| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Thu, 22 Jun 2023 14:03:32 -0500
From: Nick Child <nnac123@...ux.ibm.com>
To: netdev@...r.kernel.org
Cc: haren@...ux.ibm.com, ricklind@...ibm.com,
Nick Child <nnac123@...ux.ibm.com>
Subject: [PATCH net] ibmvnic: Do not reset dql stats on NON_FATAL err
All ibmvnic resets, make a call to netdev_tx_reset_queue() when
re-opening the device. netdev_tx_reset_queue() resets the num_queued
and num_completed byte counters. These stats are used in Byte Queue
Limit (BQL) algorithms. The difference between these two stats tracks
the number of bytes currently sitting on the physical NIC. ibmvnic
increases the number of queued bytes though calls to
netdev_tx_sent_queue() in the drivers xmit function. When, VIOS reports
that it is done transmitting bytes, the ibmvnic device increases the
number of completed bytes through calls to netdev_tx_completed_queue().
It is important to note that the driver batches its transmit calls and
num_queued is increased every time that an skb is added to the next
batch, not necessarily when the batch is sent to VIOS for transmission.
Unlike other reset types, a NON FATAL reset will not flush the sub crq
tx buffers. Therefore, it is possible for the batched skb array to be
partially full. So if there is call to netdev_tx_reset_queue() when
re-opening the device, the value of num_queued (0) would not account
for the skb's that are currently batched. Eventually, when the batch
is sent to VIOS, the call to netdev_tx_completed_queue() would increase
num_completed to a value greater than the num_queued. This causes a
BUG_ON crash:
ibmvnic 30000002: Firmware reports error, cause: adapter problem.
Starting recovery...
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:27!
Oops: Exception in kernel mode, sig: 5
[....]
NIP dql_completed+0x28/0x1c0
LR ibmvnic_complete_tx.isra.0+0x23c/0x420 [ibmvnic]
Call Trace:
ibmvnic_complete_tx.isra.0+0x3f8/0x420 [ibmvnic] (unreliable)
ibmvnic_interrupt_tx+0x40/0x70 [ibmvnic]
__handle_irq_event_percpu+0x98/0x270
---[ end trace ]---
Therefore, do not reset the dql stats when performing a NON_FATAL reset.
Simply clearing the queues off bit is sufficient.
Fixes: 0d973388185d ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Signed-off-by: Nick Child <nnac123@...ux.ibm.com>
---
drivers/net/ethernet/ibm/ibmvnic.c | 13 ++++++++++++-
1 file changed, 12 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/ibm/ibmvnic.c b/drivers/net/ethernet/ibm/ibmvnic.c
index c63d3ec9d328..5523ab52ff2b 100644
--- a/drivers/net/ethernet/ibm/ibmvnic.c
+++ b/drivers/net/ethernet/ibm/ibmvnic.c
@@ -1816,7 +1816,18 @@ static int __ibmvnic_open(struct net_device *netdev)
if (prev_state == VNIC_CLOSED)
enable_irq(adapter->tx_scrq[i]->irq);
enable_scrq_irq(adapter, adapter->tx_scrq[i]);
- netdev_tx_reset_queue(netdev_get_tx_queue(netdev, i));
+ /* netdev_tx_reset_queue will reset dql stats and set the stacks
+ * flag for queue status. During NON_FATAL resets, just
+ * clear the bit, don't reset the stats because there could
+ * be batched skb's waiting to be sent. If we reset dql stats,
+ * we risk num_completed being greater than num_queued.
+ * This will cause a BUG_ON in dql_completed().
+ */
+ if (adapter->reset_reason == VNIC_RESET_NON_FATAL)
+ clear_bit(__QUEUE_STATE_STACK_XOFF,
+ &netdev_get_tx_queue(netdev, i)->state);
+ else
+ netdev_tx_reset_queue(netdev_get_tx_queue(netdev, i));
}
rc = set_link_state(adapter, IBMVNIC_LOGICAL_LNK_UP);
--
2.31.1
Powered by blists - more mailing lists