| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAJhJPsXHuMBAHqsg5rSVf5Ow_Rsgy2Zp-PNrLXWTeVSY3N08Aw@mail.gmail.com>
Date: Fri, 18 Aug 2023 20:37:27 +0800
From: Keguang Zhang <keguang.zhang@...il.com>
To: Serge Semin <fancer.lancer@...il.com>
Cc: netdev@...r.kernel.org, devicetree@...r.kernel.org,
linux-mips@...r.kernel.org, linux-kernel@...r.kernel.org,
Lee Jones <lee@...nel.org>, Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, Conor Dooley <conor+dt@...nel.org>,
"David S . Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
Thomas Bogendoerfer <tsbogend@...ha.franken.de>, Giuseppe Cavallaro <peppe.cavallaro@...com>,
Alexandre Torgue <alexandre.torgue@...s.st.com>, Jose Abreu <joabreu@...opsys.com>,
Serge Semin <Sergey.Semin@...kalelectronics.ru>
Subject: Re: [PATCH 4/5] net: stmmac: Add glue layer for Loongson-1 SoC
On Wed, Aug 16, 2023 at 9:30 PM Serge Semin <fancer.lancer@...il.com> wrote:
>
> On Sat, Aug 12, 2023 at 11:11:34PM +0800, Keguang Zhang wrote:
> > This glue driver is created based on the arch-code
> > implemented earlier with the platform-specific settings.
> >
> > Use syscon for SYSCON register access.
> >
> > Partialy based on the previous work by Serge Semin.
> >
> > Signed-off-by: Keguang Zhang <keguang.zhang@...il.com>
> > ---
> > drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
> > drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
> > .../ethernet/stmicro/stmmac/dwmac-loongson1.c | 257 ++++++++++++++++++
> > 3 files changed, 269 insertions(+)
> > create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c
> >
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > index 06c6871f8788..a2b9e289aa36 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > @@ -239,6 +239,17 @@ config DWMAC_INTEL_PLAT
> > the stmmac device driver. This driver is used for the Intel Keem Bay
> > SoC.
> >
> > +config DWMAC_LOONGSON1
> > + tristate "Loongson1 GMAC support"
> > + default MACH_LOONGSON32
> > + depends on OF && (MACH_LOONGSON32 || COMPILE_TEST)
> > + help
> > + Support for ethernet controller on Loongson1 SoC.
> > +
> > + This selects Loongson1 SoC glue layer support for the stmmac
> > + device driver. This driver is used for Loongson1-based boards
> > + like Loongson LS1B/LS1C.
> > +
> > config DWMAC_TEGRA
> > tristate "NVIDIA Tegra MGBE support"
> > depends on ARCH_TEGRA || COMPILE_TEST
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
> > index 5b57aee19267..80e598bd4255 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
> > +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
> > @@ -29,6 +29,7 @@ obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
> > obj-$(CONFIG_DWMAC_SUN8I) += dwmac-sun8i.o
> > obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o
> > obj-$(CONFIG_DWMAC_INTEL_PLAT) += dwmac-intel-plat.o
> > +obj-$(CONFIG_DWMAC_LOONGSON1) += dwmac-loongson1.o
> > obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o
> > obj-$(CONFIG_DWMAC_IMX8) += dwmac-imx.o
> > obj-$(CONFIG_DWMAC_TEGRA) += dwmac-tegra.o
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c
> > new file mode 100644
> > index 000000000000..368d6cd2cb78
> > --- /dev/null
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c
> > @@ -0,0 +1,257 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Loongson-1 DWMAC glue layer
> > + *
> > + * Copyright (C) 2011-2023 Keguang Zhang <keguang.zhang@...il.com>
> > + */
> > +
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/module.h>
> > +#include <linux/phy.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +
> > +#include "stmmac.h"
> > +#include "stmmac_platform.h"
> > +
> > +/* Loongson-1 SYSCON Registers */
> > +#define LS1X_SYSCON0 (0x0)
> > +#define LS1X_SYSCON1 (0x4)
> > +
> > +struct ls1x_dwmac_syscon {
> > + const struct reg_field *reg_fields;
> > + unsigned int nr_reg_fields;
> > + int (*syscon_init)(struct plat_stmmacenet_data *plat);
> > +};
> > +
> > +struct ls1x_dwmac {
> > + struct device *dev;
> > + struct plat_stmmacenet_data *plat_dat;
> > + const struct ls1x_dwmac_syscon *syscon;
> > + struct regmap *regmap;
> > + struct regmap_field *regmap_fields[];
> > +};
> > +
> > +enum ls1b_dwmac_syscon_regfield {
> > + GMAC1_USE_UART1,
> > + GMAC1_USE_UART0,
> > + GMAC1_SHUT,
> > + GMAC0_SHUT,
> > + GMAC1_USE_TXCLK,
> > + GMAC0_USE_TXCLK,
> > + GMAC1_USE_PWM23,
> > + GMAC0_USE_PWM01,
> > +};
> > +
> > +enum ls1c_dwmac_syscon_regfield {
> > + GMAC_SHUT,
> > + PHY_INTF_SELI,
> > +};
> > +
> > +const struct reg_field ls1b_dwmac_syscon_regfields[] = {
> > + [GMAC1_USE_UART1] = REG_FIELD(LS1X_SYSCON0, 4, 4),
> > + [GMAC1_USE_UART0] = REG_FIELD(LS1X_SYSCON0, 3, 3),
> > + [GMAC1_SHUT] = REG_FIELD(LS1X_SYSCON1, 13, 13),
> > + [GMAC0_SHUT] = REG_FIELD(LS1X_SYSCON1, 12, 12),
> > + [GMAC1_USE_TXCLK] = REG_FIELD(LS1X_SYSCON1, 3, 3),
> > + [GMAC0_USE_TXCLK] = REG_FIELD(LS1X_SYSCON1, 2, 2),
> > + [GMAC1_USE_PWM23] = REG_FIELD(LS1X_SYSCON1, 1, 1),
> > + [GMAC0_USE_PWM01] = REG_FIELD(LS1X_SYSCON1, 0, 0)
> > +};
> > +
> > +const struct reg_field ls1c_dwmac_syscon_regfields[] = {
> > + [GMAC_SHUT] = REG_FIELD(LS1X_SYSCON0, 6, 6),
> > + [PHY_INTF_SELI] = REG_FIELD(LS1X_SYSCON1, 28, 30)
> > +};
>
> Emm, using regmap fields looks so over-complicated in this case seeing
> you only need to set/clear several bits in the syscon. What about
> defining macros with the particular flag as it's already done in the
> "asm/mach-loongson32/regs-mux.h" file and using regmap_update_bits()?
>
To use regmap_update_bits(), I have to store and pass reg_offset and
mask, which is similar to the definition of regmap fields.
In addition, the regmap fields are very clear and leave the trouble to
the internal implementation.
> > +
>
> > +static int ls1b_dwmac_syscon_init(struct plat_stmmacenet_data *plat)
> > +{
>
> As I already told you this part is better to be called from the
> plat_stmmacenet_data.fix_mac_speed() because PHY interface mode can
> differ from one interface open cycle to another as per the phylink
> design.
>
I have considered .fix_mac_speed(), which will be called every time
the link is up, and passes the current speed.
However, the PHY interface mode is determined by the hardware design -
the schematic.
In other words, once the schematic is done, the PHY interface mode is fixed.
Therefore, PHY interface mode should be configured one time at the
initialization.
And the plat_stmmacenet_data.init() is the proper place to do this.
> > + struct ls1x_dwmac *dwmac = plat->bsp_priv;
> > + struct regmap_field **regmap_fields = dwmac->regmap_fields;
> > +
>
> > + if (plat->bus_id) {
>
> Using bus_id doesn't look correct to determine the CSRs responsible
> for the interface mode selection because it's calculated based on the
> DT ethernet-alias which doesn't guarantee to have a particular device
> assigned with the alias. Alias node can be absent after all. What
> could be better in this case is for instance to use the regs physical
> address. Any better idea?
>
The purpose of alias is to bind the a particular device with a
particular alias even some aliases are absent.
Because of_alias_get_id() gets the alias id.
For example, LS1B has two GMAC controllers, gmac0 and gmac1.
I have tried the Ethernet with only one alias as follows.
aliases {
ethernet1 = &gmac1;
};
In this case, plat->bus_id is still 1.
And both gmac0 and gmac1 work.
> > + regmap_field_write(regmap_fields[GMAC1_USE_UART1], 1);
> > + regmap_field_write(regmap_fields[GMAC1_USE_UART0], 1);
> > +
> > + switch (plat->phy_interface) {
> > + case PHY_INTERFACE_MODE_RGMII:
> > + regmap_field_write(regmap_fields[GMAC1_USE_TXCLK], 0);
> > + regmap_field_write(regmap_fields[GMAC1_USE_PWM23], 0);
> > + break;
> > + case PHY_INTERFACE_MODE_MII:
> > + regmap_field_write(regmap_fields[GMAC1_USE_TXCLK], 1);
> > + regmap_field_write(regmap_fields[GMAC1_USE_PWM23], 1);
> > + break;
> > + default:
> > + dev_err(dwmac->dev, "Unsupported PHY mode %u\n",
> > + plat->phy_interface);
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + regmap_field_write(regmap_fields[GMAC1_SHUT], 0);
> > + } else {
> > + switch (plat->phy_interface) {
> > + case PHY_INTERFACE_MODE_RGMII:
> > + regmap_field_write(regmap_fields[GMAC0_USE_TXCLK], 0);
> > + regmap_field_write(regmap_fields[GMAC0_USE_PWM01], 0);
> > + break;
> > + case PHY_INTERFACE_MODE_MII:
> > + regmap_field_write(regmap_fields[GMAC0_USE_TXCLK], 1);
> > + regmap_field_write(regmap_fields[GMAC0_USE_PWM01], 1);
> > + break;
> > + default:
> > + dev_err(dwmac->dev, "Unsupported PHY mode %u\n",
> > + plat->phy_interface);
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + regmap_field_write(regmap_fields[GMAC0_SHUT], 0);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ls1c_dwmac_syscon_init(struct plat_stmmacenet_data *plat)
> > +{
> > + struct ls1x_dwmac *dwmac = plat->bsp_priv;
> > + struct regmap_field **regmap_fields = dwmac->regmap_fields;
> > +
> > + if (plat->phy_interface == PHY_INTERFACE_MODE_RMII) {
> > + regmap_field_write(regmap_fields[PHY_INTF_SELI], 0x4);
> > + } else {
> > + dev_err(dwmac->dev, "Unsupported PHY-mode %u\n",
> > + plat->phy_interface);
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + regmap_field_write(regmap_fields[GMAC_SHUT], 0);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct ls1x_dwmac_syscon ls1b_dwmac_syscon = {
> > + .reg_fields = ls1b_dwmac_syscon_regfields,
> > + .nr_reg_fields = ARRAY_SIZE(ls1b_dwmac_syscon_regfields),
> > + .syscon_init = ls1b_dwmac_syscon_init,
> > +};
> > +
> > +static const struct ls1x_dwmac_syscon ls1c_dwmac_syscon = {
> > + .reg_fields = ls1c_dwmac_syscon_regfields,
> > + .nr_reg_fields = ARRAY_SIZE(ls1c_dwmac_syscon_regfields),
> > + .syscon_init = ls1c_dwmac_syscon_init,
> > +};
> > +
> > +static int ls1x_dwmac_init(struct platform_device *pdev, void *priv)
> > +{
> > + struct ls1x_dwmac *dwmac = priv;
> > + int ret;
> > +
>
> > + ret = devm_regmap_field_bulk_alloc(dwmac->dev, dwmac->regmap,
> > + dwmac->regmap_fields,
> > + dwmac->syscon->reg_fields,
> > + dwmac->syscon->nr_reg_fields);
>
> Please see my first comment about this.
>
> > + if (ret)
> > + return ret;
> > +
> > + if (dwmac->syscon->syscon_init) {
> > + ret = dwmac->syscon->syscon_init(dwmac->plat_dat);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id ls1x_dwmac_syscon_match[] = {
> > + { .compatible = "loongson,ls1b-syscon", .data = &ls1b_dwmac_syscon },
> > + { .compatible = "loongson,ls1c-syscon", .data = &ls1c_dwmac_syscon },
> > + { }
> > +};
> > +
> > +static int ls1x_dwmac_probe(struct platform_device *pdev)
> > +{
> > + struct plat_stmmacenet_data *plat_dat;
> > + struct stmmac_resources stmmac_res;
> > + struct device_node *syscon_np;
> > + const struct of_device_id *match;
> > + struct regmap *regmap;
> > + struct ls1x_dwmac *dwmac;
> > + const struct ls1x_dwmac_syscon *syscon;
> > + size_t size;
> > + int ret;
> > +
> > + ret = stmmac_get_platform_resources(pdev, &stmmac_res);
> > + if (ret)
> > + return ret;
> > +
>
> > + /* Probe syscon */
> > + syscon_np = of_parse_phandle(pdev->dev.of_node, "syscon", 0);
>
> it's vendor-specific property so it is supposed to have a
> vendor-specific prefix and possibly ls1-specific name.
>
This has been fixed in v2.
Could you please review v2?
Thanks!
> > + if (!syscon_np)
> > + return -ENODEV;
> > +
> > + match = of_match_node(ls1x_dwmac_syscon_match, syscon_np);
> > + if (!match) {
> > + of_node_put(syscon_np);
> > + return -EINVAL;
> > + }
> > + syscon = (const struct ls1x_dwmac_syscon *)match->data;
> > +
> > + regmap = syscon_node_to_regmap(syscon_np);
> > + of_node_put(syscon_np);
> > + if (IS_ERR(regmap)) {
> > + ret = PTR_ERR(regmap);
> > + dev_err(&pdev->dev, "Unable to map syscon: %d\n", ret);
> > + return ret;
> > + }
>
> or you can use syscon_regmap_lookup_by_phandle(). Using
> of_match_node() doesn't seem necessary since it's unlikely to have
> moee than one system controller available on the LS1b or LS1c chips.
>
I planned to use syscon_regmap_lookup_by_phandle().
Thus the compatible
"loongson,ls1b-dwmac-syscon"/"loongson,ls1c-dwmac-syscon" would become
useless.
I'm not sure about this.
> > +
> > + size = syscon->nr_reg_fields * sizeof(struct regmap_field *);
> > + dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac) + size, GFP_KERNEL);
> > + if (!dwmac)
> > + return -ENOMEM;
> > +
> > + plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac);
> > + if (IS_ERR(plat_dat)) {
> > + dev_err(&pdev->dev, "dt configuration failed\n");
> > + return PTR_ERR(plat_dat);
> > + }
> > +
> > + plat_dat->bsp_priv = dwmac;
> > + plat_dat->init = ls1x_dwmac_init;
> > + dwmac->dev = &pdev->dev;
> > + dwmac->plat_dat = plat_dat;
> > + dwmac->syscon = syscon;
> > + dwmac->regmap = regmap;
> > +
> > + ret = stmmac_pltfr_probe(pdev, plat_dat, &stmmac_res);
> > + if (ret)
> > + goto err_remove_config_dt;
> > +
> > + return 0;
> > +
> > +err_remove_config_dt:
>
> > + if (pdev->dev.of_node)
>
> Is this conditional statement necessary here?
>
You're right.
Will remove this condition in next version.
Thanks!
> -Serge
>
> > + stmmac_remove_config_dt(pdev, plat_dat);
> > +
> > + return ret;
> > +}
> > +
> > +static const struct of_device_id ls1x_dwmac_match[] = {
> > + { .compatible = "loongson,ls1b-dwmac" },
> > + { .compatible = "loongson,ls1c-dwmac" },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, ls1x_dwmac_match);
> > +
> > +static struct platform_driver ls1x_dwmac_driver = {
> > + .probe = ls1x_dwmac_probe,
> > + .remove_new = stmmac_pltfr_remove,
> > + .driver = {
> > + .name = "loongson1-dwmac",
> > + .of_match_table = ls1x_dwmac_match,
> > + },
> > +};
> > +module_platform_driver(ls1x_dwmac_driver);
> > +
> > +MODULE_AUTHOR("Keguang Zhang <keguang.zhang@...il.com>");
> > +MODULE_DESCRIPTION("Loongson1 DWMAC glue layer");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.39.2
> >
--
Best regards,
Keguang Zhang
Powered by blists - more mailing lists