| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ZFZLNLE567nhS6xs@nanopsycho>
Date: Sat, 6 May 2023 14:42:28 +0200
From: Jiri Pirko <jiri@...nulli.us>
To: Vadim Fedorenko <vadim.fedorenko@...ux.dev>
Cc: Vadim Fedorenko <vadfed@...a.com>, Jakub Kicinski <kuba@...nel.org>,
Arkadiusz Kubalewski <arkadiusz.kubalewski@...el.com>,
Jonathan Lemon <jonathan.lemon@...il.com>,
Paolo Abeni <pabeni@...hat.com>,
Milena Olech <milena.olech@...el.com>,
Michal Michalik <michal.michalik@...el.com>,
linux-arm-kernel@...ts.infradead.org, poros@...hat.com,
mschmidt@...hat.com, netdev@...r.kernel.org,
linux-clk@...r.kernel.org
Subject: Re: [RFC PATCH v7 6/8] ptp_ocp: implement DPLL ops
Fri, May 05, 2023 at 03:43:08PM CEST, vadim.fedorenko@...ux.dev wrote:
>On 04/05/2023 10:27, Jiri Pirko wrote:
>> Fri, Apr 28, 2023 at 02:20:07AM CEST, vadfed@...a.com wrote:
>> > From: Vadim Fedorenko <vadim.fedorenko@...ux.dev>
>> >
>> > Implement basic DPLL operations in ptp_ocp driver as the
>> > simplest example of using new subsystem.
>> >
>> > Signed-off-by: Vadim Fedorenko <vadim.fedorenko@...ux.dev>
>> > ---
>> > drivers/ptp/Kconfig | 1 +
>> > drivers/ptp/ptp_ocp.c | 327 +++++++++++++++++++++++++++++++++++-------
>> > 2 files changed, 276 insertions(+), 52 deletions(-)
>> >
>> > diff --git a/drivers/ptp/Kconfig b/drivers/ptp/Kconfig
>> > index b00201d81313..e3575c2e34dc 100644
>> > --- a/drivers/ptp/Kconfig
>> > +++ b/drivers/ptp/Kconfig
>> > @@ -177,6 +177,7 @@ config PTP_1588_CLOCK_OCP
>> > depends on COMMON_CLK
>> > select NET_DEVLINK
>> > select CRC16
>> > + select DPLL
>> > help
>> > This driver adds support for an OpenCompute time card.
>> >
>> > diff --git a/drivers/ptp/ptp_ocp.c b/drivers/ptp/ptp_ocp.c
>> > index 2b63f3487645..100e5da0aeb3 100644
>> > --- a/drivers/ptp/ptp_ocp.c
>> > +++ b/drivers/ptp/ptp_ocp.c
>> > @@ -23,6 +23,7 @@
>> > #include <linux/mtd/mtd.h>
>> > #include <linux/nvmem-consumer.h>
>> > #include <linux/crc16.h>
>> > +#include <linux/dpll.h>
>> >
>> > #define PCI_VENDOR_ID_FACEBOOK 0x1d9b
>> > #define PCI_DEVICE_ID_FACEBOOK_TIMECARD 0x0400
>> > @@ -261,12 +262,21 @@ enum ptp_ocp_sma_mode {
>> > SMA_MODE_OUT,
>> > };
>> >
>> > +static struct dpll_pin_frequency ptp_ocp_sma_freq[] = {
>>
>> const
>
>Forgot about this one, will change it.
>
>>
>> > + DPLL_PIN_FREQUENCY_1PPS,
>> > + DPLL_PIN_FREQUENCY_10MHZ,
>> > + DPLL_PIN_FREQUENCY_IRIG_B,
>> > + DPLL_PIN_FREQUENCY_DCF77,
>> > +};
>> > +
>> > struct ptp_ocp_sma_connector {
>> > enum ptp_ocp_sma_mode mode;
>> > bool fixed_fcn;
>> > bool fixed_dir;
>> > bool disabled;
>> > u8 default_fcn;
>> > + struct dpll_pin *dpll_pin;
>> > + struct dpll_pin_properties dpll_prop;
>> > };
>> >
>> > struct ocp_attr_group {
>> > @@ -295,6 +305,7 @@ struct ptp_ocp_serial_port {
>> >
>> > #define OCP_BOARD_ID_LEN 13
>> > #define OCP_SERIAL_LEN 6
>> > +#define OCP_SMA_NUM 4
>> >
>> > struct ptp_ocp {
>> > struct pci_dev *pdev;
>> > @@ -351,8 +362,9 @@ struct ptp_ocp {
>> > u32 ts_window_adjust;
>> > u64 fw_cap;
>> > struct ptp_ocp_signal signal[4];
>> > - struct ptp_ocp_sma_connector sma[4];
>> > + struct ptp_ocp_sma_connector sma[OCP_SMA_NUM];
>> > const struct ocp_sma_op *sma_op;
>> > + struct dpll_device *dpll;
>> > };
>> >
>> > #define OCP_REQ_TIMESTAMP BIT(0)
>> > @@ -836,6 +848,7 @@ static DEFINE_IDR(ptp_ocp_idr);
>> > struct ocp_selector {
>> > const char *name;
>> > int value;
>> > + u64 frequency;
>> > };
>> >
>> > static const struct ocp_selector ptp_ocp_clock[] = {
>> > @@ -856,31 +869,31 @@ static const struct ocp_selector ptp_ocp_clock[] = {
>> > #define SMA_SELECT_MASK GENMASK(14, 0)
>> >
>> > static const struct ocp_selector ptp_ocp_sma_in[] = {
>> > - { .name = "10Mhz", .value = 0x0000 },
>> > - { .name = "PPS1", .value = 0x0001 },
>> > - { .name = "PPS2", .value = 0x0002 },
>> > - { .name = "TS1", .value = 0x0004 },
>> > - { .name = "TS2", .value = 0x0008 },
>> > - { .name = "IRIG", .value = 0x0010 },
>> > - { .name = "DCF", .value = 0x0020 },
>> > - { .name = "TS3", .value = 0x0040 },
>> > - { .name = "TS4", .value = 0x0080 },
>> > - { .name = "FREQ1", .value = 0x0100 },
>> > - { .name = "FREQ2", .value = 0x0200 },
>> > - { .name = "FREQ3", .value = 0x0400 },
>> > - { .name = "FREQ4", .value = 0x0800 },
>> > - { .name = "None", .value = SMA_DISABLE },
>> > + { .name = "10Mhz", .value = 0x0000, .frequency = 10000000 },
>> > + { .name = "PPS1", .value = 0x0001, .frequency = 1 },
>> > + { .name = "PPS2", .value = 0x0002, .frequency = 1 },
>> > + { .name = "TS1", .value = 0x0004, .frequency = 0 },
>> > + { .name = "TS2", .value = 0x0008, .frequency = 0 },
>> > + { .name = "IRIG", .value = 0x0010, .frequency = 10000 },
>> > + { .name = "DCF", .value = 0x0020, .frequency = 77500 },
>> > + { .name = "TS3", .value = 0x0040, .frequency = 0 },
>> > + { .name = "TS4", .value = 0x0080, .frequency = 0 },
>> > + { .name = "FREQ1", .value = 0x0100, .frequency = 0 },
>> > + { .name = "FREQ2", .value = 0x0200, .frequency = 0 },
>> > + { .name = "FREQ3", .value = 0x0400, .frequency = 0 },
>> > + { .name = "FREQ4", .value = 0x0800, .frequency = 0 },
>> > + { .name = "None", .value = SMA_DISABLE, .frequency = 0 },
>> > { }
>> > };
>> >
>> > static const struct ocp_selector ptp_ocp_sma_out[] = {
>> > - { .name = "10Mhz", .value = 0x0000 },
>> > - { .name = "PHC", .value = 0x0001 },
>> > - { .name = "MAC", .value = 0x0002 },
>> > - { .name = "GNSS1", .value = 0x0004 },
>> > - { .name = "GNSS2", .value = 0x0008 },
>> > - { .name = "IRIG", .value = 0x0010 },
>> > - { .name = "DCF", .value = 0x0020 },
>> > + { .name = "10Mhz", .value = 0x0000, .frequency = 10000000 },
>> > + { .name = "PHC", .value = 0x0001, .frequency = 1 },
>> > + { .name = "MAC", .value = 0x0002, .frequency = 1 },
>> > + { .name = "GNSS1", .value = 0x0004, .frequency = 1 },
>> > + { .name = "GNSS2", .value = 0x0008, .frequency = 1 },
>> > + { .name = "IRIG", .value = 0x0010, .frequency = 10000 },
>> > + { .name = "DCF", .value = 0x0020, .frequency = 77000 },
>> > { .name = "GEN1", .value = 0x0040 },
>> > { .name = "GEN2", .value = 0x0080 },
>> > { .name = "GEN3", .value = 0x0100 },
>> > @@ -891,15 +904,15 @@ static const struct ocp_selector ptp_ocp_sma_out[] = {
>> > };
>> >
>> > static const struct ocp_selector ptp_ocp_art_sma_in[] = {
>> > - { .name = "PPS1", .value = 0x0001 },
>> > - { .name = "10Mhz", .value = 0x0008 },
>> > + { .name = "PPS1", .value = 0x0001, .frequency = 1 },
>> > + { .name = "10Mhz", .value = 0x0008, .frequency = 1000000 },
>> > { }
>> > };
>> >
>> > static const struct ocp_selector ptp_ocp_art_sma_out[] = {
>> > - { .name = "PHC", .value = 0x0002 },
>> > - { .name = "GNSS", .value = 0x0004 },
>> > - { .name = "10Mhz", .value = 0x0010 },
>> > + { .name = "PHC", .value = 0x0002, .frequency = 1 },
>> > + { .name = "GNSS", .value = 0x0004, .frequency = 1 },
>> > + { .name = "10Mhz", .value = 0x0010, .frequency = 10000000 },
>> > { }
>> > };
>> >
>> > @@ -2283,22 +2296,34 @@ ptp_ocp_sma_fb_set_inputs(struct ptp_ocp *bp, int sma_nr, u32 val)
>> > static void
>> > ptp_ocp_sma_fb_init(struct ptp_ocp *bp)
>> > {
>> > + struct dpll_pin_properties prop = {
>>
>> Why don't you have this as static const outside the function?
>>
>
>Because I'm changing label string for every pin. I cannot change it in
>the const object.
No you don't. You just copy prop to bp->sma[i].dpll_prop. Prop does not
change.
>
>>
>> > + .label = NULL,
>>
>> Pointless init.
>
>Agree
>
>> > + .type = DPLL_PIN_TYPE_EXT,
>> > + .capabilities = DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE,
>> > + .freq_supported_num = ARRAY_SIZE(ptp_ocp_sma_freq),
>> > + .freq_supported = ptp_ocp_sma_freq,
>> > +
>> > + };
>> > u32 reg;
>> > int i;
>> >
>> > /* defaults */
>> > + for (i = 0; i < OCP_SMA_NUM; i++) {
>> > + bp->sma[i].default_fcn = i & 1;
>> > + bp->sma[i].dpll_prop = prop;
>> > + bp->sma[i].dpll_prop.label = bp->ptp_info.pin_config[i].name;
>> > + }
>> > bp->sma[0].mode = SMA_MODE_IN;
>> > bp->sma[1].mode = SMA_MODE_IN;
>> > bp->sma[2].mode = SMA_MODE_OUT;
>> > bp->sma[3].mode = SMA_MODE_OUT;
>> > - for (i = 0; i < 4; i++)
>> > - bp->sma[i].default_fcn = i & 1;
>> > -
>> > /* If no SMA1 map, the pin functions and directions are fixed. */
>> > if (!bp->sma_map1) {
>> > - for (i = 0; i < 4; i++) {
>> > + for (i = 0; i < OCP_SMA_NUM; i++) {
>> > bp->sma[i].fixed_fcn = true;
>> > bp->sma[i].fixed_dir = true;
>> > + bp->sma[1].dpll_prop.capabilities &=
>> > + ~DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE;
>> > }
>> > return;
>> > }
>> > @@ -2308,7 +2333,7 @@ ptp_ocp_sma_fb_init(struct ptp_ocp *bp)
>> > */
>> > reg = ioread32(&bp->sma_map2->gpio2);
>> > if (reg == 0xffffffff) {
>> > - for (i = 0; i < 4; i++)
>> > + for (i = 0; i < OCP_SMA_NUM; i++)
>> > bp->sma[i].fixed_dir = true;
>> > } else {
>> > reg = ioread32(&bp->sma_map1->gpio1);
>> > @@ -2330,7 +2355,7 @@ static const struct ocp_sma_op ocp_fb_sma_op = {
>> > };
>> >
>> > static int
>> > -ptp_ocp_fb_set_pins(struct ptp_ocp *bp)
>> > +ptp_ocp_set_pins(struct ptp_ocp *bp)
>> > {
>> > struct ptp_pin_desc *config;
>> > int i;
>> > @@ -2397,16 +2422,16 @@ ptp_ocp_fb_board_init(struct ptp_ocp *bp, struct ocp_resource *r)
>> >
>> > ptp_ocp_tod_init(bp);
>> > ptp_ocp_nmea_out_init(bp);
>> > - ptp_ocp_sma_init(bp);
>> > ptp_ocp_signal_init(bp);
>> >
>> > err = ptp_ocp_attr_group_add(bp, fb_timecard_groups);
>> > if (err)
>> > return err;
>> >
>> > - err = ptp_ocp_fb_set_pins(bp);
>> > + err = ptp_ocp_set_pins(bp);
>> > if (err)
>> > return err;
>> > + ptp_ocp_sma_init(bp);
>> >
>> > return ptp_ocp_init_clock(bp);
>> > }
>> > @@ -2446,6 +2471,14 @@ ptp_ocp_register_resources(struct ptp_ocp *bp, kernel_ulong_t driver_data)
>> > static void
>> > ptp_ocp_art_sma_init(struct ptp_ocp *bp)
>> > {
>> > + struct dpll_pin_properties prop = {
>> > + .label = NULL,
>> > + .type = DPLL_PIN_TYPE_EXT,
>> > + .capabilities = 0,
>>
>> Same comment as to the similar prop struct above. Plus another pointless
>> init here.
>>
>
>Will remove pointless init.
>
>>
>> > + .freq_supported_num = ARRAY_SIZE(ptp_ocp_sma_freq),
>> > + .freq_supported = ptp_ocp_sma_freq,
>> > +
>> > + };
>> > u32 reg;
>> > int i;
>> >
>> > @@ -2460,16 +2493,16 @@ ptp_ocp_art_sma_init(struct ptp_ocp *bp)
>> > bp->sma[2].default_fcn = 0x10; /* OUT: 10Mhz */
>> > bp->sma[3].default_fcn = 0x02; /* OUT: PHC */
>> >
>> > - /* If no SMA map, the pin functions and directions are fixed. */
>> > - if (!bp->art_sma) {
>> > - for (i = 0; i < 4; i++) {
>> > +
>> > + for (i = 0; i < OCP_SMA_NUM; i++) {
>> > + /* If no SMA map, the pin functions and directions are fixed. */
>> > + bp->sma[i].dpll_prop = prop;
>> > + bp->sma[i].dpll_prop.label = bp->ptp_info.pin_config[i].name;
>> > + if (!bp->art_sma) {
>> > bp->sma[i].fixed_fcn = true;
>> > bp->sma[i].fixed_dir = true;
>> > + continue;
>> > }
>> > - return;
>> > - }
>> > -
>> > - for (i = 0; i < 4; i++) {
>> > reg = ioread32(&bp->art_sma->map[i].gpio);
>> >
>> > switch (reg & 0xff) {
>> > @@ -2480,9 +2513,13 @@ ptp_ocp_art_sma_init(struct ptp_ocp *bp)
>> > case 1:
>> > case 8:
>> > bp->sma[i].mode = SMA_MODE_IN;
>> > + bp->sma[i].dpll_prop.capabilities =
>> > + DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE;
>> > break;
>> > default:
>> > bp->sma[i].mode = SMA_MODE_OUT;
>> > + bp->sma[i].dpll_prop.capabilities =
>> > + DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE;
>> > break;
>> > }
>> > }
>> > @@ -2549,6 +2586,9 @@ ptp_ocp_art_board_init(struct ptp_ocp *bp, struct ocp_resource *r)
>> > /* Enable MAC serial port during initialisation */
>> > iowrite32(1, &bp->board_config->mro50_serial_activate);
>> >
>> > + err = ptp_ocp_set_pins(bp);
>> > + if (err)
>> > + return err;
>> > ptp_ocp_sma_init(bp);
>> >
>> > err = ptp_ocp_attr_group_add(bp, art_timecard_groups);
>> > @@ -2690,16 +2730,9 @@ sma4_show(struct device *dev, struct device_attribute *attr, char *buf)
>> > }
>> >
>> > static int
>> > -ptp_ocp_sma_store(struct ptp_ocp *bp, const char *buf, int sma_nr)
>> > +ptp_ocp_sma_store_val(struct ptp_ocp *bp, int val, enum ptp_ocp_sma_mode mode, int sma_nr)
>> > {
>> > struct ptp_ocp_sma_connector *sma = &bp->sma[sma_nr - 1];
>> > - enum ptp_ocp_sma_mode mode;
>> > - int val;
>> > -
>> > - mode = sma->mode;
>> > - val = sma_parse_inputs(bp->sma_op->tbl, buf, &mode);
>> > - if (val < 0)
>> > - return val;
>> >
>> > if (sma->fixed_dir && (mode != sma->mode || val & SMA_DISABLE))
>> > return -EOPNOTSUPP;
>> > @@ -2734,6 +2767,20 @@ ptp_ocp_sma_store(struct ptp_ocp *bp, const char *buf, int sma_nr)
>> > return val;
>> > }
>> >
>> > +static int
>> > +ptp_ocp_sma_store(struct ptp_ocp *bp, const char *buf, int sma_nr)
>> > +{
>> > + struct ptp_ocp_sma_connector *sma = &bp->sma[sma_nr - 1];
>> > + enum ptp_ocp_sma_mode mode;
>> > + int val;
>> > +
>> > + mode = sma->mode;
>> > + val = sma_parse_inputs(bp->sma_op->tbl, buf, &mode);
>> > + if (val < 0)
>> > + return val;
>> > + return ptp_ocp_sma_store_val(bp, val, mode, sma_nr);
>> > +}
>> > +
>> > static ssize_t
>> > sma1_store(struct device *dev, struct device_attribute *attr,
>> > const char *buf, size_t count)
>> > @@ -4172,12 +4219,148 @@ ptp_ocp_detach(struct ptp_ocp *bp)
>> > device_unregister(&bp->dev);
>> > }
>> >
>> > +static int ptp_ocp_dpll_lock_status_get(const struct dpll_device *dpll,
>> > + void *priv,
>> > + enum dpll_lock_status *status,
>> > + struct netlink_ext_ack *extack)
>> > +{
>> > + struct ptp_ocp *bp = priv;
>> > + int sync;
>> > +
>> > + sync = ioread32(&bp->reg->status) & OCP_STATUS_IN_SYNC;
>> > + *status = sync ? DPLL_LOCK_STATUS_LOCKED : DPLL_LOCK_STATUS_UNLOCKED;
>>
>> Does your device support event delivery in case of the status change?
>> ice and mlx5 drivers do poll for changes in this area anyway. It's a
>> part of this patchset. You should do the same if your device does
>> not support events.
>>
>> Could you please implement notifications using
>> dpll_device_notify() for status change and dpll_pin_notify() for pin
>> state change?
>>
>
>We are working on implementation of interrupt-based notifications, that's why
>I didn't implement polling code. Hopefully it will be ready before the
>non-RFC patchset submission.
Do polling implementation if not and replace by interrupt driver later.
Point is, there have to be notifications from day 1.
>
>>
>> > +
>> > + return 0;
>> > +}
>> > +
>> > +static int ptp_ocp_dpll_source_idx_get(const struct dpll_device *dpll,
>> > + void *priv, u32 *idx,
>> > + struct netlink_ext_ack *extack)
>> > +{
>> > + struct ptp_ocp *bp = priv;
>> > +
>> > + if (bp->pps_select) {
>> > + *idx = ioread32(&bp->pps_select->gpio1);
>> > + return 0;
>> > + }
>> > + return -EINVAL;
>> > +}
>> > +
>> > +static int ptp_ocp_dpll_mode_get(const struct dpll_device *dpll, void *priv,
>> > + u32 *mode, struct netlink_ext_ack *extack)
>> > +{
>> > + *mode = DPLL_MODE_AUTOMATIC;
>> > + return 0;
>> > +}
>> > +
>> > +static bool ptp_ocp_dpll_mode_supported(const struct dpll_device *dpll,
>> > + void *priv, const enum dpll_mode mode,
>> > + struct netlink_ext_ack *extack)
>> > +{
>> > + return mode == DPLL_MODE_AUTOMATIC;
>> > +}
>> > +
>> > +static int ptp_ocp_dpll_direction_get(const struct dpll_pin *pin,
>> > + void *pin_priv,
>> > + const struct dpll_device *dpll,
>> > + void *priv,
>> > + enum dpll_pin_direction *direction,
>> > + struct netlink_ext_ack *extack)
>> > +{
>> > + struct ptp_ocp_sma_connector *sma = pin_priv;
>> > +
>> > + *direction = sma->mode == SMA_MODE_IN ?
>> > + DPLL_PIN_DIRECTION_SOURCE :
>> > + DPLL_PIN_DIRECTION_OUTPUT;
>> > + return 0;
>> > +}
>> > +
>> > +static int ptp_ocp_dpll_direction_set(const struct dpll_pin *pin,
>> > + void *pin_priv,
>> > + const struct dpll_device *dpll,
>> > + void *dpll_priv,
>> > + enum dpll_pin_direction direction,
>> > + struct netlink_ext_ack *extack)
>> > +{
>> > + struct ptp_ocp_sma_connector *sma = pin_priv;
>> > + struct ptp_ocp *bp = dpll_priv;
>> > + enum ptp_ocp_sma_mode mode;
>> > + int sma_nr = (sma - bp->sma);
>> > +
>> > + if (sma->fixed_dir)
>>
>> I believe that this is a pointless check as DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE
>> is not set and therefore the check in dpll_pin_direction_set() will be
>> true and -EOPNOTSUPP will be returned from there.
>> Remove this.
>
>Yep, will do it.
>
>>
>> > + return -EOPNOTSUPP;
>> > + mode = direction == DPLL_PIN_DIRECTION_SOURCE ?
>> > + SMA_MODE_IN : SMA_MODE_OUT;
>> > + return ptp_ocp_sma_store_val(bp, 0, mode, sma_nr);
>>
>> You need sma_nr just here. Why can't you change ptp_ocp_sma_store_val()
>> to accept struct ptp_ocp_sma_connector * instead avoiding the need for
>> tne sma_nr completely?
>>
>
>I wanted to add minimal changes to the driver, I will consider changing this
>as a separate net-next patch.
Hmm, you do change ptp_ocp_sma_store_val() here anyway. Could be an
extra patch in this patchset before this one if you want to have it
separate.
>
>>
>> > +}
>> > +
>> > +static int ptp_ocp_dpll_frequency_set(const struct dpll_pin *pin,
>> > + void *pin_priv,
>> > + const struct dpll_device *dpll,
>> > + void *dpll_priv, u64 frequency,
>> > + struct netlink_ext_ack *extack)
>> > +{
>> > + struct ptp_ocp_sma_connector *sma = pin_priv;
>> > + struct ptp_ocp *bp = dpll_priv;
>> > + const struct ocp_selector *tbl;
>> > + int sma_nr = (sma - bp->sma);
>> > + int val, i;
>> > +
>> > + if (sma->fixed_fcn)
>>
>> In that case, just fill up a single frequency in the properties,
>> avoid this check-fail and let the dpll core handle it.
>>
>
>Makes sense.
>
>>
>> > + return -EOPNOTSUPP;
>> > +
>> > + tbl = bp->sma_op->tbl[sma->mode];
>> > + for (i = 0; tbl[i].name; i++)
>> > + if (tbl[i].frequency == frequency)
>> > + return ptp_ocp_sma_store_val(bp, val, sma->mode, sma_nr);
>> > + return -EINVAL;
>> > +}
>> > +
>> > +static int ptp_ocp_dpll_frequency_get(const struct dpll_pin *pin,
>> > + void *pin_priv,
>> > + const struct dpll_device *dpll,
>> > + void *dpll_priv, u64 *frequency,
>> > + struct netlink_ext_ack *extack)
>> > +{
>> > + struct ptp_ocp_sma_connector *sma = pin_priv;
>> > + struct ptp_ocp *bp = dpll_priv;
>> > + const struct ocp_selector *tbl;
>> > + int sma_nr = (sma - bp->sma);
>>
>> 1) void "()"s here.
>> 2) why don't you fill the sma_nr in struct ptp_ocp_sma_connector to make
>> this easier to follow? IDK, just a suggestion, take or leave.
>>
>> Same applies to the the rest of similar occurances above.
>>
>
>Will do it, yes.
>
>>
>> > + u32 val;
>> > + int i;
>> > +
>> > + val = bp->sma_op->get(bp, sma_nr);
>> > + tbl = bp->sma_op->tbl[sma->mode];
>> > + for (i = 0; tbl[i].name; i++)
>> > + if (val == tbl[i].value) {
>> > + *frequency = tbl[i].frequency;
>> > + return 0;
>> > + }
>> > +
>> > + return -EINVAL;
>> > +}
>> > +
>> > +static const struct dpll_device_ops dpll_ops = {
>> > + .lock_status_get = ptp_ocp_dpll_lock_status_get,
>> > + .source_pin_idx_get = ptp_ocp_dpll_source_idx_get,
>>
>> This op is a leftover, in dpll core it is not called. This was removed
>> and agreed that drivers should implement state_on_dpll_get() op for pins
>> to see which one is connected.
>>
>> Please fix here and remove the leftover from DPLL patch #2 as well.
Did you miss this by any chance?
>>
>>
>> > + .mode_get = ptp_ocp_dpll_mode_get,
>> > + .mode_supported = ptp_ocp_dpll_mode_supported,
>> > +};
>> > +
>> > +static const struct dpll_pin_ops dpll_pins_ops = {
>> > + .frequency_get = ptp_ocp_dpll_frequency_get,
>> > + .frequency_set = ptp_ocp_dpll_frequency_set,
>> > + .direction_get = ptp_ocp_dpll_direction_get,
>> > + .direction_set = ptp_ocp_dpll_direction_set,
>> > +};
>> > +
>> > static int
>> > ptp_ocp_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>> > {
>> > struct devlink *devlink;
>> > struct ptp_ocp *bp;
>> > - int err;
>> > + int err, i;
>> > + u64 clkid;
>> >
>> > devlink = devlink_alloc(&ptp_ocp_devlink_ops, sizeof(*bp), &pdev->dev);
>> > if (!devlink) {
>> > @@ -4227,8 +4410,39 @@ ptp_ocp_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>> >
>> > ptp_ocp_info(bp);
>> > devlink_register(devlink);
>> > - return 0;
>> >
>> > + clkid = pci_get_dsn(pdev);
>> > + bp->dpll = dpll_device_get(clkid, 0, THIS_MODULE);
>>
>> I suggested this the last time, but again: Could you please:
>> 1) rename dpll_device_get to __dpll_device_get
>> 2) introduce dpll_device_get as a macro filling up THIS_MODULE
>>
>> Then drivers will just call always:
>> bp->dpll = dpll_device_get(clkid, 0);
>> and the macro will fillup the module automatically.
>>
>> Please do the same for dpll_pin_get()
>>
>
>Not sure why I have missed this part, but sure will do it.
Awesome.
>
>>
>> > + if (IS_ERR(bp->dpll)) {
>> > + dev_err(&pdev->dev, "dpll_device_alloc failed\n");
>>
>> You need to fix your error path to call devlink_unregister() in this
>> case.
>>
>>
>> > + goto out;
>> > + }
>> > +
>> > + err = dpll_device_register(bp->dpll, DPLL_TYPE_PPS, &dpll_ops, bp, &pdev->dev);
>> > + if (err)
>>
>> You need to fix your error path to call dpll_device_put() in this
>> case.
>>
>
>Ok, I'll re-check and update the error path for the next version.
>
>>
>> > + goto out;
>> > +
>> > + for (i = 0; i < OCP_SMA_NUM; i++) {
>> > + bp->sma[i].dpll_pin = dpll_pin_get(clkid, i, THIS_MODULE, &bp->sma[i].dpll_prop);
>> > + if (IS_ERR(bp->sma[i].dpll_pin))
>> > + goto out_dpll;
>> > +
>> > + err = dpll_pin_register(bp->dpll, bp->sma[i].dpll_pin, &dpll_pins_ops,
>> > + &bp->sma[i], NULL);
>> > + if (err) {
>> > + dpll_pin_put(bp->sma[i].dpll_pin);
>> > + goto out_dpll;
>> > + }
>> > + }
>> > +
>> > + return 0;
>> > +out_dpll:
>> > + while (i) {
>> > + --i;
>>
>> while (i--) {
>> ?
>>
>> > + dpll_pin_unregister(bp->dpll, bp->sma[i].dpll_pin, &dpll_pins_ops, &bp->sma[i]);
>> > + dpll_pin_put(bp->sma[i].dpll_pin);
>> > + }
>> > + dpll_device_put(bp->dpll);
>> > out:
>> > ptp_ocp_detach(bp);
>> > out_disable:
>> > @@ -4243,7 +4457,16 @@ ptp_ocp_remove(struct pci_dev *pdev)
>> > {
>> > struct ptp_ocp *bp = pci_get_drvdata(pdev);
>> > struct devlink *devlink = priv_to_devlink(bp);
>> > + int i;
>> >
>> > + for (i = 0; i < OCP_SMA_NUM; i++) {
>> > + if (bp->sma[i].dpll_pin) {
>>
>> Remove this pointless check. It is always true.
>
>Agree.
>
>>
>>
>> > + dpll_pin_unregister(bp->dpll, bp->sma[i].dpll_pin, &dpll_pins_ops, bp);
>> > + dpll_pin_put(bp->sma[i].dpll_pin);
>> > + }
>> > + }
>> > + dpll_device_unregister(bp->dpll, &dpll_ops, bp);
>> > + dpll_device_put(bp->dpll);
>> > devlink_unregister(devlink);
>> > ptp_ocp_detach(bp);
>> > pci_disable_device(pdev);
>> > --
>> > 2.34.1
>> >
>
Powered by blists - more mailing lists