| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20231214114600.2451162-22-claudiu.beznea.uj@bp.renesas.com>
Date: Thu, 14 Dec 2023 13:46:00 +0200
From: Claudiu <claudiu.beznea@...on.dev>
To: s.shtylyov@....ru,
davem@...emloft.net,
edumazet@...gle.com,
kuba@...nel.org,
pabeni@...hat.com,
richardcochran@...il.com,
p.zabel@...gutronix.de,
yoshihiro.shimoda.uh@...esas.com,
wsa+renesas@...g-engineering.com,
geert+renesas@...der.be
Cc: netdev@...r.kernel.org,
linux-renesas-soc@...r.kernel.org,
linux-kernel@...r.kernel.org,
Claudiu Beznea <claudiu.beznea.uj@...renesas.com>
Subject: [PATCH net-next v2 21/21] net: ravb: Add runtime PM support
From: Claudiu Beznea <claudiu.beznea.uj@...renesas.com>
Add runtime PM support for the ravb driver. As the driver is used by
different IP variants, with different behaviors, to be able to have the
runtime PM support available for all devices, the preparatory commits
moved all the resources parsing and allocations in the driver's probe
function and kept the settings for ravb_open(). This is due to the fact
that on some IP variants-platforms tuples disabling/enabling the clocks
will switch the IP to the reset operation mode where registers' content is
lost and reconfiguration needs to be done. For this the rabv_open()
function enables the clocks, switches the IP to configuration mode, applies
all the registers settings and switches the IP to the operational mode. At
the end of ravb_open() IP is ready to send/receive data.
In ravb_close() necessary reverts are done (compared with ravb_open()), the
IP is switched to reset mode and clocks are disabled.
The ethtool APIs or IOCTLs that might execute while the interface is down
are either cached (and applied in ravb_open()) or rejected (as at that time
the IP is in reset mode). Keeping the IP in the reset mode also increases
the power saved (according to the hardware manual).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@...renesas.com>
---
Changes in v2:
- keep RPM support for all platforms
drivers/net/ethernet/renesas/ravb_main.c | 47 ++++++++++++++++++++++--
1 file changed, 44 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c
index 9ff943dff522..0733b63ff910 100644
--- a/drivers/net/ethernet/renesas/ravb_main.c
+++ b/drivers/net/ethernet/renesas/ravb_main.c
@@ -1839,16 +1839,21 @@ static int ravb_open(struct net_device *ndev)
{
struct ravb_private *priv = netdev_priv(ndev);
const struct ravb_hw_info *info = priv->info;
+ struct device *dev = &priv->pdev->dev;
int error;
napi_enable(&priv->napi[RAVB_BE]);
if (info->nc_queues)
napi_enable(&priv->napi[RAVB_NC]);
+ error = pm_runtime_resume_and_get(dev);
+ if (error < 0)
+ goto out_napi_off;
+
/* Set AVB config mode */
error = ravb_set_config_mode(ndev);
if (error)
- goto out_napi_off;
+ goto out_rpm_put;
ravb_set_delay_mode(ndev);
ravb_write(ndev, priv->desc_bat_dma, DBAT);
@@ -1894,6 +1899,9 @@ static int ravb_open(struct net_device *ndev)
ravb_stop_dma(ndev);
out_set_reset:
ravb_set_reset_mode(ndev);
+out_rpm_put:
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
out_napi_off:
if (info->nc_queues)
napi_disable(&priv->napi[RAVB_NC]);
@@ -2189,6 +2197,7 @@ static int ravb_close(struct net_device *ndev)
struct ravb_private *priv = netdev_priv(ndev);
const struct ravb_hw_info *info = priv->info;
struct ravb_tstamp_skb *ts_skb, *ts_skb2;
+ struct device *dev = &priv->pdev->dev;
netif_tx_stop_all_queues(ndev);
@@ -2237,6 +2246,9 @@ static int ravb_close(struct net_device *ndev)
/* Set reset mode. */
ravb_set_reset_mode(ndev);
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
+
return 0;
}
@@ -2808,6 +2820,8 @@ static int ravb_probe(struct platform_device *pdev)
clk_prepare(priv->refclk);
platform_set_drvdata(pdev, ndev);
+ pm_runtime_set_autosuspend_delay(&pdev->dev, 100);
+ pm_runtime_use_autosuspend(&pdev->dev);
pm_runtime_enable(&pdev->dev);
error = pm_runtime_resume_and_get(&pdev->dev);
if (error < 0)
@@ -2916,6 +2930,9 @@ static int ravb_probe(struct platform_device *pdev)
netdev_info(ndev, "Base address at %#x, %pM, IRQ %d.\n",
(u32)ndev->base_addr, ndev->dev_addr, ndev->irq);
+ pm_runtime_mark_last_busy(&pdev->dev);
+ pm_runtime_put_autosuspend(&pdev->dev);
+
return 0;
out_netdev_unregister:
@@ -2934,6 +2951,7 @@ static int ravb_probe(struct platform_device *pdev)
pm_runtime_put(&pdev->dev);
out_rpm_disable:
pm_runtime_disable(&pdev->dev);
+ pm_runtime_dont_use_autosuspend(&pdev->dev);
clk_unprepare(priv->refclk);
out_reset_assert:
reset_control_assert(rstc);
@@ -2947,6 +2965,12 @@ static void ravb_remove(struct platform_device *pdev)
struct net_device *ndev = platform_get_drvdata(pdev);
struct ravb_private *priv = netdev_priv(ndev);
const struct ravb_hw_info *info = priv->info;
+ struct device *dev = &priv->pdev->dev;
+ int error;
+
+ error = pm_runtime_resume_and_get(dev);
+ if (error < 0)
+ return;
unregister_netdev(ndev);
if (info->nc_queues)
@@ -2958,8 +2982,9 @@ static void ravb_remove(struct platform_device *pdev)
dma_free_coherent(ndev->dev.parent, priv->desc_bat_size, priv->desc_bat,
priv->desc_bat_dma);
- pm_runtime_put_sync(&pdev->dev);
+ pm_runtime_put_sync_suspend(&pdev->dev);
pm_runtime_disable(&pdev->dev);
+ pm_runtime_dont_use_autosuspend(dev);
clk_unprepare(priv->refclk);
reset_control_assert(priv->rstc);
free_netdev(ndev);
@@ -3041,6 +3066,10 @@ static int ravb_suspend(struct device *dev)
if (ret)
return ret;
+ ret = pm_runtime_force_suspend(&priv->pdev->dev);
+ if (ret)
+ return ret;
+
reset_assert:
return reset_control_assert(priv->rstc);
}
@@ -3063,16 +3092,28 @@ static int ravb_resume(struct device *dev)
ret = ravb_wol_restore(ndev);
if (ret)
return ret;
+ } else {
+ ret = pm_runtime_force_resume(dev);
+ if (ret)
+ return ret;
}
/* Reopening the interface will restore the device to the working state. */
ret = ravb_open(ndev);
if (ret < 0)
- return ret;
+ goto out_rpm_put;
ravb_set_rx_mode(ndev);
netif_device_attach(ndev);
+ return 0;
+
+out_rpm_put:
+ if (!priv->wol_enabled) {
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
+ }
+
return ret;
}
--
2.39.2
Powered by blists - more mailing lists