documentation/networking/dsa/configuration.rst) still does not pass ICMP
via the lan1 port:
root@...i:~# ping 192.0.2.2
PING 192.0.2.2 (192.0.2.2): 56 data bytes
^C
--- 192.0.2.2 ping statistics ---
12 packets transmitted, 0 packets received, 100% packet loss
root@...i:~#
Running tcpdump indicates ARP packets are sent to eth0, but the lan1
link peer does not reply:
root@...i:~# tcpdump -i eth0
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
12:15:11.248264 MEDSA 1.1:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ea:38:64:39:ee:b2 (oui Unknown), length 548
12:15:13.805980 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:14.849210 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:15.889193 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:16.238290 MEDSA 1.1:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ea:38:64:39:ee:b2 (oui Unknown), length 548
12:15:17.806438 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:18.849208 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:19.889200 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:21.238306 MEDSA 1.1:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ea:38:64:39:ee:b2 (oui Unknown), length 548
12:15:21.806994 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:22.849200 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:23.889195 MEDSA 0.0:0: ARP, Request who-has 192.0.2.2 tell
192.0.2.1, length 28
12:15:26.238330 MEDSA 1.1:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ea:38:64:39:ee:b2 (oui Unknown), length 548
12:15:31.238361 MEDSA 1.1:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ea:38:64:39:ee:b2 (oui Unknown), length 548
12:15:31.259217 IP6 fe80::801d:a3ff:fea2:b66b > ip6-allrouters: ICMP6,
router solicitation, length 16
12:15:36.238375 MEDSA 1.1:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ea:38:64:39:ee:b2 (oui Unknown), length 548
12:15:50.405148 MEDSA 1.0:0: IP6 fe80::b8de:29ff:fed8:d469 >
ip6-allrouters: ICMP6, router solicitation, length 16
12:15:52.234783 MEDSA 1.0:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ba:de:29:d8:d4:69 (oui Unknown), length 548
12:15:57.235155 MEDSA 1.0:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ba:de:29:d8:d4:69 (oui Unknown), length 548
12:16:01.969215 MEDSA 0.0:0: IP6 fe80::801d:a3ff:fea2:b66b >
ip6-allrouters: ICMP6, router solicitation, length 16
12:16:02.234543 MEDSA 1.0:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ba:de:29:d8:d4:69 (oui Unknown), length 548
12:16:07.234883 MEDSA 1.0:0: IP 0.0.0.0.bootpc > 255.255.255.255.bootps:
BOOTP/DHCP, Request from ba:de:29:d8:d4:69 (oui Unknown), length 548
^C
22 packets captured[ 977.987343] device eth0 left promiscuous mode
2
22 packets received by filter
0 packets dropped by kernel
root@...i:~#
Running tcpdump on the link peer shows no Ethernet frames are being
received.
Port registers for both switches:
root@...i:~# mv88e6xxx_dump --list
mdio_bus/stmmac-0:1a
mdio_bus/stmmac-0:1e
root@...i:~# mv88e6xxx_dump --ports --device mdio_bus/stmmac-0:1a
0 1 2 3 4 5 6
00 Port status 9d0f 100f 100f 100f 1e0f 0009 0d04
01 Physical control 0003 0003 0003 0003 003e 0003 0003
02 Jamming control 0000 0000 0000 ff00 0000 ff00 ff00
03 Switch ID 1761 1761 1761 1761 1761 1761 1761
04 Port control 043f 043f 043f 007c 053f 007c 007c
05 Port control 1 0000 0000 0000 0000 8000 0000 0000
06 Port base VLAN map 0010 0010 0010 0077 006f 005f 003f
07 Def VLAN ID & Prio 0000 0000 0000 0001 0000 0001 0001
08 Port control 2 0080 0080 0080 2080 0080 2080 2080
09 Egress rate control 0001 0001 0001 0001 0001 0001 0001
0a Egress rate control 2 0000 0000 0000 8000 0000 8000 8000
0b Port association vec 0000 0000 0000 0008 0010 0020 0040
0c Port ATU control 0000 0000 0000 0000 0000 0000 0000
0d Override 0000 0000 0000 0000 0000 0000 0000
0e Policy control 0000 0000 0000 0000 0000 0000 0000
0f Port ether type 9100 9100 9100 9100 9100 9100 9100
10 In discard low 0000 0000 0000 0000 0000 0000 0000
11 In discard high 0000 0000 0000 0000 0000 0000 0000
12 In filtered 0000 0000 0000 0000 0000 0000 0000
13 RX frame count 0105 0000 0000 0000 0000 0000 0000
14 Reserved 0000 0000 0000 0000 0000 0000 0000
15 Reserved 0000 0000 0000 0000 0000 0000 0000
16 LED control 0033 0033 0033 0033 0033 0033 0000
17 Reserved 0000 0000 0000 0000 0000 0000 0000
18 Tag remap low 3210 3210 3210 3210 3210 3210 3210
19 Tag remap high 7654 7654 7654 7654 7654 7654 7654
1a Reserved 0000 0000 0000 0000 0000 0000 0000
1b Queue counters 8000 8000 8000 8000 8000 8000 8000
1c Reserved 0000 0000 0000 0000 0000 0000 0000
1d Reserved 0000 0000 0000 0000 0000 0000 0000
1e Reserved 0000 0000 0000 0000 0000 0000 0000
1f Reserved 0000 0000 0000 0000 0000 0000 0000
root@...i:~# mv88e6xxx_dump --ports --device mdio_bus/stmmac-0:1e
0 1 2 3 4 5 6
00 Port status 1d0f 1d0f 100f 100f 1e0f 0009 0e03
01 Physical control 0003 0003 0003 0003 003e 0003 003e
02 Jamming control 0000 0000 ff00 ff00 0000 ff00 0000
03 Switch ID 1761 1761 1761 1761 1761 1761 1761
04 Port control 043f 043f 007c 007c 053f 007c 373f
05 Port control 1 0000 0000 0000 0000 8000 0000 0000
06 Port base VLAN map 0050 0050 007b 0077 006f 005f 003f
07 Def VLAN ID & Prio 0000 0000 0001 0001 0000 0001 0000
08 Port control 2 0080 0080 2080 2080 0080 2080 0080
09 Egress rate control 0001 0001 0001 0001 0001 0001 0001
0a Egress rate control 2 0000 0000 8000 8000 0000 8000 0000
0b Port association vec 0000 0000 0004 0008 0010 0020 0040
0c Port ATU control 0000 0000 0000 0000 0000 0000 0000
0d Override 0000 0000 0000 0000 0000 0000 0000
0e Policy control 0000 0000 0000 0000 0000 0000 0000
0f Port ether type 9100 9100 9100 9100 9100 9100 dada
10 In discard low 0000 0000 0000 0000 0000 0000 0000
11 In discard high 0000 0000 0000 0000 0000 0000 0000
12 In filtered 0000 0000 0000 0000 0000 0000 0000
13 RX frame count 010a 00d5 0000 0000 0000 0000 0073
14 Reserved 0000 0000 0000 0000 0000 0000 0000
15 Reserved 0000 0000 0000 0000 0000 0000 0000
16 LED control 0033 0033 0033 0033 0033 0033 0000
17 Reserved 0000 0000 0000 0000 0000 0000 0000
18 Tag remap low 3210 3210 3210 3210 3210 3210 3210
19 Tag remap high 7654 7654 7654 7654 7654 7654 7654
1a Reserved 0000 0000 0000 0000 0000 0000 0000
1b Queue counters 8000 8000 8000 8000 8000 8000 8000
1c Reserved 0000 0000 0000 0000 0000 0000 0000
1d Reserved 0000 0000 0000 0000 0000 0000 0000
1e Reserved 0000 0000 0000 0000 0000 0000 0000
1f Reserved 0000 0000 0000 0000 0000 0000 0000
Detailed info from switch 0, port 0, corresponding to lan1 port:
root@...i:~# mv88e6xxx_dump --port 0 --device mdio_bus/stmmac-0:1a
00 Port status 0x9d0f
Pause Enabled 1
My Pause 0
802.3 PHY Detected 1
Link Status Up
Duplex Full
Speed 100 or 200 Mbps
EEE Enabled 0
Transmitter Paused 0
Flow Control 0
Config Mode 0xf
01 Physical control 0x0003
RGMII Receive Timing Control Default
RGMII Transmit Timing Control Default
200 BASE Mode 100
Flow Control's Forced value 0
Force Flow Control 0
Link's Forced value Down
Force Link 0
Duplex's Forced value Half
Force Duplex 0
Force Speed Not forced
02 Jamming control 0x0000
03 Switch ID 0x1761
04 Port control 0x043f
Source Address Filtering controls Disabled
Egress Mode Unmodified
Ingress & Egress Header Mode 0
IGMP and MLD Snooping 1
Frame Mode Normal
VLAN Tunnel 0
TagIfBoth 0
Initial Priority assignment Tag & IP Priority
Egress Flooding mode Allow unknown DA
Port State Forwarding
05 Port control 1 0x0000
Message Port 0
Trunk Port 0
Trunk ID 0
FID[11:4] 0x000
06 Port base VLAN map 0x0010
FID[3:0] 0x000
VLANTable 4
07 Def VLAN ID & Prio 0x0000
Default Priority 0x0
Force to use Default VID 0
Default VLAN Identifier 0
08 Port control 2 0x0080
Force good FCS in the frame 0
Jumbo Mode 1522
802.1QMode Disabled
Discard Tagged Frames 0
Discard Untagged Frames 0
Map using DA hits 1
ARP Mirror enable 0
Egress Monitor Source Port 0
Ingress Monitor Source Port 0
Use Default Queue Priority 0
Default Queue Priority 0x0
09 Egress rate control 0x0001
0a Egress rate control 2 0x0000
0b Port association vec 0x0000
0c Port ATU control 0x0000
0d Override 0x0000
0e Policy control 0x0000
0f Port ether type 0x9100
10 In discard low 0x0000
11 In discard high 0x0000
12 In filtered 0x0000
13 RX frame count 0x010d
14 Reserved 0x0000
15 Reserved 0x0000
16 LED control 0x0033
17 Reserved 0x0000
18 Tag remap low 0x3210
19 Tag remap high 0x7654
1a Reserved 0x0000
1b Queue counters 0x8000
1c Reserved 0x0000
1d Reserved 0x0000
1e Reserved 0x0000
1f Reserved 0x0000
Detailed info for switch 0, port 4 and switch 1, port 4, which are the
DSA ports for both switches, using a SERDES link:
root@...i:~# mv88e6xxx_dump --port 4 --device mdio_bus/stmmac-0:1a
00 Port status 0x1e0f
Pause Enabled 0
My Pause 0
802.3 PHY Detected 1
Link Status Up
Duplex Full
Speed 1000 Mbps
EEE Enabled 0
Transmitter Paused 0
Flow Control 0
Config Mode 0xf
01 Physical control 0x003e
RGMII Receive Timing Control Default
RGMII Transmit Timing Control Default
200 BASE Mode 100
Flow Control's Forced value 0
Force Flow Control 0
Link's Forced value Up
Force Link 1
Duplex's Forced value Full
Force Duplex 1
Force Speed 1000 Mbps
02 Jamming control 0x0000
03 Switch ID 0x1761
04 Port control 0x053f
Source Address Filtering controls Disabled
Egress Mode Unmodified
Ingress & Egress Header Mode 0
IGMP and MLD Snooping 1
Frame Mode DSA
VLAN Tunnel 0
TagIfBoth 0
Initial Priority assignment Tag & IP Priority
Egress Flooding mode Allow unknown DA
Port State Forwarding
05 Port control 1 0x8000
Message Port 1
Trunk Port 0
Trunk ID 0
FID[11:4] 0x000
06 Port base VLAN map 0x006f
FID[3:0] 0x000
VLANTable 0 1 2 3 5 6
07 Def VLAN ID & Prio 0x0000
Default Priority 0x0
Force to use Default VID 0
Default VLAN Identifier 0
08 Port control 2 0x0080
Force good FCS in the frame 0
Jumbo Mode 1522
802.1QMode Disabled
Discard Tagged Frames 0
Discard Untagged Frames 0
Map using DA hits 1
ARP Mirror enable 0
Egress Monitor Source Port 0
Ingress Monitor Source Port 0
Use Default Queue Priority 0
Default Queue Priority 0x0
09 Egress rate control 0x0001
0a Egress rate control 2 0x0000
0b Port association vec 0x0010
0c Port ATU control 0x0000
0d Override 0x0000
0e Policy control 0x0000
0f Port ether type 0x9100
10 In discard low 0x0000
11 In discard high 0x0000
12 In filtered 0x0000
13 RX frame count 0x0000
14 Reserved 0x0000
15 Reserved 0x0000
16 LED control 0x0033
17 Reserved 0x0000
18 Tag remap low 0x3210
19 Tag remap high 0x7654
1a Reserved 0x0000
1b Queue counters 0x8000
1c Reserved 0x0000
1d Reserved 0x0000
1e Reserved 0x0000
1f Reserved 0x0000
root@...i:~# mv88e6xxx_dump --port 4 --device mdio_bus/stmmac-0:1e
00 Port status 0x1e0f
Pause Enabled 0
My Pause 0
802.3 PHY Detected 1
Link Status Up
Duplex Full
Speed 1000 Mbps
EEE Enabled 0
Transmitter Paused 0
Flow Control 0
Config Mode 0xf
01 Physical control 0x003e
RGMII Receive Timing Control Default
RGMII Transmit Timing Control Default
200 BASE Mode 100
Flow Control's Forced value 0
Force Flow Control 0
Link's Forced value Up
Force Link 1
Duplex's Forced value Full
Force Duplex 1
Force Speed 1000 Mbps
02 Jamming control 0x0000
03 Switch ID 0x1761
04 Port control 0x053f
Source Address Filtering controls Disabled
Egress Mode Unmodified
Ingress & Egress Header Mode 0
IGMP and MLD Snooping 1
Frame Mode DSA
VLAN Tunnel 0
TagIfBoth 0
Initial Priority assignment Tag & IP Priority
Egress Flooding mode Allow unknown DA
Port State Forwarding
05 Port control 1 0x8000
Message Port 1
Trunk Port 0
Trunk ID 0
FID[11:4] 0x000
06 Port base VLAN map 0x006f
FID[3:0] 0x000
VLANTable 0 1 2 3 5 6
07 Def VLAN ID & Prio 0x0000
Default Priority 0x0
Force to use Default VID 0
Default VLAN Identifier 0
08 Port control 2 0x0080
Force good FCS in the frame 0
Jumbo Mode 1522
802.1QMode Disabled
Discard Tagged Frames 0
Discard Untagged Frames 0
Map using DA hits 1
ARP Mirror enable 0
Egress Monitor Source Port 0
Ingress Monitor Source Port 0
Use Default Queue Priority 0
Default Queue Priority 0x0
09 Egress rate control 0x0001
0a Egress rate control 2 0x0000
0b Port association vec 0x0010
0c Port ATU control 0x0000
0d Override 0x0000
0e Policy control 0x0000
0f Port ether type 0x9100
10 In discard low 0x0000
11 In discard high 0x0000
12 In filtered 0x0000
13 RX frame count 0x0000
14 Reserved 0x0000
15 Reserved 0x0000
16 LED control 0x0033
17 Reserved 0x0000
18 Tag remap low 0x3210
19 Tag remap high 0x7654
1a Reserved 0x0000
1b Queue counters 0x8000
1c Reserved 0x0000
1d Reserved 0x0000
1e Reserved 0x0000
1f Reserved 0x0000
Detailed info for the CPU port connected to eth0:
root@...i:~# mv88e6xxx_dump --port 6 --device mdio_bus/stmmac-0:1e
00 Port status 0x0e03
Pause Enabled 0
My Pause 0
802.3 PHY Detected 0
Link Status Up
Duplex Full
Speed 1000 Mbps
EEE Enabled 0
Transmitter Paused 0
Flow Control 0
Config Mode 0x3
01 Physical control 0x003e
RGMII Receive Timing Control Default
RGMII Transmit Timing Control Default
200 BASE Mode 100
Flow Control's Forced value 0
Force Flow Control 0
Link's Forced value Up
Force Link 1
Duplex's Forced value Full
Force Duplex 1
Force Speed 1000 Mbps
02 Jamming control 0x0000
03 Switch ID 0x1761
04 Port control 0x373f
Source Address Filtering controls Disabled
Egress Mode Reserved
Ingress & Egress Header Mode 0
IGMP and MLD Snooping 1
Frame Mode Ether Type DSA
VLAN Tunnel 0
TagIfBoth 0
Initial Priority assignment Tag & IP Priority
Egress Flooding mode Allow unknown DA
Port State Forwarding
05 Port control 1 0x0000
Message Port 0
Trunk Port 0
Trunk ID 0
FID[11:4] 0x000
06 Port base VLAN map 0x003f
FID[3:0] 0x000
VLANTable 0 1 2 3 4 5
07 Def VLAN ID & Prio 0x0000
Default Priority 0x0
Force to use Default VID 0
Default VLAN Identifier 0
08 Port control 2 0x0080
Force good FCS in the frame 0
Jumbo Mode 1522
802.1QMode Disabled
Discard Tagged Frames 0
Discard Untagged Frames 0
Map using DA hits 1
ARP Mirror enable 0
Egress Monitor Source Port 0
Ingress Monitor Source Port 0
Use Default Queue Priority 0
Default Queue Priority 0x0
09 Egress rate control 0x0001
0a Egress rate control 2 0x0000
0b Port association vec 0x0040
0c Port ATU control 0x0000
0d Override 0x0000
0e Policy control 0x0000
0f Port ether type 0xdada
10 In discard low 0x0000
11 In discard high 0x0000
12 In filtered 0x0000
13 RX frame count 0x0073
14 Reserved 0x0000
15 Reserved 0x0000
16 LED control 0x0000
17 Reserved 0x0000
18 Tag remap low 0x3210
19 Tag remap high 0x7654
1a Reserved 0x0000
1b Queue counters 0x8000
1c Reserved 0x0000
1d Reserved 0x0000
1e Reserved 0x0000
1f Reserved 0x0000
Finally, here's the DSA info printed during boot:
Jan 1 00:00:08 (none) user.info kernel: [ 1.787590] libphy:
mv88e6xxx SMI: probed
Jan 1 00:00:08 (none) user.info kernel: [ 4.246782] mv88e6085
stmmac-0:1a lan1 (uninitialized): PHY [mv88e6xxx-0:00] driver [Marvell
88E1540] (irq=80)
Jan 1 00:00:08 (none) user.info kernel: [ 4.373236] mv88e6085
stmmac-0:1a lan2 (uninitialized): PHY [mv88e6xxx-0:01] driver [Marvell
88E1540] (irq=81)
Jan 1 00:00:08 (none) user.info kernel: [ 4.488280] mv88e6085
stmmac-0:1a lan3 (uninitialized): PHY [mv88e6xxx-0:02] driver [Marvell
88E1540] (irq=82)
Jan 1 00:00:08 (none) user.info kernel: [ 4.510657] mv88e6085
stmmac-0:1a: configuring for fixed/1000base-x link mode
Jan 1 00:00:08 (none) user.info kernel: [ 4.544236] mv88e6085
stmmac-0:1a: Link is Up - 1Gbps/Full - flow control off
Jan 1 00:00:08 (none) user.info kernel: [ 4.653347] mv88e6085
stmmac-0:1e lan4 (uninitialized): PHY [mv88e6xxx-2:00] driver [Marvell
88E1540] (irq=105)
Jan 1 00:00:08 (none) user.info kernel: [ 4.774293] mv88e6085
stmmac-0:1e dmz (uninitialized): PHY [mv88e6xxx-2:01] driver [Marvell
88E1540] (irq=106)
Jan 1 00:00:08 (none) user.info kernel: [ 4.797851] mv88e6085
stmmac-0:1e: configuring for fixed/1000base-x link mode
Jan 1 00:00:08 (none) user.info kernel: [ 4.823888] mv88e6085
stmmac-0:1e: Link is Up - 1Gbps/Full - flow control off
Jan 1 00:00:08 (none) user.info kernel: [ 4.832086] DSA: tree 0 setup
Any ideas on how to get ICMP working, using the DSA single-port
configuration example, are welcome.
Thanks!
Powered by blists - more mailing lists