lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
Open Source and information security mailing list archives
| ||
|
Message-Id: <20230518092913.977705-2-o.rempel@pengutronix.de> Date: Thu, 18 May 2023 11:29:12 +0200 From: Oleksij Rempel <o.rempel@...gutronix.de> To: "David S. Miller" <davem@...emloft.net>, Andrew Lunn <andrew@...n.ch>, Eric Dumazet <edumazet@...gle.com>, Florian Fainelli <f.fainelli@...il.com>, Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>, Vladimir Oltean <olteanv@...il.com>, Woojung Huh <woojung.huh@...rochip.com>, Arun Ramadoss <arun.ramadoss@...rochip.com>, "Russell King (Oracle)" <linux@...linux.org.uk> Cc: Oleksij Rempel <o.rempel@...gutronix.de>, kernel@...gutronix.de, linux-kernel@...r.kernel.org, netdev@...r.kernel.org, UNGLinuxDriver@...rochip.com Subject: [PATCH net-next v3 1/2] net: dsa: microchip: ksz8: Make flow control, speed, and duplex on CPU port configurable Allow flow control, speed, and duplex settings on the CPU port to be configurable. Previously, the speed and duplex relied on default switch values, which limited flexibility. Additionally, flow control was hardcoded and only functional in duplex mode. This update enhances the configurability of these parameters. Signed-off-by: Oleksij Rempel <o.rempel@...gutronix.de> --- drivers/net/dsa/microchip/ksz8.h | 4 ++ drivers/net/dsa/microchip/ksz8795.c | 51 +++++++++++++++++++++++++- drivers/net/dsa/microchip/ksz_common.c | 1 + 3 files changed, 54 insertions(+), 2 deletions(-) diff --git a/drivers/net/dsa/microchip/ksz8.h b/drivers/net/dsa/microchip/ksz8.h index e68465fdf6b9..ec02baca726f 100644 --- a/drivers/net/dsa/microchip/ksz8.h +++ b/drivers/net/dsa/microchip/ksz8.h @@ -58,5 +58,9 @@ int ksz8_switch_detect(struct ksz_device *dev); int ksz8_switch_init(struct ksz_device *dev); void ksz8_switch_exit(struct ksz_device *dev); int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu); +void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port, + unsigned int mode, phy_interface_t interface, + struct phy_device *phydev, int speed, int duplex, + bool tx_pause, bool rx_pause); #endif diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c index f56fca1b1a22..9cfe343d2214 100644 --- a/drivers/net/dsa/microchip/ksz8795.c +++ b/drivers/net/dsa/microchip/ksz8795.c @@ -1371,6 +1371,55 @@ void ksz8_config_cpu_port(struct dsa_switch *ds) } } +/** + * ksz8_upstream_link_up - Configures the CPU/upstream port of the switch. + * @dev: The KSZ device instance. + * @port: The port number to configure. + * @speed: The desired link speed. + * @duplex: The desired duplex mode. + * @tx_pause: If true, enables transmit pause. + * @rx_pause: If true, enables receive pause. + * + * Description: + * The function configures flow control and speed settings for the CPU/upstream + * port of the switch based on the desired settings, current duplex mode, and + * speed. + */ +static void ksz8_upstream_link_up(struct ksz_device *dev, int port, int speed, + int duplex, bool tx_pause, bool rx_pause) +{ + u8 ctrl = 0; + + /* SW_FLOW_CTRL, SW_HALF_DUPLEX, and SW_10_MBIT bits are bootstrappable. + * They can have different values depending on your board setup. + */ + if (duplex) { + if (tx_pause || rx_pause) + ctrl |= SW_FLOW_CTRL; + } else { + ctrl |= SW_HALF_DUPLEX; + } + + /* This hardware only supports SPEED_10 and SPEED_100. For SPEED_10 + * we need to set the SW_10_MBIT bit. Otherwise, we can leave it 0. + */ + if (speed == SPEED_10) + ctrl |= SW_10_MBIT; + + ksz_rmw8(dev, REG_SW_CTRL_4, SW_HALF_DUPLEX | SW_FLOW_CTRL | + SW_10_MBIT, ctrl); +} + +void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port, + unsigned int mode, phy_interface_t interface, + struct phy_device *phydev, int speed, int duplex, + bool tx_pause, bool rx_pause) +{ + if (dsa_is_upstream_port(dev->ds, port)) + ksz8_upstream_link_up(dev, port, speed, duplex, tx_pause, + rx_pause); +} + static int ksz8_handle_global_errata(struct dsa_switch *ds) { struct ksz_device *dev = ds->priv; @@ -1419,8 +1468,6 @@ int ksz8_setup(struct dsa_switch *ds) */ ds->vlan_filtering_is_global = true; - ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true); - /* Enable automatic fast aging when link changed detected. */ ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true); diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c index a4428be5f483..6e19ad70c671 100644 --- a/drivers/net/dsa/microchip/ksz_common.c +++ b/drivers/net/dsa/microchip/ksz_common.c @@ -210,6 +210,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = { .mirror_add = ksz8_port_mirror_add, .mirror_del = ksz8_port_mirror_del, .get_caps = ksz8_get_caps, + .phylink_mac_link_up = ksz8_phylink_mac_link_up, .config_cpu_port = ksz8_config_cpu_port, .enable_stp_addr = ksz8_enable_stp_addr, .reset = ksz8_reset_switch, -- 2.39.2
Powered by blists - more mailing lists