lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <423a3ee3-bed5-02f9-f872-7b5dba64f994@quicinc.com>
Date: Thu, 9 Nov 2023 16:32:36 +0800
From: Jie Luo <quic_luoj@...cinc.com>
To: Maxime Chevallier <maxime.chevallier@...tlin.com>
CC: <andrew@...n.ch>, <hkallweit1@...il.com>, <linux@...linux.org.uk>,
        <davem@...emloft.net>, <edumazet@...gle.com>, <kuba@...nel.org>,
        <pabeni@...hat.com>, <netdev@...r.kernel.org>,
        <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v2 1/3] net: phy: at803x: add QCA8084 ethernet phy support



On 11/8/2023 8:12 PM, Maxime Chevallier wrote:
> Hello,
> 
> On Wed, 8 Nov 2023 19:34:43 +0800
> Luo Jie <quic_luoj@...cinc.com> wrote:
> 
>> Add qca8084 PHY support, which is four-port PHY with maximum
>> link capability 2.5G, the features of each port is almost same
>> as QCA8081 and slave seed config is not needed.
>>
>> Three kind of interface modes supported by qca8084.
>> PHY_INTERFACE_MODE_QUSGMII, PHY_INTERFACE_MODE_2500BASEX and
>> PHY_INTERFACE_MODE_SGMII.
>>
>> The PCS(serdes) and clock are also needed to be configured to
>> bringup qca8084 PHY, which will be added in the pcs driver.
>>
>> The additional CDT configurations used for qca8084.
>>
>> Signed-off-by: Luo Jie <quic_luoj@...cinc.com>
>> ---
>>   drivers/net/phy/at803x.c | 48 ++++++++++++++++++++++++++++++++++++++++
>>   1 file changed, 48 insertions(+)
> 
> [...]
> 
>> @@ -1824,6 +1828,21 @@ static int qca808x_read_status(struct phy_device *phydev)
>>   		return ret;
>>   
>>   	if (phydev->link) {
>> +		/* There are two PCSs available for QCA8084, which support the following
>> +		 * interface modes.
>> +		 *
>> +		 * 1. PHY_INTERFACE_MODE_QUSGMII utilizes PCS1 for all available 4 ports,
>> +		 * which is for all link speeds.
>> +		 *
>> +		 * 2. PHY_INTERFACE_MODE_2500BASEX utilizes PCS0 for the fourth port,
>> +		 * which is only for the link speed 2500M same as QCA8081.
>> +		 *
>> +		 * 3. PHY_INTERFACE_MODE_SGMII utilizes PCS0 for the fourth port,
>> +		 * which is for the link speed 10M, 100M and 1000M same as QCA8081.
>> +		 */
>> +		if (phydev->interface == PHY_INTERFACE_MODE_QUSGMII)
>> +			return 0;
>> +
> 
> What I understand from this is that this PHY can be used either as a
> switch, in which case port 4 would be connected to the host interface
> at up to 2.5G, or as a quad-phy, but since it uses QUSGMII the link
> speed would be limited to 1G per-port, is that correct ?

When the PHY works on the interface mode QUSGMII for quad-phy, all 4
PHYs can support to the max link speed 2.5G, actually the PHY can
support to max link speed 2.5G for all supported interface modes
including qusgmii and sgmii.

> 
> However the get_features function seems to build the supported modes
> set by reading some capabilities registers :
> 
> static int qca808x_get_features(struct phy_device *phydev)
> {
> [...]
> 	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
> 	if (ret < 0)
> 		return ret;
> 
> 	if (QCA808X_PHY_CHIP_TYPE_1G & ret)
> 		linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
> [...]
> }
> 
> Wouldn't port 4 report 2.5G capabilities then ? Maybe you need to
> mask-out the 2.5G bit if the interface is qusgmii.
> 
> Best regards,
> 
> Maxime

All ports including port4 support 2.5G capability for the supported
interface mode.

Thanks Maxime for the review.

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ