| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20221109224752.17664-3-davthompson@nvidia.com>
Date: Wed, 9 Nov 2022 17:47:50 -0500
From: David Thompson <davthompson@...dia.com>
To: <davem@...emloft.net>, <edumazet@...gle.com>, <kuba@...nel.org>,
<pabeni@...hat.com>
CC: <netdev@...r.kernel.org>, <cai.huoqing@...ux.dev>, <brgl@...ev.pl>,
<limings@...dia.com>, <chenhao288@...ilicon.com>,
<huangguangbin2@...wei.com>,
David Thompson <davthompson@...dia.com>,
"Asmaa Mnebhi" <asmaa@...dia.com>
Subject: [PATCH net-next v2 2/4] mlxbf_gige: support 10M/100M/1G speeds on BlueField-3
The BlueField-3 OOB interface supports 10Mbps, 100Mbps, and 1Gbps speeds.
The external PHY is responsible for autonegotiating the speed with the
link partner. Once the autonegotiation is done, the BlueField PLU needs
to be configured accordingly.
This patch does two things:
1) Initialize the advertised control flow/duplex/speed in the probe
based on the BlueField SoC generation (2 or 3)
2) Adjust the PLU speed config in the PHY interrupt handler
Signed-off-by: David Thompson <davthompson@...dia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@...dia.com>
---
.../ethernet/mellanox/mlxbf_gige/mlxbf_gige.h | 8 ++
.../mellanox/mlxbf_gige/mlxbf_gige_main.c | 105 +++++++++++++++---
.../mellanox/mlxbf_gige/mlxbf_gige_regs.h | 21 ++++
3 files changed, 119 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h
index 421a0b1b766c..a453b9cd9033 100644
--- a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige.h
@@ -14,6 +14,7 @@
#include <linux/irqreturn.h>
#include <linux/netdevice.h>
#include <linux/irq.h>
+#include <linux/phy.h>
/* The silicon design supports a maximum RX ring size of
* 32K entries. Based on current testing this maximum size
@@ -84,6 +85,12 @@ struct mlxbf_gige_mdio_gw {
struct mlxbf_gige_reg_param st1;
};
+struct mlxbf_gige_link_cfg {
+ void (*set_phy_link_mode)(struct phy_device *phydev);
+ void (*adjust_link)(struct net_device *netdev);
+ phy_interface_t phy_mode;
+};
+
struct mlxbf_gige {
void __iomem *base;
void __iomem *llu_base;
@@ -121,6 +128,7 @@ struct mlxbf_gige {
struct mlxbf_gige_stats stats;
u8 hw_version;
struct mlxbf_gige_mdio_gw *mdio_gw;
+ int prev_speed;
};
/* Rx Work Queue Element definitions */
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c
index e08c07e914c1..32d7030eb2cf 100644
--- a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_main.c
@@ -263,13 +263,99 @@ static const struct net_device_ops mlxbf_gige_netdev_ops = {
.ndo_get_stats64 = mlxbf_gige_get_stats64,
};
-static void mlxbf_gige_adjust_link(struct net_device *netdev)
+static void mlxbf_gige_bf2_adjust_link(struct net_device *netdev)
{
struct phy_device *phydev = netdev->phydev;
phy_print_status(phydev);
}
+static void mlxbf_gige_bf3_adjust_link(struct net_device *netdev)
+{
+ struct mlxbf_gige *priv = netdev_priv(netdev);
+ struct phy_device *phydev = netdev->phydev;
+ u8 sgmii_mode;
+ u16 ipg_size;
+ u32 val;
+
+ if (phydev->link && phydev->speed != priv->prev_speed) {
+ switch (phydev->speed) {
+ case 1000:
+ ipg_size = MLXBF_GIGE_1G_IPG_SIZE;
+ sgmii_mode = MLXBF_GIGE_1G_SGMII_MODE;
+ break;
+ case 100:
+ ipg_size = MLXBF_GIGE_100M_IPG_SIZE;
+ sgmii_mode = MLXBF_GIGE_100M_SGMII_MODE;
+ break;
+ case 10:
+ ipg_size = MLXBF_GIGE_10M_IPG_SIZE;
+ sgmii_mode = MLXBF_GIGE_10M_SGMII_MODE;
+ break;
+ default:
+ return;
+ }
+
+ val = readl(priv->plu_base + MLXBF_GIGE_PLU_TX_REG0);
+ val &= ~(MLXBF_GIGE_PLU_TX_IPG_SIZE_MASK | MLXBF_GIGE_PLU_TX_SGMII_MODE_MASK);
+ val |= FIELD_PREP(MLXBF_GIGE_PLU_TX_IPG_SIZE_MASK, ipg_size);
+ val |= FIELD_PREP(MLXBF_GIGE_PLU_TX_SGMII_MODE_MASK, sgmii_mode);
+ writel(val, priv->plu_base + MLXBF_GIGE_PLU_TX_REG0);
+
+ val = readl(priv->plu_base + MLXBF_GIGE_PLU_RX_REG0);
+ val &= ~MLXBF_GIGE_PLU_RX_SGMII_MODE_MASK;
+ val |= FIELD_PREP(MLXBF_GIGE_PLU_RX_SGMII_MODE_MASK, sgmii_mode);
+ writel(val, priv->plu_base + MLXBF_GIGE_PLU_RX_REG0);
+
+ priv->prev_speed = phydev->speed;
+ }
+
+ phy_print_status(phydev);
+}
+
+static void mlxbf_gige_bf2_set_phy_link_mode(struct phy_device *phydev)
+{
+ /* MAC only supports 1000T full duplex mode */
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_100baseT_Full_BIT);
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Full_BIT);
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+
+ /* Only symmetric pause with flow control enabled is supported so no
+ * need to negotiate pause.
+ */
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_Pause_BIT, phydev->advertising);
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->advertising);
+}
+
+static void mlxbf_gige_bf3_set_phy_link_mode(struct phy_device *phydev)
+{
+ /* MAC only supports full duplex mode */
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+ phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+
+ /* Only symmetric pause with flow control enabled is supported so no
+ * need to negotiate pause.
+ */
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_Pause_BIT, phydev->advertising);
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->advertising);
+}
+
+static struct mlxbf_gige_link_cfg mlxbf_gige_link_cfgs[] = {
+ [MLXBF_GIGE_VERSION_BF2] = {
+ .set_phy_link_mode = mlxbf_gige_bf2_set_phy_link_mode,
+ .adjust_link = mlxbf_gige_bf2_adjust_link,
+ .phy_mode = PHY_INTERFACE_MODE_GMII
+ },
+ [MLXBF_GIGE_VERSION_BF3] = {
+ .set_phy_link_mode = mlxbf_gige_bf3_set_phy_link_mode,
+ .adjust_link = mlxbf_gige_bf3_adjust_link,
+ .phy_mode = PHY_INTERFACE_MODE_SGMII
+ }
+};
+
static int mlxbf_gige_probe(struct platform_device *pdev)
{
struct phy_device *phydev;
@@ -359,25 +445,14 @@ static int mlxbf_gige_probe(struct platform_device *pdev)
phydev->irq = phy_irq;
err = phy_connect_direct(netdev, phydev,
- mlxbf_gige_adjust_link,
- PHY_INTERFACE_MODE_GMII);
+ mlxbf_gige_link_cfgs[priv->hw_version].adjust_link,
+ mlxbf_gige_link_cfgs[priv->hw_version].phy_mode);
if (err) {
dev_err(&pdev->dev, "Could not attach to PHY\n");
goto out;
}
- /* MAC only supports 1000T full duplex mode */
- phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
- phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_100baseT_Full_BIT);
- phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
- phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Full_BIT);
- phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
-
- /* Only symmetric pause with flow control enabled is supported so no
- * need to negotiate pause.
- */
- linkmode_clear_bit(ETHTOOL_LINK_MODE_Pause_BIT, phydev->advertising);
- linkmode_clear_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, phydev->advertising);
+ mlxbf_gige_link_cfgs[priv->hw_version].set_phy_link_mode(phydev);
/* Display information about attached PHY device */
phy_attached_info(phydev);
diff --git a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h
index 8d52dbef4adf..cd0973229c9b 100644
--- a/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h
+++ b/drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_regs.h
@@ -8,6 +8,8 @@
#ifndef __MLXBF_GIGE_REGS_H__
#define __MLXBF_GIGE_REGS_H__
+#include <linux/bitfield.h>
+
#define MLXBF_GIGE_VERSION 0x0000
#define MLXBF_GIGE_VERSION_BF2 0x0
#define MLXBF_GIGE_VERSION_BF3 0x1
@@ -78,4 +80,23 @@
*/
#define MLXBF_GIGE_MMIO_REG_SZ (MLXBF_GIGE_MAC_CFG + 8)
+#define MLXBF_GIGE_PLU_TX_REG0 0x80
+#define MLXBF_GIGE_PLU_TX_IPG_SIZE_MASK GENMASK(11, 0)
+#define MLXBF_GIGE_PLU_TX_SGMII_MODE_MASK GENMASK(15, 14)
+
+#define MLXBF_GIGE_PLU_RX_REG0 0x10
+#define MLXBF_GIGE_PLU_RX_SGMII_MODE_MASK GENMASK(25, 24)
+
+#define MLXBF_GIGE_1G_SGMII_MODE 0x0
+#define MLXBF_GIGE_10M_SGMII_MODE 0x1
+#define MLXBF_GIGE_100M_SGMII_MODE 0x2
+
+/* ipg_size default value for 1G is fixed by HW to 11 + End = 12.
+ * So for 100M it is 12 * 10 - 1 = 119
+ * For 10M, it is 12 * 100 - 1 = 1199
+ */
+#define MLXBF_GIGE_1G_IPG_SIZE 11
+#define MLXBF_GIGE_100M_IPG_SIZE 119
+#define MLXBF_GIGE_10M_IPG_SIZE 1199
+
#endif /* !defined(__MLXBF_GIGE_REGS_H__) */
--
2.30.1
Powered by blists - more mailing lists