lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
Open Source and information security mailing list archives
| ||
|
Message-Id: <20221017164231.4192699-1-dario.binacchi@amarulasolutions.com> Date: Mon, 17 Oct 2022 18:42:26 +0200 From: Dario Binacchi <dario.binacchi@...rulasolutions.com> To: linux-kernel@...r.kernel.org Cc: michael@...rulasolutions.com, Vincent Mailhol <mailhol.vincent@...adoo.fr>, Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>, Rob Herring <robh@...nel.org>, Marc Kleine-Budde <mkl@...gutronix.de>, Amarula patchwork <linux-amarula@...rulasolutions.com>, Alexandre Torgue <alexandre.torgue@...s.st.com>, Dario Binacchi <dario.binacchi@...rulasolutions.com>, Christophe Roullier <christophe.roullier@...s.st.com>, "David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>, Jakub Kicinski <kuba@...nel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, Mark Brown <broonie@...nel.org>, Mathieu Poirier <mathieu.poirier@...aro.org>, Maxime Coquelin <mcoquelin.stm32@...il.com>, Miquel Raynal <miquel.raynal@...tlin.com>, Paolo Abeni <pabeni@...hat.com>, Patrice Chotard <patrice.chotard@...s.st.com>, Rob Herring <robh+dt@...nel.org>, Wolfgang Grandegger <wg@...ndegger.com>, devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org, linux-can@...r.kernel.org, linux-stm32@...md-mailman.stormreply.com, netdev@...r.kernel.org Subject: [RFC PATCH v5 0/5] can: bxcan: add support for ST bxCAN controller The series adds support for the basic extended CAN controller (bxCAN) found in many low- to middle-end STM32 SoCs. The driver design (one core module and one driver module) was inspired by other ST drivers (e. g. drivers/iio/adc/stm32-adc.c, drivers/iio/adc/stm32-adc-core.c) where device instances share resources. The shared resources functions are implemented in the core module, the device driver in a separate module. The driver has been tested on the stm32f469i-discovery board with a kernel version 5.19.0-rc2 in loopback + silent mode: ip link set can0 type can bitrate 125000 loopback on listen-only on ip link set up can0 candump can0 -L & cansend can0 300#AC.AB.AD.AE.75.49.AD.D1 For uboot and kernel compilation, as well as for rootfs creation I used buildroot: make stm32f469_disco_sd_defconfig make but I had to patch can-utils and busybox as can-utils and iproute are not compiled for MMU-less microcotrollers. In the case of can-utils, replacing the calls to fork() with vfork(), I was able to compile the package with working candump and cansend applications, while in the case of iproute, I ran into more than one problem and finally I decided to extend busybox's ip link command for CAN-type devices. I'm still wondering if it was really necessary, but this way I was able to test the driver. Changes in v5: - Add Rob Herring's Acked-by tag. - Add Rob Herring's Reviewed-by tag. - Put static in front of bxcan_enable_filters() definition. Changes in v4: - Remove "st,stm32f4-bxcan-core" compatible. In this way the can nodes (compatible "st,stm32f4-bxcan") are no longer children of a parent node with compatible "st,stm32f4-bxcan-core". - Add the "st,gcan" property (global can memory) to can nodes which references a "syscon" node containing the shared clock and memory addresses. - Replace the node can@...06400 (compatible "st,stm32f4-bxcan-core") with the gcan@...06600 node ("sysnode" compatible). The gcan node contains clocks and memory addresses shared by the two can nodes of which it's no longer the parent. - Add to can nodes the "st,gcan" property (global can memory) which references the gcan@...06600 node ("sysnode compatibble). - Add "dt-bindings: arm: stm32: add compatible for syscon gcan node" patch. - Drop the core driver. Thus bxcan-drv.c has been renamed to bxcan.c and moved to the drivers/net/can folder. The drivers/net/can/bxcan directory has therefore been removed. - Use the regmap_*() functions to access the shared memory registers. - Use spinlock to protect bxcan_rmw(). - Use 1 space, instead of tabs, in the macros definition. - Drop clock ref-counting. - Drop unused code. - Drop the _SHIFT macros and use FIELD_GET()/FIELD_PREP() directly. - Add BXCAN_ prefix to lec error codes. - Add the macro BXCAN_RX_MB_NUM. - Enable time triggered mode and use can_rx_offload(). - Use readx_poll_timeout() in function with timeouts. - Loop from tail to head in bxcan_tx_isr(). - Check bits of tsr register instead of pkts variable in bxcan_tx_isr(). - Don't return from bxcan_handle_state_change() if skb/cf are NULL. - Enable/disable the generation of the bus error interrupt depending on can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING. - Don't return from bxcan_handle_bus_err() if skb is NULL. - Drop statistics updating from bxcan_handle_bus_err(). - Add an empty line in front of 'return IRQ_HANDLED;' - Rename bxcan_start() to bxcan_chip_start(). - Rename bxcan_stop() to bxcan_chip_stop(). - Disable all IRQs in bxcan_chip_stop(). - Rename bxcan_close() to bxcan_ndo_stop(). - Use writel instead of bxcan_rmw() to update the dlc register. Changes in v3: - Remove 'Dario Binacchi <dariobin@...ero.it>' SOB. - Add description to the parent of the two child nodes. - Move "patterProperties:" after "properties: in top level before "required". - Add "clocks" to the "required:" list of the child nodes. - Remove 'Dario Binacchi <dariobin@...ero.it>' SOB. - Add "clocks" to can@0 node. - Remove 'Dario Binacchi <dariobin@...ero.it>' SOB. - Remove a blank line. - Remove 'Dario Binacchi <dariobin@...ero.it>' SOB. - Fix the documentation file path in the MAINTAINERS entry. - Do not increment the "stats->rx_bytes" if the frame is remote. - Remove pr_debug() call from bxcan_rmw(). Changes in v2: - Change the file name into 'st,stm32-bxcan-core.yaml'. - Rename compatibles: - st,stm32-bxcan-core -> st,stm32f4-bxcan-core - st,stm32-bxcan -> st,stm32f4-bxcan - Rename master property to st,can-master. - Remove the status property from the example. - Put the node child properties as required. - Remove a blank line. - Fix sparse errors. - Create a MAINTAINERS entry. - Remove the print of the registers address. - Remove the volatile keyword from bxcan_rmw(). - Use tx ring algorithm to manage tx mailboxes. - Use can_{get|put}_echo_skb(). - Update DT properties. Dario Binacchi (5): dt-bindings: arm: stm32: add compatible for syscon gcan node dt-bindings: net: can: add STM32 bxcan DT bindings ARM: dts: stm32: add CAN support on stm32f429 ARM: dts: stm32: add pin map for CAN controller on stm32f4 can: bxcan: add support for ST bxCAN controller .../bindings/arm/stm32/st,stm32-syscon.yaml | 2 + .../bindings/net/can/st,stm32-bxcan.yaml | 83 ++ MAINTAINERS | 7 + arch/arm/boot/dts/stm32f4-pinctrl.dtsi | 30 + arch/arm/boot/dts/stm32f429.dtsi | 29 + drivers/net/can/Kconfig | 12 + drivers/net/can/Makefile | 1 + drivers/net/can/bxcan.c | 1110 +++++++++++++++++ 8 files changed, 1274 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/can/st,stm32-bxcan.yaml create mode 100644 drivers/net/can/bxcan.c -- 2.32.0
Powered by blists - more mailing lists