netdev - [PATCH net-next v3 4/6] net: phy: microchip_t1s: fix reset complete status handling

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20230524144539.62618-5-Parthiban.Veerasooran@microchip.com>
Date: Wed, 24 May 2023 20:15:37 +0530
From: Parthiban Veerasooran <Parthiban.Veerasooran@...rochip.com>
To: <andrew@...n.ch>, <hkallweit1@...il.com>, <linux@...linux.org.uk>,
	<davem@...emloft.net>, <edumazet@...gle.com>, <kuba@...nel.org>,
	<pabeni@...hat.com>, <netdev@...r.kernel.org>,
	<linux-kernel@...r.kernel.org>, <ramon.nordin.rodriguez@...roamp.se>
CC: <horatiu.vultur@...rochip.com>, <Woojung.Huh@...rochip.com>,
	<Nicolas.Ferre@...rochip.com>, <Thorsten.Kummermehr@...rochip.com>,
	"Parthiban Veerasooran" <Parthiban.Veerasooran@...rochip.com>
Subject: [PATCH net-next v3 4/6] net: phy: microchip_t1s: fix reset complete status handling

As per the datasheet DS-LAN8670-1-2-60001573C.pdf, the Reset Complete
status bit in the STS2 register has to be checked before proceeding to
the initial configuration. Reading STS2 register will also clear the
Reset Complete interrupt which is non-maskable.

Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@...rochip.com>
---
 drivers/net/phy/microchip_t1s.c | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/drivers/net/phy/microchip_t1s.c b/drivers/net/phy/microchip_t1s.c
index 8f29d9802131..05a88b561993 100644
--- a/drivers/net/phy/microchip_t1s.c
+++ b/drivers/net/phy/microchip_t1s.c
@@ -14,6 +14,9 @@
 
 #define LAN867X_REG_IRQ_1_CTL 0x001C
 #define LAN867X_REG_IRQ_2_CTL 0x001D
+#define LAN867X_REG_STS2 0x0019
+
+#define LAN867x_RESET_COMPLETE_STS BIT(11)
 
 /* The arrays below are pulled from the following table from AN1699
  * Access MMD Address Value Mask
@@ -65,6 +68,27 @@ static int lan867x_revb1_config_init(struct phy_device *phydev)
 
 	int err;
 
+	/* Read STS2 register and check for the Reset Complete status to do the
+	 * init configuration. If the Reset Complete is not set, wait for 5us
+	 * and then read STS2 register again and check for Reset Complete status.
+	 * Still if it is failed then declare PHY reset error or else proceed
+	 * for the PHY initial register configuration.
+	 */
+	err = phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_STS2);
+	if (err < 0)
+		return err;
+
+	if (!(err & LAN867x_RESET_COMPLETE_STS)) {
+		udelay(5);
+		err = phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_STS2);
+		if (err < 0)
+			return err;
+		if (!(err & LAN867x_RESET_COMPLETE_STS)) {
+			phydev_err(phydev, "PHY reset failed\n");
+			return -ENODEV;
+		}
+	}
+
 	/* Read-Modified Write Pseudocode (from AN1699)
 	 * current_val = read_register(mmd, addr) // Read current register value
 	 * new_val = current_val AND (NOT mask) // Clear bit fields to be written
-- 
2.34.1