| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Tue, 9 Nov 2021 04:25:17 +0100
From: Marek Behún <kabel@...nel.org>
To: Ansuel Smith <ansuelsmth@...il.com>
Cc: Andrew Lunn <andrew@...n.ch>,
Vivien Didelot <vivien.didelot@...il.com>,
Florian Fainelli <f.fainelli@...il.com>,
Vladimir Oltean <olteanv@...il.com>,
"David S. Miller" <davem@...emloft.net>,
Jakub Kicinski <kuba@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Jonathan Corbet <corbet@....net>, Pavel Machek <pavel@....cz>,
John Crispin <john@...ozen.org>, netdev@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-doc@...r.kernel.org, linux-leds@...r.kernel.org
Subject: Re: [RFC PATCH v3 6/8] leds: trigger: add hardware-phy-activity
trigger
On Tue, 9 Nov 2021 03:26:06 +0100
Ansuel Smith <ansuelsmth@...il.com> wrote:
> Add Hardware Only Trigger for PHY Activity. This special trigger is used to
> configure and expose the different HW trigger that are provided by the
> PHY. Each blink mode can be configured by sysfs and on trigger
> activation the hardware mode is enabled.
>
> This currently implement these hw triggers:
> - blink_tx: Blink LED on tx packet receive
> - blink_rx: Blink LED on rx packet receive
> - keep_link_10m: Keep LED on with 10m link speed
> - keep_link_100m: Keep LED on with 100m link speed
> - kepp_link_1000m: Keep LED on with 1000m link speed
> - keep_half_duplex: Keep LED on with half duplex link
> - keep_full_duplex: Keep LED on with full duplex link
> - option_linkup_over: Ignore blink tx/rx with link keep not active
> - option_power_on_reset: Keep LED on with switch reset
> - option_blink_2hz: Set blink speed at 2hz for every blink event
> - option_blink_4hz: Set blink speed at 4hz for every blink event
> - option_blink_8hz: Set blink speed at 8hz for every blink event
> - option_blink_auto: Set blink speed at 2hz for 10m link speed,
> 4hz for 100m and 8hz for 1000m
>
> The trigger will check if the LED driver support the various blink modes
> and will expose the blink modes in sysfs.
> It will finally enable hw mode for the LED without configuring any rule.
> This mean that the LED will blink/follow whatever offload trigger is
> active by default and the user needs to manually configure the desired
> offload triggers using sysfs.
> A flag is passed to configure_offload with the related rule from this
> trigger to active or disable.
> It's in the led driver interest the detection and knowing how to
> elaborate the passed flags and should report -EOPNOTSUPP otherwise.
>
> The different hw triggers are exposed in the led sysfs dir under the
> offload-phy-activity subdir.
>
> Signed-off-by: Ansuel Smith <ansuelsmth@...il.com>
> ---
> drivers/leds/trigger/Kconfig | 28 +++
> drivers/leds/trigger/Makefile | 1 +
> .../trigger/ledtrig-hardware-phy-activity.c | 171 ++++++++++++++++++
> include/linux/leds.h | 22 +++
> 4 files changed, 222 insertions(+)
> create mode 100644 drivers/leds/trigger/ledtrig-hardware-phy-activity.c
>
> diff --git a/drivers/leds/trigger/Kconfig b/drivers/leds/trigger/Kconfig
> index dc6816d36d06..b947b238be3f 100644
> --- a/drivers/leds/trigger/Kconfig
> +++ b/drivers/leds/trigger/Kconfig
> @@ -154,4 +154,32 @@ config LEDS_TRIGGER_TTY
>
> When build as a module this driver will be called ledtrig-tty.
>
> +config LEDS_TRIGGER_HARDWARE_PHY_ACTIVITY
> + tristate "LED Trigger for PHY Activity for Hardware Controlled LED"
> + depends on LEDS_HARDWARE_CONTROL
> + help
> + This allows LEDs to be configured to run by hardware and offloaded
> + based on some rules. The LED will blink or be on based on the PHY
> + Activity for example on packet receive or based on the link speed.
> +
> + The current supported offload triggers are:
> + - blink_tx: Blink LED on tx packet receive
> + - blink_rx: Blink LED on rx packet receive
> + - keep_link_10m: Keep LED on with 10m link speed
> + - keep_link_100m: Keep LED on with 100m link speed
> + - keep_link_1000m: Keep LED on with 1000m link speed
> + - keep_half_duplex: Keep LED on with half duplex link
> + - keep_full_duplex: Keep LED on with full duplex link
> + - option_linkup_over: Blink rules are ignored with absent link
> + - option_power_on_reset: Power ON Led on Switch/PHY reset
> + - option_blink_2hz: Set blink speed at 2hz for every blink event
> + - option_blink_4hz: Set blink speed at 4hz for every blink event
> + - option_blink_8hz: Set blink speed at 8hz for every blink event
> +
> + These blink modes are present in the LED sysfs dir under
> + hardware-phy-activity if supported by the LED driver.
> +
> + This trigger can be used only by LEDs that supports Hardware mode
> +
> +
> endif # LEDS_TRIGGERS
> diff --git a/drivers/leds/trigger/Makefile b/drivers/leds/trigger/Makefile
> index 25c4db97cdd4..f5d0d0057d2b 100644
> --- a/drivers/leds/trigger/Makefile
> +++ b/drivers/leds/trigger/Makefile
> @@ -16,3 +16,4 @@ obj-$(CONFIG_LEDS_TRIGGER_NETDEV) += ledtrig-netdev.o
> obj-$(CONFIG_LEDS_TRIGGER_PATTERN) += ledtrig-pattern.o
> obj-$(CONFIG_LEDS_TRIGGER_AUDIO) += ledtrig-audio.o
> obj-$(CONFIG_LEDS_TRIGGER_TTY) += ledtrig-tty.o
> +obj-$(CONFIG_LEDS_TRIGGER_HARDWARE_PHY_ACTIVITY) += ledtrig-hardware-phy-activity.o
> diff --git a/drivers/leds/trigger/ledtrig-hardware-phy-activity.c b/drivers/leds/trigger/ledtrig-hardware-phy-activity.c
> new file mode 100644
> index 000000000000..7fd0557fe878
> --- /dev/null
> +++ b/drivers/leds/trigger/ledtrig-hardware-phy-activity.c
> @@ -0,0 +1,171 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/leds.h>
> +#include <linux/slab.h>
> +
> +#define PHY_ACTIVITY_MAX_TRIGGERS 12
> +
> +#define DEFINE_OFFLOAD_TRIGGER(trigger_name, trigger) \
> + static ssize_t trigger_name##_show(struct device *dev, \
> + struct device_attribute *attr, char *buf) \
> + { \
> + struct led_classdev *led_cdev = led_trigger_get_led(dev); \
> + int val; \
> + val = led_cdev->hw_control_configure(led_cdev, trigger, BLINK_MODE_READ); \
> + return sprintf(buf, "%d\n", val ? 1 : 0); \
> + } \
> + static ssize_t trigger_name##_store(struct device *dev, \
> + struct device_attribute *attr, \
> + const char *buf, size_t size) \
> + { \
> + struct led_classdev *led_cdev = led_trigger_get_led(dev); \
> + unsigned long state; \
> + int cmd, ret; \
> + ret = kstrtoul(buf, 0, &state); \
> + if (ret) \
> + return ret; \
> + cmd = !!state ? BLINK_MODE_ENABLE : BLINK_MODE_DISABLE; \
> + /* Update the configuration with every change */ \
> + led_cdev->hw_control_configure(led_cdev, trigger, cmd); \
> + return size; \
> + } \
> + DEVICE_ATTR_RW(trigger_name)
> +
> +/* Expose sysfs for every blink to be configurable from userspace */
> +DEFINE_OFFLOAD_TRIGGER(blink_tx, BLINK_TX);
> +DEFINE_OFFLOAD_TRIGGER(blink_rx, BLINK_RX);
> +DEFINE_OFFLOAD_TRIGGER(keep_link_10m, KEEP_LINK_10M);
> +DEFINE_OFFLOAD_TRIGGER(keep_link_100m, KEEP_LINK_100M);
> +DEFINE_OFFLOAD_TRIGGER(keep_link_1000m, KEEP_LINK_1000M);
> +DEFINE_OFFLOAD_TRIGGER(keep_half_duplex, KEEP_HALF_DUPLEX);
> +DEFINE_OFFLOAD_TRIGGER(keep_full_duplex, KEEP_FULL_DUPLEX);
> +DEFINE_OFFLOAD_TRIGGER(option_linkup_over, OPTION_LINKUP_OVER);
> +DEFINE_OFFLOAD_TRIGGER(option_power_on_reset, OPTION_POWER_ON_RESET);
> +DEFINE_OFFLOAD_TRIGGER(option_blink_2hz, OPTION_BLINK_2HZ);
> +DEFINE_OFFLOAD_TRIGGER(option_blink_4hz, OPTION_BLINK_4HZ);
> +DEFINE_OFFLOAD_TRIGGER(option_blink_8hz, OPTION_BLINK_8HZ);
This is very strange. Is option_blink_2hz a trigger on itself? Or just
an option for another trigger? It seems that it is an option, so that I
can set something like
blink_tx,option_blink_2hz
and the LED will blink on tx activity with frequency 2 Hz... If that is
so, I think you are misnaming your macros or something, since you are
defining option_blink_2hz as a trigger with
DEFINE_OFFLOAD_TRIGGER
Marek
Powered by blists - more mailing lists