| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAJq09z73Q5uu_Nx_kbxSCjc7JwxvoQzLp+=5WX6b2dn6+SH3Ew@mail.gmail.com>
Date: Mon, 11 Dec 2023 02:02:18 -0300
From: Luiz Angelo Daros de Luca <luizluca@...il.com>
To: Alvin Šipraga <ALSI@...g-olufsen.dk>
Cc: "netdev@...r.kernel.org" <netdev@...r.kernel.org>,
"linus.walleij@...aro.org" <linus.walleij@...aro.org>, "andrew@...n.ch" <andrew@...n.ch>,
"f.fainelli@...il.com" <f.fainelli@...il.com>, "olteanv@...il.com" <olteanv@...il.com>,
"davem@...emloft.net" <davem@...emloft.net>, "edumazet@...gle.com" <edumazet@...gle.com>,
"kuba@...nel.org" <kuba@...nel.org>, "pabeni@...hat.com" <pabeni@...hat.com>,
"arinc.unal@...nc9.com" <arinc.unal@...nc9.com>
Subject: Re: [PATCH net-next 4/7] net: dsa: realtek: create realtek-common
> On Fri, Dec 08, 2023 at 01:41:40AM -0300, Luiz Angelo Daros de Luca wrote:
> > Some code can be shared between both interface modules (MDIO and SMI)
> > and among variants. Currently, these interface functions are shared:
> >
> > - realtek_common_lock
> > - realtek_common_unlock
> > - realtek_common_probe
> > - realtek_common_remove
> >
> > The reset during probe was moved to the last moment before a variant
> > detects the switch. This way, we avoid a reset if anything else fails.
> >
> > Signed-off-by: Luiz Angelo Daros de Luca <luizluca@...il.com>
> > Reviewed-by: Linus Walleij <linus.walleij@...aro.org>
> > ---
> > drivers/net/dsa/realtek/Makefile | 1 +
> > drivers/net/dsa/realtek/realtek-common.c | 136 +++++++++++++++++++++++
> > drivers/net/dsa/realtek/realtek-common.h | 16 +++
> > drivers/net/dsa/realtek/realtek-mdio.c | 121 ++------------------
> > drivers/net/dsa/realtek/realtek-smi.c | 124 +++------------------
> > drivers/net/dsa/realtek/realtek.h | 6 +-
> > drivers/net/dsa/realtek/rtl8365mb.c | 9 +-
> > drivers/net/dsa/realtek/rtl8366rb.c | 9 +-
> > 8 files changed, 194 insertions(+), 228 deletions(-)
> > create mode 100644 drivers/net/dsa/realtek/realtek-common.c
> > create mode 100644 drivers/net/dsa/realtek/realtek-common.h
> >
> > diff --git a/drivers/net/dsa/realtek/Makefile b/drivers/net/dsa/realtek/Makefile
> > index 0aab57252a7c..5e0c1ef200a3 100644
> > --- a/drivers/net/dsa/realtek/Makefile
> > +++ b/drivers/net/dsa/realtek/Makefile
> > @@ -1,4 +1,5 @@
> > # SPDX-License-Identifier: GPL-2.0
> > +obj-$(CONFIG_NET_DSA_REALTEK) += realtek-common.o
>
> No corresponding Kconfig change?
NET_DSA_REALTEK already existed for "Realtek Ethernet switch family
support" entry to the Realtek DSA switch submenu. In the way we used
to use it, I believe it should be a bool entry, not a tristate. Now,
with a common module, a tristate fits just fine. So, by mistake, no
change is needed.
> > obj-$(CONFIG_NET_DSA_REALTEK_MDIO) += realtek-mdio.o
> > obj-$(CONFIG_NET_DSA_REALTEK_SMI) += realtek-smi.o
> > obj-$(CONFIG_NET_DSA_REALTEK_RTL8366RB) += rtl8366.o
> > diff --git a/drivers/net/dsa/realtek/realtek-common.c b/drivers/net/dsa/realtek/realtek-common.c
> > new file mode 100644
> > index 000000000000..75b6aa071990
> > --- /dev/null
> > +++ b/drivers/net/dsa/realtek/realtek-common.c
> > @@ -0,0 +1,136 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +
> > +#include <linux/module.h>
> > +
> > +#include "realtek.h"
> > +#include "realtek-common.h"
> > +
> > +void realtek_common_lock(void *ctx)
> > +{
> > + struct realtek_priv *priv = ctx;
> > +
> > + mutex_lock(&priv->map_lock);
> > +}
> > +EXPORT_SYMBOL_GPL(realtek_common_lock);
> > +
> > +void realtek_common_unlock(void *ctx)
> > +{
> > + struct realtek_priv *priv = ctx;
> > +
> > + mutex_unlock(&priv->map_lock);
> > +}
> > +EXPORT_SYMBOL_GPL(realtek_common_unlock);
> > +
> > +struct realtek_priv *
> > +realtek_common_probe_pre(struct device *dev, struct regmap_config rc,
> > + struct regmap_config rc_nolock)
> > +{
> > + const struct realtek_variant *var;
> > + struct realtek_priv *priv;
> > + struct device_node *np;
> > + int ret;
> > +
> > + var = of_device_get_match_data(dev);
> > + if (!var)
> > + return ERR_PTR(-EINVAL);
> > +
> > + priv = devm_kzalloc(dev, size_add(sizeof(*priv), var->chip_data_sz),
> > + GFP_KERNEL);
> > + if (!priv)
> > + return ERR_PTR(-ENOMEM);
> > +
> > + mutex_init(&priv->map_lock);
> > +
> > + rc.lock_arg = priv;
> > + priv->map = devm_regmap_init(dev, NULL, priv, &rc);
> > + if (IS_ERR(priv->map)) {
> > + ret = PTR_ERR(priv->map);
> > + dev_err(dev, "regmap init failed: %d\n", ret);
> > + return ERR_PTR(ret);
> > + }
> > +
> > + priv->map_nolock = devm_regmap_init(dev, NULL, priv, &rc_nolock);
> > + if (IS_ERR(priv->map_nolock)) {
> > + ret = PTR_ERR(priv->map_nolock);
> > + dev_err(dev, "regmap init failed: %d\n", ret);
> > + return ERR_PTR(ret);
> > + }
> > +
> > + /* Link forward and backward */
> > + priv->dev = dev;
> > + priv->variant = var;
> > + priv->ops = var->ops;
> > + priv->chip_data = (void *)priv + sizeof(*priv);
> > +
> > + dev_set_drvdata(dev, priv);
> > + spin_lock_init(&priv->lock);
> > +
> > + np = dev->of_node;
>
> This is kind of a pointless variable, just do
> of_property_read_bool(dev->of_node, ...) below.
OK.
>
> > +
> > + priv->leds_disabled = of_property_read_bool(np, "realtek,disable-leds");
> > +
> > + /* TODO: if power is software controlled, set up any regulators here */
> > +
> > + priv->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> > + if (IS_ERR(priv->reset)) {
> > + dev_err(dev, "failed to get RESET GPIO\n");
> > + return ERR_CAST(priv->reset);
> > + }
> > + if (priv->reset) {
> > + gpiod_set_value(priv->reset, 1);
> > + dev_dbg(dev, "asserted RESET\n");
> > + msleep(REALTEK_HW_STOP_DELAY);
> > + gpiod_set_value(priv->reset, 0);
> > + msleep(REALTEK_HW_START_DELAY);
> > + dev_dbg(dev, "deasserted RESET\n");
> > + }
> > +
> > + return priv;
> > +}
> > +EXPORT_SYMBOL(realtek_common_probe_pre);
> > +
> > +int realtek_common_probe_post(struct realtek_priv *priv)
> > +{
> > + int ret;
> > +
> > + ret = priv->ops->detect(priv);
> > + if (ret) {
> > + dev_err(priv->dev, "unable to detect switch\n");
>
> dev_err_probe()?
I'm not sure if detect() is able to return -EPROBE. At least for SMI,
gpio read/write never returns errors. However, it will not hurt to use
dev_err_probe() here.
>
> > + return ret;
> > + }
> > +
> > + priv->ds = devm_kzalloc(priv->dev, sizeof(*priv->ds), GFP_KERNEL);
> > + if (!priv->ds)
> > + return -ENOMEM;
>
> I guess this could actually just be embedded in realtek_priv and then
> you don't need to allocate it dynamically here.
It makes sense. However, shouldn't it be a different commit? This one
is just moving stuff to a common file, not trying to optimize de code.
> > +
> > + priv->ds->priv = priv;
> > + priv->ds->dev = priv->dev;
> > + priv->ds->ops = priv->ds_ops;
> > + priv->ds->num_ports = priv->num_ports;
> > +
> > + ret = dsa_register_switch(priv->ds);
> > + if (ret) {
> > + dev_err_probe(priv->dev, ret, "unable to register switch\n");
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +EXPORT_SYMBOL(realtek_common_probe_post);
> > +
> > +void realtek_common_remove(struct realtek_priv *priv)
> > +{
> > + if (!priv)
> > + return;
> > +
> > + dsa_unregister_switch(priv->ds);
> > +
> > + /* leave the device reset asserted */
> > + if (priv->reset)
> > + gpiod_set_value(priv->reset, 1);
> > +}
> > +EXPORT_SYMBOL(realtek_common_remove);
> > +
> > +MODULE_AUTHOR("Luiz Angelo Daros de Luca <luizluca@...il.com>");
> > +MODULE_DESCRIPTION("Realtek DSA switches common module");
> > +MODULE_LICENSE("GPL");
> > diff --git a/drivers/net/dsa/realtek/realtek-common.h b/drivers/net/dsa/realtek/realtek-common.h
> > new file mode 100644
> > index 000000000000..405bd0d85d2b
> > --- /dev/null
> > +++ b/drivers/net/dsa/realtek/realtek-common.h
> > @@ -0,0 +1,16 @@
> > +/* SPDX-License-Identifier: GPL-2.0+ */
> > +
> > +#ifndef _REALTEK_INTERFACE_H
> > +#define _REALTEK_INTERFACE_H
> > +
> > +#include <linux/regmap.h>
> > +
> > +void realtek_common_lock(void *ctx);
> > +void realtek_common_unlock(void *ctx);
> > +struct realtek_priv *
> > +realtek_common_probe_pre(struct device *dev, struct regmap_config rc,
> > + struct regmap_config rc_nolock);
> > +int realtek_common_probe_post(struct realtek_priv *priv);
>
> Maybe it is worth describing what these functions do with a comment.
>
> pre: sets up driver private data struct, sets up regmaps, issues
> hardware reset
>
> post: registers the dsa switch, calls detect() and then expects
> priv->num_ports to be set
Sure. I'm not sure about the "expects". If I need something, I should
check and fail. The DSA switch will already fail to register without a
non-zero number of ports. (although too silently for my taste).
I don't like names that need too much explanation. It is just a
symptom of a bad name. Would it make more sense to have
realtek_common_probe_pre -> realtek_common_probe
realtek_common_probe_post -> realtek_common_register_switch (although
it is also detecting the switch)
?
> The detect() function in itself is a bit funny. Maybe it's not even
> necessary. Both chip variants set a static num_ports value anyway. You
> can maybe dump detect() completely and move that code into the
> variant-specific probe between the calls to common_probe_{pre,post}().
The probe is not variant-specific but interface-specific. We could,
indeed, put a static num_ports into realtek_variant and use it.
However, the main use for detect is to validate you really got a
supported switch, with the setups being a secondary function. I would
leave it as is for now. I'm trying to keep the series as small as
possible.
> > +void realtek_common_remove(struct realtek_priv *priv);
> > +
> > +#endif
>
> #endif /* _REALTEK_INTERFACE_H */
>
> Actually shouldn't it be _REALTEK_COMMON_H?
Yes, bad ctrl+c/ctrl+v from Vladmir example code.
> > diff --git a/drivers/net/dsa/realtek/realtek-mdio.c b/drivers/net/dsa/realtek/realtek-mdio.c
> > index 58966d0625c8..4c9a744b72f8 100644
> > --- a/drivers/net/dsa/realtek/realtek-mdio.c
> > +++ b/drivers/net/dsa/realtek/realtek-mdio.c
> > @@ -26,6 +26,7 @@
> >
> > #include "realtek.h"
> > #include "realtek-mdio.h"
> > +#include "realtek-common.h"
> >
> > /* Read/write via mdiobus */
> > #define REALTEK_MDIO_CTRL0_REG 31
> > @@ -100,20 +101,6 @@ static int realtek_mdio_read(void *ctx, u32 reg, u32 *val)
> > return ret;
> > }
> >
> > -static void realtek_mdio_lock(void *ctx)
> > -{
> > - struct realtek_priv *priv = ctx;
> > -
> > - mutex_lock(&priv->map_lock);
> > -}
> > -
> > -static void realtek_mdio_unlock(void *ctx)
> > -{
> > - struct realtek_priv *priv = ctx;
> > -
> > - mutex_unlock(&priv->map_lock);
> > -}
> > -
> > static const struct regmap_config realtek_mdio_regmap_config = {
> > .reg_bits = 10, /* A4..A0 R4..R0 */
> > .val_bits = 16,
> > @@ -124,8 +111,8 @@ static const struct regmap_config realtek_mdio_regmap_config = {
> > .reg_read = realtek_mdio_read,
> > .reg_write = realtek_mdio_write,
> > .cache_type = REGCACHE_NONE,
> > - .lock = realtek_mdio_lock,
> > - .unlock = realtek_mdio_unlock,
> > + .lock = realtek_common_lock,
> > + .unlock = realtek_common_unlock,
> > };
> >
> > static const struct regmap_config realtek_mdio_nolock_regmap_config = {
> > @@ -143,98 +130,21 @@ static const struct regmap_config realtek_mdio_nolock_regmap_config = {
> >
> > int realtek_mdio_probe(struct mdio_device *mdiodev)
> > {
> > - struct realtek_priv *priv;
> > struct device *dev = &mdiodev->dev;
> > - const struct realtek_variant *var;
> > - struct regmap_config rc;
> > - struct device_node *np;
> > - int ret;
> > -
> > - var = of_device_get_match_data(dev);
> > - if (!var)
> > - return -EINVAL;
> > -
> > - priv = devm_kzalloc(&mdiodev->dev,
> > - size_add(sizeof(*priv), var->chip_data_sz),
> > - GFP_KERNEL);
> > - if (!priv)
> > - return -ENOMEM;
> > -
> > - mutex_init(&priv->map_lock);
> > -
> > - rc = realtek_mdio_regmap_config;
> > - rc.lock_arg = priv;
> > - priv->map = devm_regmap_init(dev, NULL, priv, &rc);
> > - if (IS_ERR(priv->map)) {
> > - ret = PTR_ERR(priv->map);
> > - dev_err(dev, "regmap init failed: %d\n", ret);
> > - return ret;
> > - }
> > + struct realtek_priv *priv;
> >
> > - rc = realtek_mdio_nolock_regmap_config;
> > - priv->map_nolock = devm_regmap_init(dev, NULL, priv, &rc);
> > - if (IS_ERR(priv->map_nolock)) {
> > - ret = PTR_ERR(priv->map_nolock);
> > - dev_err(dev, "regmap init failed: %d\n", ret);
> > - return ret;
> > - }
> > + priv = realtek_common_probe_pre(dev, realtek_mdio_regmap_config,
> > + realtek_mdio_nolock_regmap_config);
> > + if (IS_ERR(priv))
> > + return PTR_ERR(priv);
> >
> > - priv->mdio_addr = mdiodev->addr;
> > priv->bus = mdiodev->bus;
> > - priv->dev = &mdiodev->dev;
> > - priv->chip_data = (void *)priv + sizeof(*priv);
> > -
> > - priv->clk_delay = var->clk_delay;
> > - priv->cmd_read = var->cmd_read;
> > - priv->cmd_write = var->cmd_write;
> > - priv->ops = var->ops;
> > -
> > + priv->mdio_addr = mdiodev->addr;
> > priv->write_reg_noack = realtek_mdio_write;
> > + priv->ds_ops = priv->variant->ds_ops_mdio;
> >
> > - np = dev->of_node;
> > -
> > - dev_set_drvdata(dev, priv);
> > -
> > - /* TODO: if power is software controlled, set up any regulators here */
> > - priv->leds_disabled = of_property_read_bool(np, "realtek,disable-leds");
> > -
> > - priv->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> > - if (IS_ERR(priv->reset)) {
> > - dev_err(dev, "failed to get RESET GPIO\n");
> > - return PTR_ERR(priv->reset);
> > - }
> > -
> > - if (priv->reset) {
> > - gpiod_set_value(priv->reset, 1);
> > - dev_dbg(dev, "asserted RESET\n");
> > - msleep(REALTEK_HW_STOP_DELAY);
> > - gpiod_set_value(priv->reset, 0);
> > - msleep(REALTEK_HW_START_DELAY);
> > - dev_dbg(dev, "deasserted RESET\n");
> > - }
> > -
> > - ret = priv->ops->detect(priv);
> > - if (ret) {
> > - dev_err(dev, "unable to detect switch\n");
> > - return ret;
> > - }
> > -
> > - priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL);
> > - if (!priv->ds)
> > - return -ENOMEM;
> > -
> > - priv->ds->dev = dev;
> > - priv->ds->num_ports = priv->num_ports;
> > - priv->ds->priv = priv;
> > - priv->ds->ops = var->ds_ops_mdio;
> > -
> > - ret = dsa_register_switch(priv->ds);
> > - if (ret) {
> > - dev_err(priv->dev, "unable to register switch ret = %d\n", ret);
> > - return ret;
> > - }
> > + return realtek_common_probe_post(priv);
> >
> > - return 0;
> > }
> > EXPORT_SYMBOL_GPL(realtek_mdio_probe);
> >
> > @@ -242,14 +152,7 @@ void realtek_mdio_remove(struct mdio_device *mdiodev)
> > {
> > struct realtek_priv *priv = dev_get_drvdata(&mdiodev->dev);
> >
> > - if (!priv)
> > - return;
> > -
> > - dsa_unregister_switch(priv->ds);
> > -
> > - /* leave the device reset asserted */
> > - if (priv->reset)
> > - gpiod_set_value(priv->reset, 1);
> > + realtek_common_remove(priv);
> > }
> > EXPORT_SYMBOL_GPL(realtek_mdio_remove);
> >
> > diff --git a/drivers/net/dsa/realtek/realtek-smi.c b/drivers/net/dsa/realtek/realtek-smi.c
> > index 55586d158c0e..246024eec3bd 100644
> > --- a/drivers/net/dsa/realtek/realtek-smi.c
> > +++ b/drivers/net/dsa/realtek/realtek-smi.c
> > @@ -41,12 +41,13 @@
> >
> > #include "realtek.h"
> > #include "realtek-smi.h"
> > +#include "realtek-common.h"
> >
> > #define REALTEK_SMI_ACK_RETRY_COUNT 5
> >
> > static inline void realtek_smi_clk_delay(struct realtek_priv *priv)
> > {
> > - ndelay(priv->clk_delay);
> > + ndelay(priv->variant->clk_delay);
> > }
> >
> > static void realtek_smi_start(struct realtek_priv *priv)
> > @@ -209,7 +210,7 @@ static int realtek_smi_read_reg(struct realtek_priv *priv, u32 addr, u32 *data)
> > realtek_smi_start(priv);
> >
> > /* Send READ command */
> > - ret = realtek_smi_write_byte(priv, priv->cmd_read);
> > + ret = realtek_smi_write_byte(priv, priv->variant->cmd_read);
> > if (ret)
> > goto out;
> >
> > @@ -250,7 +251,7 @@ static int realtek_smi_write_reg(struct realtek_priv *priv,
> > realtek_smi_start(priv);
> >
> > /* Send WRITE command */
> > - ret = realtek_smi_write_byte(priv, priv->cmd_write);
> > + ret = realtek_smi_write_byte(priv, priv->variant->cmd_write);
> > if (ret)
> > goto out;
> >
> > @@ -311,20 +312,6 @@ static int realtek_smi_read(void *ctx, u32 reg, u32 *val)
> > return realtek_smi_read_reg(priv, reg, val);
> > }
> >
> > -static void realtek_smi_lock(void *ctx)
> > -{
> > - struct realtek_priv *priv = ctx;
> > -
> > - mutex_lock(&priv->map_lock);
> > -}
> > -
> > -static void realtek_smi_unlock(void *ctx)
> > -{
> > - struct realtek_priv *priv = ctx;
> > -
> > - mutex_unlock(&priv->map_lock);
> > -}
> > -
> > static const struct regmap_config realtek_smi_regmap_config = {
> > .reg_bits = 10, /* A4..A0 R4..R0 */
> > .val_bits = 16,
> > @@ -335,8 +322,8 @@ static const struct regmap_config realtek_smi_regmap_config = {
> > .reg_read = realtek_smi_read,
> > .reg_write = realtek_smi_write,
> > .cache_type = REGCACHE_NONE,
> > - .lock = realtek_smi_lock,
> > - .unlock = realtek_smi_unlock,
> > + .lock = realtek_common_lock,
> > + .unlock = realtek_common_unlock,
> > };
> >
> > static const struct regmap_config realtek_smi_nolock_regmap_config = {
> > @@ -411,100 +398,28 @@ static int realtek_smi_setup_mdio(struct dsa_switch *ds)
> >
> > int realtek_smi_probe(struct platform_device *pdev)
> > {
> > - const struct realtek_variant *var;
> > struct device *dev = &pdev->dev;
> > struct realtek_priv *priv;
> > - struct regmap_config rc;
> > - struct device_node *np;
> > - int ret;
> > -
> > - var = of_device_get_match_data(dev);
> > - np = dev->of_node;
> > -
> > - priv = devm_kzalloc(dev, sizeof(*priv) + var->chip_data_sz, GFP_KERNEL);
> > - if (!priv)
> > - return -ENOMEM;
> > - priv->chip_data = (void *)priv + sizeof(*priv);
> > -
> > - mutex_init(&priv->map_lock);
> > -
> > - rc = realtek_smi_regmap_config;
> > - rc.lock_arg = priv;
> > - priv->map = devm_regmap_init(dev, NULL, priv, &rc);
> > - if (IS_ERR(priv->map)) {
> > - ret = PTR_ERR(priv->map);
> > - dev_err(dev, "regmap init failed: %d\n", ret);
> > - return ret;
> > - }
> > -
> > - rc = realtek_smi_nolock_regmap_config;
> > - priv->map_nolock = devm_regmap_init(dev, NULL, priv, &rc);
> > - if (IS_ERR(priv->map_nolock)) {
> > - ret = PTR_ERR(priv->map_nolock);
> > - dev_err(dev, "regmap init failed: %d\n", ret);
> > - return ret;
> > - }
> > -
> > - /* Link forward and backward */
> > - priv->dev = dev;
> > - priv->clk_delay = var->clk_delay;
> > - priv->cmd_read = var->cmd_read;
> > - priv->cmd_write = var->cmd_write;
> > - priv->ops = var->ops;
> > -
> > - priv->setup_interface = realtek_smi_setup_mdio;
> > - priv->write_reg_noack = realtek_smi_write_reg_noack;
> > -
> > - dev_set_drvdata(dev, priv);
> > - spin_lock_init(&priv->lock);
> >
> > - /* TODO: if power is software controlled, set up any regulators here */
> > -
> > - priv->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> > - if (IS_ERR(priv->reset)) {
> > - dev_err(dev, "failed to get RESET GPIO\n");
> > - return PTR_ERR(priv->reset);
> > - }
> > - if (priv->reset) {
> > - gpiod_set_value(priv->reset, 1);
> > - dev_dbg(dev, "asserted RESET\n");
> > - msleep(REALTEK_HW_STOP_DELAY);
> > - gpiod_set_value(priv->reset, 0);
> > - msleep(REALTEK_HW_START_DELAY);
> > - dev_dbg(dev, "deasserted RESET\n");
> > - }
> > + priv = realtek_common_probe_pre(dev, realtek_smi_regmap_config,
> > + realtek_smi_nolock_regmap_config);
> > + if (IS_ERR(priv))
> > + return PTR_ERR(priv);
> >
> > /* Fetch MDIO pins */
> > priv->mdc = devm_gpiod_get_optional(dev, "mdc", GPIOD_OUT_LOW);
> > if (IS_ERR(priv->mdc))
> > return PTR_ERR(priv->mdc);
> > +
> > priv->mdio = devm_gpiod_get_optional(dev, "mdio", GPIOD_OUT_LOW);
> > if (IS_ERR(priv->mdio))
> > return PTR_ERR(priv->mdio);
> >
> > - priv->leds_disabled = of_property_read_bool(np, "realtek,disable-leds");
> > -
> > - ret = priv->ops->detect(priv);
> > - if (ret) {
> > - dev_err(dev, "unable to detect switch\n");
> > - return ret;
> > - }
> > -
> > - priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL);
> > - if (!priv->ds)
> > - return -ENOMEM;
> > -
> > - priv->ds->dev = dev;
> > - priv->ds->num_ports = priv->num_ports;
> > - priv->ds->priv = priv;
> > + priv->write_reg_noack = realtek_smi_write_reg_noack;
> > + priv->setup_interface = realtek_smi_setup_mdio;
> > + priv->ds_ops = priv->variant->ds_ops_smi;
> >
> > - priv->ds->ops = var->ds_ops_smi;
> > - ret = dsa_register_switch(priv->ds);
> > - if (ret) {
> > - dev_err_probe(dev, ret, "unable to register switch\n");
> > - return ret;
> > - }
> > - return 0;
> > + return (priv);
>
> ret = realtek_common_probe_post(priv);
> if (ret)
> return ret;
>
> return 0;
The ret variable is no more. Is it worth it to replace a single line
with 4 more?
> > }
> > EXPORT_SYMBOL_GPL(realtek_smi_probe);
> >
> > @@ -512,14 +427,7 @@ void realtek_smi_remove(struct platform_device *pdev)
> > {
> > struct realtek_priv *priv = platform_get_drvdata(pdev);
> >
> > - if (!priv)
> > - return;
> > -
> > - dsa_unregister_switch(priv->ds);
> > -
> > - /* leave the device reset asserted */
> > - if (priv->reset)
> > - gpiod_set_value(priv->reset, 1);
> > + realtek_common_remove(priv);
> > }
> > EXPORT_SYMBOL_GPL(realtek_smi_remove);
> >
> > diff --git a/drivers/net/dsa/realtek/realtek.h b/drivers/net/dsa/realtek/realtek.h
> > index e9ee778665b2..fbd0616c1df3 100644
> > --- a/drivers/net/dsa/realtek/realtek.h
> > +++ b/drivers/net/dsa/realtek/realtek.h
> > @@ -58,11 +58,9 @@ struct realtek_priv {
> > struct mii_bus *bus;
> > int mdio_addr;
> >
> > - unsigned int clk_delay;
> > - u8 cmd_read;
> > - u8 cmd_write;
> > spinlock_t lock; /* Locks around command writes */
> > struct dsa_switch *ds;
> > + const struct dsa_switch_ops *ds_ops;
> > struct irq_domain *irqdomain;
> > bool leds_disabled;
> >
> > @@ -79,6 +77,8 @@ struct realtek_priv {
> > int vlan_enabled;
> > int vlan4k_enabled;
> >
> > + const struct realtek_variant *variant;
> > +
> > char buf[4096];
> > void *chip_data; /* Per-chip extra variant data */
> > };
> > diff --git a/drivers/net/dsa/realtek/rtl8365mb.c b/drivers/net/dsa/realtek/rtl8365mb.c
> > index 526bf98cef1d..ac848b965f84 100644
> > --- a/drivers/net/dsa/realtek/rtl8365mb.c
> > +++ b/drivers/net/dsa/realtek/rtl8365mb.c
> > @@ -103,6 +103,7 @@
> > #include "realtek.h"
> > #include "realtek-smi.h"
> > #include "realtek-mdio.h"
> > +#include "realtek-common.h"
> >
> > /* Family-specific data and limits */
> > #define RTL8365MB_PHYADDRMAX 7
> > @@ -691,7 +692,7 @@ static int rtl8365mb_phy_ocp_read(struct realtek_priv *priv, int phy,
> > u32 val;
> > int ret;
> >
> > - mutex_lock(&priv->map_lock);
> > + realtek_common_lock(priv);
> >
> > ret = rtl8365mb_phy_poll_busy(priv);
> > if (ret)
> > @@ -724,7 +725,7 @@ static int rtl8365mb_phy_ocp_read(struct realtek_priv *priv, int phy,
> > *data = val & 0xFFFF;
> >
> > out:
> > - mutex_unlock(&priv->map_lock);
> > + realtek_common_unlock(priv);
> >
> > return ret;
> > }
> > @@ -735,7 +736,7 @@ static int rtl8365mb_phy_ocp_write(struct realtek_priv *priv, int phy,
> > u32 val;
> > int ret;
> >
> > - mutex_lock(&priv->map_lock);
> > + realtek_common_lock(priv);
> >
> > ret = rtl8365mb_phy_poll_busy(priv);
> > if (ret)
> > @@ -766,7 +767,7 @@ static int rtl8365mb_phy_ocp_write(struct realtek_priv *priv, int phy,
> > goto out;
> >
> > out:
> > - mutex_unlock(&priv->map_lock);
> > + realtek_common_unlock(priv);
> >
> > return 0;
> > }
> > diff --git a/drivers/net/dsa/realtek/rtl8366rb.c b/drivers/net/dsa/realtek/rtl8366rb.c
> > index 09c17de19457..1cc4de3cf54f 100644
> > --- a/drivers/net/dsa/realtek/rtl8366rb.c
> > +++ b/drivers/net/dsa/realtek/rtl8366rb.c
> > @@ -24,6 +24,7 @@
> > #include "realtek.h"
> > #include "realtek-smi.h"
> > #include "realtek-mdio.h"
> > +#include "realtek-common.h"
> >
> > #define RTL8366RB_PORT_NUM_CPU 5
> > #define RTL8366RB_NUM_PORTS 6
> > @@ -1707,7 +1708,7 @@ static int rtl8366rb_phy_read(struct realtek_priv *priv, int phy, int regnum)
> > if (phy > RTL8366RB_PHY_NO_MAX)
> > return -EINVAL;
> >
> > - mutex_lock(&priv->map_lock);
> > + realtek_common_lock(priv);
> >
> > ret = regmap_write(priv->map_nolock, RTL8366RB_PHY_ACCESS_CTRL_REG,
> > RTL8366RB_PHY_CTRL_READ);
> > @@ -1735,7 +1736,7 @@ static int rtl8366rb_phy_read(struct realtek_priv *priv, int phy, int regnum)
> > phy, regnum, reg, val);
> >
> > out:
> > - mutex_unlock(&priv->map_lock);
> > + realtek_common_unlock(priv);
> >
> > return ret;
> > }
> > @@ -1749,7 +1750,7 @@ static int rtl8366rb_phy_write(struct realtek_priv *priv, int phy, int regnum,
> > if (phy > RTL8366RB_PHY_NO_MAX)
> > return -EINVAL;
> >
> > - mutex_lock(&priv->map_lock);
> > + realtek_common_lock(priv);
> >
> > ret = regmap_write(priv->map_nolock, RTL8366RB_PHY_ACCESS_CTRL_REG,
> > RTL8366RB_PHY_CTRL_WRITE);
> > @@ -1766,7 +1767,7 @@ static int rtl8366rb_phy_write(struct realtek_priv *priv, int phy, int regnum,
> > goto out;
> >
> > out:
> > - mutex_unlock(&priv->map_lock);
> > + realtek_common_unlock(priv);
> >
> > return ret;
> > }
> > --
> > 2.43.0
> >
Regards,
Luiz
Powered by blists - more mailing lists