[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <603a03f4-2765-c8e7-085c-808f67b42fa9@kupper.org>
Date: Mon, 7 Feb 2022 18:59:48 +0100
From: Thomas Kupper <thomas@...per.org>
To: Shyam Sundar S K <Shyam-sundar.S-k@....com>,
Tom Lendacky <thomas.lendacky@....com>
Cc: netdev@...r.kernel.org
Subject: Re: AMD XGBE "phy irq request failed" kernel v5.17-rc2 on V1500B
based board
Am 07.02.22 um 16:19 schrieb Shyam Sundar S K:
>
> On 2/7/2022 8:02 PM, Tom Lendacky wrote:
>> On 2/5/22 12:14, Thomas Kupper wrote:
>>> Am 05.02.22 um 16:51 schrieb Tom Lendacky:
>>>> On 2/5/22 04:06, Thomas Kupper wrote:
>>>> Reloading the module and specify the dyndbg option to get some
>>>> additional debug output.
>>>>
>>>> I'm adding Shyam to the thread, too, as I'm not familiar with the
>>>> configuration for this chip.
>>>>
>>> Right after boot:
>>>
>>> [ 5.352977] amd-xgbe 0000:06:00.1 eth0: net device enabled
>>> [ 5.354198] amd-xgbe 0000:06:00.2 eth1: net device enabled
>>> ...
>>> [ 5.382185] amd-xgbe 0000:06:00.1 enp6s0f1: renamed from eth0
>>> [ 5.426931] amd-xgbe 0000:06:00.2 enp6s0f2: renamed from eth1
>>> ...
>>> [ 9.701637] amd-xgbe 0000:06:00.2 enp6s0f2: phy powered off
>>> [ 9.701679] amd-xgbe 0000:06:00.2 enp6s0f2: CL73 AN disabled
>>> [ 9.701715] amd-xgbe 0000:06:00.2 enp6s0f2: CL37 AN disabled
>>> [ 9.738191] amd-xgbe 0000:06:00.2 enp6s0f2: starting PHY
>>> [ 9.738219] amd-xgbe 0000:06:00.2 enp6s0f2: starting I2C
>>> ...
>>> [ 10.742622] amd-xgbe 0000:06:00.2 enp6s0f2: firmware mailbox
>>> command did not complete
>>> [ 10.742710] amd-xgbe 0000:06:00.2 enp6s0f2: firmware mailbox reset
>>> performed
>>> [ 10.750813] amd-xgbe 0000:06:00.2 enp6s0f2: 10GbE SFI mode set
>>> [ 10.768366] amd-xgbe 0000:06:00.2 enp6s0f2: 10GbE SFI mode set
>>> [ 10.768371] amd-xgbe 0000:06:00.2 enp6s0f2: fixed PHY configuration
>>>
>>> Then after 'ifconfig enp6s0f2 up':
>>>
>>> [ 189.184928] amd-xgbe 0000:06:00.2 enp6s0f2: phy powered off
>>> [ 189.191828] amd-xgbe 0000:06:00.2 enp6s0f2: 10GbE SFI mode set
>>> [ 189.191863] amd-xgbe 0000:06:00.2 enp6s0f2: CL73 AN disabled
>>> [ 189.191894] amd-xgbe 0000:06:00.2 enp6s0f2: CL37 AN disabled
>>> [ 189.196338] amd-xgbe 0000:06:00.2 enp6s0f2: starting PHY
>>> [ 189.198792] amd-xgbe 0000:06:00.2 enp6s0f2: 10GbE SFI mode set
>>> [ 189.212036] genirq: Flags mismatch irq 69. 00000000 (enp6s0f2-pcs)
>>> vs. 00000000 (enp6s0f2-pcs)
>>> [ 189.221700] amd-xgbe 0000:06:00.2 enp6s0f2: phy irq request failed
>>> [ 189.231051] amd-xgbe 0000:06:00.2 enp6s0f2: phy powered off
>>> [ 189.231054] amd-xgbe 0000:06:00.2 enp6s0f2: stopping I2C
>>>
>> Please ensure that the ethtool msglvl is on for drv and probe. I was
>> expecting to see some additional debug messages that I don't see here.
>>
>> Also, if you can provide the lspci output for the device (using -nn and
>> -vv) that might be helpful as well.
>>
>> Shyam will be the best one to understand what is going on here.
> On some other platforms, we have seen similar kind of problems getting
> reported. There is a fix sent for validation.
>
> The root cause is that removal of xgbe driver is causing interrupt storm
> on the MP2 device (Sensor Fusion Hub).
>
> Shall submit a fix soon to upstream once the validation is done, you may
> give it a try with that and see if that helps.
>
> Thanks,
> Shyam
>
>> Thanks,
>> Tom
Shyam, I will check the git logs for the relevant commit then from time
to time.
Looking at the code diff from OPNsense and the latest Linux kernel I
assumed that there would much more to do then fix a irq strom (but I
have no idea about the inner working of the kernel).
Nevermind: Setting the 'msglvl 0x3' with ethtool the following info can
be found in dmesg:
Running : $ ifconfig enp6s0f2 up
SIOCSIFFLAGS: Invalid argument
... and 'dmesg':
[ 55.177447] amd-xgbe 0000:06:00.2 enp6s0f2: channel-0: cpu=0, node=0
[ 55.177456] amd-xgbe 0000:06:00.2 enp6s0f2: channel-0:
dma_regs=00000000d11bf3f1, dma_irq=74, tx=00000000dd57b5c4,
rx=00000000d73e70f8
[ 55.177464] amd-xgbe 0000:06:00.2 enp6s0f2: channel-1: cpu=1, node=0
[ 55.177467] amd-xgbe 0000:06:00.2 enp6s0f2: channel-1:
dma_regs=000000000d972dd7, dma_irq=75, tx=00000000573bcff8,
rx=000000003d9a6f65
[ 55.177473] amd-xgbe 0000:06:00.2 enp6s0f2: channel-2: cpu=2, node=0
[ 55.177476] amd-xgbe 0000:06:00.2 enp6s0f2: channel-2:
dma_regs=0000000046f71179, dma_irq=76, tx=00000000897116c9,
rx=0000000004ba17e7
[ 55.177480] amd-xgbe 0000:06:00.2 enp6s0f2: channel-0 - Tx ring:
[ 55.177502] amd-xgbe 0000:06:00.2 enp6s0f2: rdesc=00000000794657ba,
rdesc_dma=0x000000010fad8000, rdata=0000000008ace7d8, node=0
[ 55.177507] amd-xgbe 0000:06:00.2 enp6s0f2: channel-0 - Rx ring:
[ 55.177523] amd-xgbe 0000:06:00.2 enp6s0f2: rdesc=000000009313d9b3,
rdesc_dma=0x0000000114538000, rdata=00000000510e3b77, node=0
[ 55.177527] amd-xgbe 0000:06:00.2 enp6s0f2: channel-1 - Tx ring:
[ 55.177543] amd-xgbe 0000:06:00.2 enp6s0f2: rdesc=00000000d26d9194,
rdesc_dma=0x000000010a774000, rdata=00000000b9419829, node=0
[ 55.177547] amd-xgbe 0000:06:00.2 enp6s0f2: channel-1 - Rx ring:
[ 55.177564] amd-xgbe 0000:06:00.2 enp6s0f2: rdesc=0000000007bf60dd,
rdesc_dma=0x000000010fb84000, rdata=00000000aa48e8c0, node=0
[ 55.177568] amd-xgbe 0000:06:00.2 enp6s0f2: channel-2 - Tx ring:
[ 55.177584] amd-xgbe 0000:06:00.2 enp6s0f2: rdesc=00000000e7e6c52e,
rdesc_dma=0x000000010fa2a000, rdata=0000000017b5d85c, node=0
[ 55.177587] amd-xgbe 0000:06:00.2 enp6s0f2: channel-2 - Rx ring:
[ 55.177603] amd-xgbe 0000:06:00.2 enp6s0f2: rdesc=000000000898fbf4,
rdesc_dma=0x0000000101f08000, rdata=00000000aded7d4c, node=0
[ 55.182366] amd-xgbe 0000:06:00.2 enp6s0f2: TXq0 mapped to TC0
[ 55.182381] amd-xgbe 0000:06:00.2 enp6s0f2: TXq1 mapped to TC1
[ 55.182388] amd-xgbe 0000:06:00.2 enp6s0f2: TXq2 mapped to TC2
[ 55.182395] amd-xgbe 0000:06:00.2 enp6s0f2: PRIO0 mapped to RXq0
[ 55.182400] amd-xgbe 0000:06:00.2 enp6s0f2: PRIO1 mapped to RXq0
[ 55.182405] amd-xgbe 0000:06:00.2 enp6s0f2: PRIO2 mapped to RXq0
[ 55.182410] amd-xgbe 0000:06:00.2 enp6s0f2: PRIO3 mapped to RXq1
[ 55.182414] amd-xgbe 0000:06:00.2 enp6s0f2: PRIO4 mapped to RXq1
[ 55.182418] amd-xgbe 0000:06:00.2 enp6s0f2: PRIO5 mapped to RXq1
[ 55.182423] amd-xgbe 0000:06:00.2 enp6s0f2: PRIO6 mapped to RXq2
[ 55.182427] amd-xgbe 0000:06:00.2 enp6s0f2: PRIO7 mapped to RXq2
[ 55.182473] amd-xgbe 0000:06:00.2 enp6s0f2: 3 Tx hardware queues,
21760 byte fifo per queue
[ 55.182501] amd-xgbe 0000:06:00.2 enp6s0f2: 3 Rx hardware queues,
21760 byte fifo per queue
[ 55.182544] amd-xgbe 0000:06:00.2 enp6s0f2: flow control enabled for RXq0
[ 55.182550] amd-xgbe 0000:06:00.2 enp6s0f2: flow control enabled for RXq1
[ 55.182556] amd-xgbe 0000:06:00.2 enp6s0f2: flow control enabled for RXq2
[ 56.178946] amd-xgbe 0000:06:00.2 enp6s0f2: SFP detected:
[ 56.178954] amd-xgbe 0000:06:00.2 enp6s0f2: vendor: MikroTik
[ 56.178958] amd-xgbe 0000:06:00.2 enp6s0f2: part number: S+AO0005
[ 56.178961] amd-xgbe 0000:06:00.2 enp6s0f2: revision level: 1.0
[ 56.178963] amd-xgbe 0000:06:00.2 enp6s0f2: serial number:
STST050B1900001
Then running '$ rmmod amd_xgbe' produced the following dmesg output:
[ 504.272482] ------------[ cut here ]------------
[ 504.272489] remove_proc_entry: removing non-empty directory 'irq/72',
leaking at least 'enp6s0f2-i2c'
[ 504.272500] WARNING: CPU: 0 PID: 803 at fs/proc/generic.c:715
remove_proc_entry+0x196/0x1b0
[ 504.272525] Modules linked in: nls_iso8859_1 intel_rapl_msr
intel_rapl_common snd_hda_intel edac_mce_amd snd_intel_dspcfg
snd_intel_sdw_acpi snd_hda_codec snd_hda_core snd_hwdep kvm snd_pcm rapl
snd_timer snd_rn_pci_acp3x snd k10temp efi_pstore soundcore
snd_pci_acp3x ccp mac_hid sch_fq_codel msr drm ip_tables x_tables
autofs4 btrfs blake2b_generic zstd_compress raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq
libcrc32c raid1 raid0 multipath linear crct10dif_pclmul crc32_pclmul
ghash_clmulni_intel aesni_intel crypto_simd cryptd amd_xgbe(-) xhci_pci
igb i2c_piix4 i2c_amd_mp2_pci xhci_pci_renesas nvme dca i2c_algo_bit
nvme_core video spi_amd
[ 504.272603] CPU: 0 PID: 803 Comm: rmmod Not tainted 5.17.0-rc2-tk #8
[ 504.272608] Hardware name: Deciso B.V. DEC2700 - OPNsense
Appliance/Netboard-A10 Gen.3, BIOS 05.32.50.0012-A10.20 11/15/2021
[ 504.272612] RIP: 0010:remove_proc_entry+0x196/0x1b0
[ 504.272619] Code: a8 1d de 92 48 85 c0 48 8d 90 78 ff ff ff 48 0f 45
c2 49 8b 54 24 78 4c 8b 80 a0 00 00 00 48 8b 92 a0 00 00 00 e8 28 53 81
00 <0f> 0b e9 44 ff ff ff e8 6e bd 87 00 66 66 2e 0f 1f 84 00 00 00 00
[ 504.272623] RSP: 0018:ffffa22a810b7b88 EFLAGS: 00010282
[ 504.272627] RAX: 0000000000000000 RBX: ffff8d8c8022ccc0 RCX:
0000000000000000
[ 504.272630] RDX: 0000000000000001 RSI: ffffffff92dbc031 RDI:
00000000ffffffff
[ 504.272632] RBP: ffffa22a810b7bb8 R08: 0000000000000000 R09:
ffffa22a810b7978
[ 504.272635] R10: ffffa22a810b7970 R11: ffffffff93155f48 R12:
ffff8d8c90dc0540
[ 504.272637] R13: ffff8d8c90dc05c0 R14: 0000000000000049 R15:
0000000000000049
[ 504.272639] FS: 00007fb60c99b400(0000) GS:ffff8d8caae00000(0000)
knlGS:0000000000000000
[ 504.272643] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 504.272645] CR2: 00007f86e9192f68 CR3: 0000000111b46000 CR4:
00000000003506f0
[ 504.272648] Call Trace:
[ 504.272650] <TASK>
[ 504.272656] unregister_irq_proc+0xe4/0x110
[ 504.272664] free_desc+0x2e/0x70
[ 504.272669] irq_free_descs+0x50/0x80
[ 504.272674] irq_domain_free_irqs+0x16b/0x1c0
[ 504.272678] __msi_domain_free_irqs+0xf1/0x160
[ 504.272683] msi_domain_free_irqs_descs_locked+0x20/0x50
[ 504.272687] pci_msi_teardown_msi_irqs+0x49/0x50
[ 504.272692] pci_disable_msix.part.0+0xff/0x160
[ 504.272695] pci_free_irq_vectors+0x45/0x60
[ 504.272699] xgbe_pci_remove+0x24/0x40 [amd_xgbe]
[ 504.272717] pci_device_remove+0x39/0xa0
[ 504.272724] __device_release_driver+0x181/0x250
[ 504.272731] driver_detach+0xd3/0x120
[ 504.272736] bus_remove_driver+0x59/0xd0
[ 504.272739] driver_unregister+0x31/0x50
[ 504.272743] pci_unregister_driver+0x40/0x90
[ 504.272748] xgbe_pci_exit+0x15/0x20 [amd_xgbe]
[ 504.272766] xgbe_mod_exit+0x9/0x8b0 [amd_xgbe]
[ 504.272784] __do_sys_delete_module.constprop.0+0x183/0x290
[ 504.272791] ? syscall_exit_to_user_mode+0x27/0x50
[ 504.272799] __x64_sys_delete_module+0x12/0x20
[ 504.272804] do_syscall_64+0x5c/0xc0
[ 504.272809] ? irqentry_exit+0x33/0x40
[ 504.272813] ? exc_page_fault+0x89/0x180
[ 504.272818] ? asm_exc_page_fault+0x8/0x30
[ 504.272822] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 504.272828] RIP: 0033:0x7fb60caca8eb
[ 504.272833] Code: 73 01 c3 48 8b 0d 45 e5 0e 00 f7 d8 64 89 01 48 83
c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f
05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 15 e5 0e 00 f7 d8 64 89 01 48
[ 504.272836] RSP: 002b:00007ffd82036228 EFLAGS: 00000206 ORIG_RAX:
00000000000000b0
[ 504.272840] RAX: ffffffffffffffda RBX: 00007fb60e79b760 RCX:
00007fb60caca8eb
[ 504.272843] RDX: 000000000000000a RSI: 0000000000000800 RDI:
00007fb60e79b7c8
[ 504.272845] RBP: 0000000000000000 R08: 0000000000000000 R09:
0000000000000000
[ 504.272847] R10: 00007fb60cb62ac0 R11: 0000000000000206 R12:
00007ffd82036480
[ 504.272850] R13: 00007ffd820368b6 R14: 00007fb60e79b2a0 R15:
00007fb60e79b760
[ 504.272855] </TASK>
[ 504.272857] ---[ end trace 0000000000000000 ]---
[ 504.272917] ------------[ cut here ]------------
[ 504.272919] remove_proc_entry: removing non-empty directory 'irq/73',
leaking at least 'enp6s0f2-pcs'
[ 504.272930] WARNING: CPU: 0 PID: 803 at fs/proc/generic.c:715
remove_proc_entry+0x196/0x1b0
[ 504.272938] Modules linked in: nls_iso8859_1 intel_rapl_msr
intel_rapl_common snd_hda_intel edac_mce_amd snd_intel_dspcfg
snd_intel_sdw_acpi snd_hda_codec snd_hda_core snd_hwdep kvm snd_pcm rapl
snd_timer snd_rn_pci_acp3x snd k10temp efi_pstore soundcore
snd_pci_acp3x ccp mac_hid sch_fq_codel msr drm ip_tables x_tables
autofs4 btrfs blake2b_generic zstd_compress raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq
libcrc32c raid1 raid0 multipath linear crct10dif_pclmul crc32_pclmul
ghash_clmulni_intel aesni_intel crypto_simd cryptd amd_xgbe(-) xhci_pci
igb i2c_piix4 i2c_amd_mp2_pci xhci_pci_renesas nvme dca i2c_algo_bit
nvme_core video spi_amd
[ 504.272998] CPU: 0 PID: 803 Comm: rmmod Tainted: G W
5.17.0-rc2-tk #8
[ 504.273002] Hardware name: Deciso B.V. DEC2700 - OPNsense
Appliance/Netboard-A10 Gen.3, BIOS 05.32.50.0012-A10.20 11/15/2021
[ 504.273004] RIP: 0010:remove_proc_entry+0x196/0x1b0
[ 504.273009] Code: a8 1d de 92 48 85 c0 48 8d 90 78 ff ff ff 48 0f 45
c2 49 8b 54 24 78 4c 8b 80 a0 00 00 00 48 8b 92 a0 00 00 00 e8 28 53 81
00 <0f> 0b e9 44 ff ff ff e8 6e bd 87 00 66 66 2e 0f 1f 84 00 00 00 00
[ 504.273012] RSP: 0018:ffffa22a810b7b88 EFLAGS: 00010282
[ 504.273015] RAX: 0000000000000000 RBX: ffff8d8c8022ccc0 RCX:
0000000000000000
[ 504.273018] RDX: 0000000000000001 RSI: ffffffff92dbc031 RDI:
00000000ffffffff
[ 504.273020] RBP: ffffa22a810b7bb8 R08: 0000000000000000 R09:
ffffa22a810b7978
[ 504.273022] R10: ffffa22a810b7970 R11: ffffffff93155f48 R12:
ffff8d8c8b8676c0
[ 504.273024] R13: ffff8d8c8b867740 R14: 000000000000004a R15:
000000000000004a
[ 504.273027] FS: 00007fb60c99b400(0000) GS:ffff8d8caae00000(0000)
knlGS:0000000000000000
[ 504.273030] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 504.273032] CR2: 00007f86e9192f68 CR3: 0000000111b46000 CR4:
00000000003506f0
[ 504.273035] Call Trace:
[ 504.273036] <TASK>
[ 504.273039] unregister_irq_proc+0xe4/0x110
[ 504.273044] free_desc+0x2e/0x70
[ 504.273049] irq_free_descs+0x50/0x80
[ 504.273053] irq_domain_free_irqs+0x16b/0x1c0
[ 504.273058] __msi_domain_free_irqs+0xf1/0x160
[ 504.273064] msi_domain_free_irqs_descs_locked+0x20/0x50
[ 504.273070] pci_msi_teardown_msi_irqs+0x49/0x50
[ 504.273074] pci_disable_msix.part.0+0xff/0x160
[ 504.273079] pci_free_irq_vectors+0x45/0x60
[ 504.273082] xgbe_pci_remove+0x24/0x40 [amd_xgbe]
[ 504.273098] pci_device_remove+0x39/0xa0
[ 504.273103] __device_release_driver+0x181/0x250
[ 504.273107] driver_detach+0xd3/0x120
[ 504.273110] bus_remove_driver+0x59/0xd0
[ 504.273113] driver_unregister+0x31/0x50
[ 504.273116] pci_unregister_driver+0x40/0x90
[ 504.273121] xgbe_pci_exit+0x15/0x20 [amd_xgbe]
[ 504.273136] xgbe_mod_exit+0x9/0x8b0 [amd_xgbe]
[ 504.273151] __do_sys_delete_module.constprop.0+0x183/0x290
[ 504.273156] ? syscall_exit_to_user_mode+0x27/0x50
[ 504.273161] __x64_sys_delete_module+0x12/0x20
[ 504.273165] do_syscall_64+0x5c/0xc0
[ 504.273168] ? irqentry_exit+0x33/0x40
[ 504.273172] ? exc_page_fault+0x89/0x180
[ 504.273176] ? asm_exc_page_fault+0x8/0x30
[ 504.273179] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 504.273184] RIP: 0033:0x7fb60caca8eb
[ 504.273187] Code: 73 01 c3 48 8b 0d 45 e5 0e 00 f7 d8 64 89 01 48 83
c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f
05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 15 e5 0e 00 f7 d8 64 89 01 48
[ 504.273189] RSP: 002b:00007ffd82036228 EFLAGS: 00000206 ORIG_RAX:
00000000000000b0
[ 504.273192] RAX: ffffffffffffffda RBX: 00007fb60e79b760 RCX:
00007fb60caca8eb
[ 504.273194] RDX: 000000000000000a RSI: 0000000000000800 RDI:
00007fb60e79b7c8
[ 504.273196] RBP: 0000000000000000 R08: 0000000000000000 R09:
0000000000000000
[ 504.273198] R10: 00007fb60cb62ac0 R11: 0000000000000206 R12:
00007ffd82036480
[ 504.273200] R13: 00007ffd820368b6 R14: 00007fb60e79b2a0 R15:
00007fb60e79b760
[ 504.273204] </TASK>
[ 504.273205] ---[ end trace 0000000000000000 ]---
[ 504.925023] irq 31: nobody cared (try booting with the "irqpoll" option)
[ 504.932518] CPU: 4 PID: 0 Comm: swapper/4 Tainted: G W
5.17.0-rc2-tk #8
[ 504.932524] Hardware name: Deciso B.V. DEC2700 - OPNsense
Appliance/Netboard-A10 Gen.3, BIOS 05.32.50.0012-A10.20 11/15/2021
[ 504.932526] Call Trace:
[ 504.932529] <IRQ>
[ 504.932533] dump_stack_lvl+0x4c/0x63
[ 504.932542] dump_stack+0x10/0x12
[ 504.932545] __report_bad_irq+0x3a/0xaf
[ 504.932550] note_interrupt.cold+0xb/0x60
[ 504.932554] ? __this_cpu_preempt_check+0x13/0x20
[ 504.932560] handle_irq_event+0x71/0x80
[ 504.932567] handle_fasteoi_irq+0x95/0x1e0
[ 504.932572] __common_interrupt+0x6e/0x110
[ 504.932577] common_interrupt+0xbd/0xe0
[ 504.932581] </IRQ>
[ 504.932582] <TASK>
[ 504.932584] asm_common_interrupt+0x1e/0x40
[ 504.932588] RIP: 0010:cpuidle_enter_state+0xdf/0x380
[ 504.932595] Code: ff e8 e5 88 73 ff 80 7d d7 00 74 17 9c 58 0f 1f 44
00 00 f6 c4 02 0f 85 82 02 00 00 31 ff e8 d8 9e 7a ff fb 66 0f 1f 44 00
00 <45> 85 ff 0f 88 1a 01 00 00 49 63 d7 4c 89 f1 48 2b 4d c8 48 8d 04
[ 504.932599] RSP: 0018:ffffa22a800e3e68 EFLAGS: 00000246
[ 504.932604] RAX: ffff8d8caaf00000 RBX: 0000000000000002 RCX:
000000000000001f
[ 504.932607] RDX: 0000000000000000 RSI: ffffffff92dbc031 RDI:
ffffffff92dcab7f
[ 504.932609] RBP: ffffa22a800e3ea0 R08: 000000758fe062ac R09:
000000754b94ae72
[ 504.932611] R10: 0000000000000001 R11: ffff8d8caaf2fd84 R12:
ffff8d8c933f7000
[ 504.932613] R13: ffffffff9326e3c0 R14: 000000758fe062ac R15:
0000000000000002
[ 504.932618] ? cpuidle_enter_state+0xbb/0x380
[ 504.932624] cpuidle_enter+0x2e/0x40
[ 504.932628] do_idle+0x203/0x290
[ 504.932633] cpu_startup_entry+0x20/0x30
[ 504.932637] start_secondary+0x118/0x150
[ 504.932642] secondary_startup_64_no_verify+0xd5/0xdb
[ 504.932650] </TASK>
[ 504.932651] handlers:
[ 504.935191] [<00000000dbc7353a>] amd_mp2_irq_isr [i2c_amd_mp2_pci]
[ 504.942102] Disabling IRQ #31
Cheers
Thomas
Powered by blists - more mailing lists