| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <m7aqhrk5zydicvxdrl225tcgwe5g3esu27mafoee7pqjitjnzs@5ldkbzqmmpte>
Date: Wed, 20 Dec 2023 10:40:25 +0000
From: Alvin Šipraga <ALSI@...g-olufsen.dk>
To: Luiz Angelo Daros de Luca <luizluca@...il.com>
CC: "netdev@...r.kernel.org" <netdev@...r.kernel.org>,
"linus.walleij@...aro.org" <linus.walleij@...aro.org>, "andrew@...n.ch"
<andrew@...n.ch>, "f.fainelli@...il.com" <f.fainelli@...il.com>,
"olteanv@...il.com" <olteanv@...il.com>, "davem@...emloft.net"
<davem@...emloft.net>, "edumazet@...gle.com" <edumazet@...gle.com>,
"kuba@...nel.org" <kuba@...nel.org>, "pabeni@...hat.com" <pabeni@...hat.com>,
"arinc.unal@...nc9.com" <arinc.unal@...nc9.com>
Subject: Re: [PATCH net-next v2 3/7] net: dsa: realtek: common realtek-dsa
module
On Wed, Dec 20, 2023 at 01:24:26AM -0300, Luiz Angelo Daros de Luca wrote:
> Some code can be shared between both interface modules (MDIO and SMI)
> and among variants. These interface functions migrated to a common
> module:
>
> - realtek_common_lock
> - realtek_common_unlock
> - realtek_common_probe
> - realtek_common_register_switch
> - realtek_common_remove
>
> The reset during probe was moved to the end of the common probe. This way,
> we avoid a reset if anything else fails.
>
> Signed-off-by: Luiz Angelo Daros de Luca <luizluca@...il.com>
> ---
> drivers/net/dsa/realtek/Makefile | 2 +
> drivers/net/dsa/realtek/realtek-common.c | 137 +++++++++++++++++++++++
> drivers/net/dsa/realtek/realtek-common.h | 16 +++
> drivers/net/dsa/realtek/realtek-mdio.c | 114 +++----------------
> drivers/net/dsa/realtek/realtek-smi.c | 117 +++----------------
> drivers/net/dsa/realtek/realtek.h | 6 +-
> drivers/net/dsa/realtek/rtl8365mb.c | 9 +-
> drivers/net/dsa/realtek/rtl8366rb.c | 9 +-
> 8 files changed, 199 insertions(+), 211 deletions(-)
> create mode 100644 drivers/net/dsa/realtek/realtek-common.c
> create mode 100644 drivers/net/dsa/realtek/realtek-common.h
>
> diff --git a/drivers/net/dsa/realtek/Makefile b/drivers/net/dsa/realtek/Makefile
> index 0aab57252a7c..f4f9c6340d5f 100644
> --- a/drivers/net/dsa/realtek/Makefile
> +++ b/drivers/net/dsa/realtek/Makefile
> @@ -1,4 +1,6 @@
> # SPDX-License-Identifier: GPL-2.0
> +obj-$(CONFIG_NET_DSA_REALTEK) += realtek-dsa.o
> +realtek-dsa-objs := realtek-common.o
> obj-$(CONFIG_NET_DSA_REALTEK_MDIO) += realtek-mdio.o
> obj-$(CONFIG_NET_DSA_REALTEK_SMI) += realtek-smi.o
> obj-$(CONFIG_NET_DSA_REALTEK_RTL8366RB) += rtl8366.o
> diff --git a/drivers/net/dsa/realtek/realtek-common.c b/drivers/net/dsa/realtek/realtek-common.c
> new file mode 100644
> index 000000000000..c7507b6cdcdd
> --- /dev/null
> +++ b/drivers/net/dsa/realtek/realtek-common.c
> @@ -0,0 +1,137 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +
> +#include <linux/module.h>
> +
> +#include "realtek.h"
> +#include "realtek-common.h"
> +
> +void realtek_common_lock(void *ctx)
> +{
> + struct realtek_priv *priv = ctx;
> +
> + mutex_lock(&priv->map_lock);
> +}
> +EXPORT_SYMBOL_GPL(realtek_common_lock);
> +
> +void realtek_common_unlock(void *ctx)
> +{
> + struct realtek_priv *priv = ctx;
> +
> + mutex_unlock(&priv->map_lock);
> +}
> +EXPORT_SYMBOL_GPL(realtek_common_unlock);
> +
> +/* sets up driver private data struct, sets up regmaps, parse common device-tree
> + * properties and finally issues a hardware reset.
> + */
Please use kdoc format if you add such comments. But I think we agreed
that the name is quite informative now, so you can also just drop it.
> +struct realtek_priv *
> +realtek_common_probe(struct device *dev, struct regmap_config rc,
> + struct regmap_config rc_nolock)
> +{
> + const struct realtek_variant *var;
> + struct realtek_priv *priv;
> + int ret;
> +
> + var = of_device_get_match_data(dev);
> + if (!var)
> + return ERR_PTR(-EINVAL);
> +
> + priv = devm_kzalloc(dev, size_add(sizeof(*priv), var->chip_data_sz),
> + GFP_KERNEL);
> + if (!priv)
> + return ERR_PTR(-ENOMEM);
> +
> + mutex_init(&priv->map_lock);
> +
> + rc.lock_arg = priv;
> + priv->map = devm_regmap_init(dev, NULL, priv, &rc);
> + if (IS_ERR(priv->map)) {
> + ret = PTR_ERR(priv->map);
> + dev_err(dev, "regmap init failed: %d\n", ret);
> + return ERR_PTR(ret);
> + }
> +
> + priv->map_nolock = devm_regmap_init(dev, NULL, priv, &rc_nolock);
> + if (IS_ERR(priv->map_nolock)) {
> + ret = PTR_ERR(priv->map_nolock);
> + dev_err(dev, "regmap init failed: %d\n", ret);
> + return ERR_PTR(ret);
> + }
> +
> + /* Link forward and backward */
> + priv->dev = dev;
> + priv->variant = var;
> + priv->ops = var->ops;
> + priv->chip_data = (void *)priv + sizeof(*priv);
> +
> + dev_set_drvdata(dev, priv);
> + spin_lock_init(&priv->lock);
> +
> + priv->leds_disabled = of_property_read_bool(dev->of_node,
> + "realtek,disable-leds");
> +
> + /* TODO: if power is software controlled, set up any regulators here */
> +
> + priv->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> + if (IS_ERR(priv->reset)) {
> + dev_err(dev, "failed to get RESET GPIO\n");
> + return ERR_CAST(priv->reset);
> + }
> + if (priv->reset) {
> + gpiod_set_value(priv->reset, 1);
> + dev_dbg(dev, "asserted RESET\n");
> + msleep(REALTEK_HW_STOP_DELAY);
> + gpiod_set_value(priv->reset, 0);
> + msleep(REALTEK_HW_START_DELAY);
> + dev_dbg(dev, "deasserted RESET\n");
> + }
I simply cannot understand why you insist on moving this part despite
our earlier discussion on it where I pointed out that it makes no
sense to move it. Is chip hardware reset not the discipline of the chip
variant driver?
Why don't you just keep it in its original place? It will make your
patch smaller, which is what you seemed to care about the last time I
raised this.
Sorry, but I cannot give my Reviewed-by on this patch with this part
moved around.
> +
> + return priv;
> +}
> +EXPORT_SYMBOL(realtek_common_probe);
> +
> +/* Detects the realtek switch id/version and registers the dsa switch.
> + */
> +int realtek_common_register_switch(struct realtek_priv *priv)
> +{
> + int ret;
> +
> + ret = priv->ops->detect(priv);
> + if (ret) {
> + dev_err_probe(priv->dev, ret, "unable to detect switch\n");
> + return ret;
> + }
> +
> + priv->ds = devm_kzalloc(priv->dev, sizeof(*priv->ds), GFP_KERNEL);
> + if (!priv->ds)
> + return -ENOMEM;
> +
> + priv->ds->priv = priv;
> + priv->ds->dev = priv->dev;
> + priv->ds->ops = priv->ds_ops;
> + priv->ds->num_ports = priv->num_ports;
> +
> + ret = dsa_register_switch(priv->ds);
> + if (ret) {
> + dev_err_probe(priv->dev, ret, "unable to register switch\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(realtek_common_register_switch);
> +
> +void realtek_common_remove(struct realtek_priv *priv)
> +{
> + if (!priv)
> + return;
This check is not really necessary.
> +
> + /* leave the device reset asserted */
> + if (priv->reset)
> + gpiod_set_value(priv->reset, 1);
> +}
> +EXPORT_SYMBOL(realtek_common_remove);
> +
> +MODULE_AUTHOR("Luiz Angelo Daros de Luca <luizluca@...il.com>");
> +MODULE_DESCRIPTION("Realtek DSA switches common module");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/net/dsa/realtek/realtek-common.h b/drivers/net/dsa/realtek/realtek-common.h
> new file mode 100644
> index 000000000000..518d091ff496
> --- /dev/null
> +++ b/drivers/net/dsa/realtek/realtek-common.h
> @@ -0,0 +1,16 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +
> +#ifndef _REALTEK_COMMON_H
> +#define _REALTEK_COMMON_H
> +
> +#include <linux/regmap.h>
> +
> +void realtek_common_lock(void *ctx);
> +void realtek_common_unlock(void *ctx);
> +struct realtek_priv *
> +realtek_common_probe(struct device *dev, struct regmap_config rc,
> + struct regmap_config rc_nolock);
> +int realtek_common_register_switch(struct realtek_priv *priv);
> +void realtek_common_remove(struct realtek_priv *priv);
> +
> +#endif /* _REALTEK_COMMON_H */
> diff --git a/drivers/net/dsa/realtek/realtek-mdio.c b/drivers/net/dsa/realtek/realtek-mdio.c
> index 58966d0625c8..1eed09ab3aa1 100644
> --- a/drivers/net/dsa/realtek/realtek-mdio.c
> +++ b/drivers/net/dsa/realtek/realtek-mdio.c
> @@ -26,6 +26,7 @@
>
> #include "realtek.h"
> #include "realtek-mdio.h"
> +#include "realtek-common.h"
>
> /* Read/write via mdiobus */
> #define REALTEK_MDIO_CTRL0_REG 31
> @@ -100,20 +101,6 @@ static int realtek_mdio_read(void *ctx, u32 reg, u32 *val)
> return ret;
> }
>
> -static void realtek_mdio_lock(void *ctx)
> -{
> - struct realtek_priv *priv = ctx;
> -
> - mutex_lock(&priv->map_lock);
> -}
> -
> -static void realtek_mdio_unlock(void *ctx)
> -{
> - struct realtek_priv *priv = ctx;
> -
> - mutex_unlock(&priv->map_lock);
> -}
> -
> static const struct regmap_config realtek_mdio_regmap_config = {
> .reg_bits = 10, /* A4..A0 R4..R0 */
> .val_bits = 16,
> @@ -124,8 +111,8 @@ static const struct regmap_config realtek_mdio_regmap_config = {
> .reg_read = realtek_mdio_read,
> .reg_write = realtek_mdio_write,
> .cache_type = REGCACHE_NONE,
> - .lock = realtek_mdio_lock,
> - .unlock = realtek_mdio_unlock,
> + .lock = realtek_common_lock,
> + .unlock = realtek_common_unlock,
> };
>
> static const struct regmap_config realtek_mdio_nolock_regmap_config = {
> @@ -143,96 +130,23 @@ static const struct regmap_config realtek_mdio_nolock_regmap_config = {
>
> int realtek_mdio_probe(struct mdio_device *mdiodev)
> {
> - struct realtek_priv *priv;
> struct device *dev = &mdiodev->dev;
> - const struct realtek_variant *var;
> - struct regmap_config rc;
> - struct device_node *np;
> + struct realtek_priv *priv;
> int ret;
>
> - var = of_device_get_match_data(dev);
> - if (!var)
> - return -EINVAL;
> -
> - priv = devm_kzalloc(&mdiodev->dev,
> - size_add(sizeof(*priv), var->chip_data_sz),
> - GFP_KERNEL);
> - if (!priv)
> - return -ENOMEM;
> -
> - mutex_init(&priv->map_lock);
> + priv = realtek_common_probe(dev, realtek_mdio_regmap_config,
> + realtek_mdio_nolock_regmap_config);
> + if (IS_ERR(priv))
> + return PTR_ERR(priv);
>
> - rc = realtek_mdio_regmap_config;
> - rc.lock_arg = priv;
> - priv->map = devm_regmap_init(dev, NULL, priv, &rc);
> - if (IS_ERR(priv->map)) {
> - ret = PTR_ERR(priv->map);
> - dev_err(dev, "regmap init failed: %d\n", ret);
> - return ret;
> - }
> -
> - rc = realtek_mdio_nolock_regmap_config;
> - priv->map_nolock = devm_regmap_init(dev, NULL, priv, &rc);
> - if (IS_ERR(priv->map_nolock)) {
> - ret = PTR_ERR(priv->map_nolock);
> - dev_err(dev, "regmap init failed: %d\n", ret);
> - return ret;
> - }
> -
> - priv->mdio_addr = mdiodev->addr;
> priv->bus = mdiodev->bus;
> - priv->dev = &mdiodev->dev;
> - priv->chip_data = (void *)priv + sizeof(*priv);
> -
> - priv->clk_delay = var->clk_delay;
> - priv->cmd_read = var->cmd_read;
> - priv->cmd_write = var->cmd_write;
> - priv->ops = var->ops;
> -
> + priv->mdio_addr = mdiodev->addr;
> priv->write_reg_noack = realtek_mdio_write;
> + priv->ds_ops = priv->variant->ds_ops_mdio;
>
> - np = dev->of_node;
> -
> - dev_set_drvdata(dev, priv);
> -
> - /* TODO: if power is software controlled, set up any regulators here */
> - priv->leds_disabled = of_property_read_bool(np, "realtek,disable-leds");
> -
> - priv->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> - if (IS_ERR(priv->reset)) {
> - dev_err(dev, "failed to get RESET GPIO\n");
> - return PTR_ERR(priv->reset);
> - }
> -
> - if (priv->reset) {
> - gpiod_set_value(priv->reset, 1);
> - dev_dbg(dev, "asserted RESET\n");
> - msleep(REALTEK_HW_STOP_DELAY);
> - gpiod_set_value(priv->reset, 0);
> - msleep(REALTEK_HW_START_DELAY);
> - dev_dbg(dev, "deasserted RESET\n");
> - }
> -
> - ret = priv->ops->detect(priv);
> - if (ret) {
> - dev_err(dev, "unable to detect switch\n");
> - return ret;
> - }
> -
> - priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL);
> - if (!priv->ds)
> - return -ENOMEM;
> -
> - priv->ds->dev = dev;
> - priv->ds->num_ports = priv->num_ports;
> - priv->ds->priv = priv;
> - priv->ds->ops = var->ds_ops_mdio;
> -
> - ret = dsa_register_switch(priv->ds);
> - if (ret) {
> - dev_err(priv->dev, "unable to register switch ret = %d\n", ret);
> + ret = realtek_common_register_switch(priv);
> + if (ret)
> return ret;
> - }
>
> return 0;
> }
> @@ -247,9 +161,7 @@ void realtek_mdio_remove(struct mdio_device *mdiodev)
>
> dsa_unregister_switch(priv->ds);
>
> - /* leave the device reset asserted */
> - if (priv->reset)
> - gpiod_set_value(priv->reset, 1);
> + realtek_common_remove(priv);
> }
> EXPORT_SYMBOL_GPL(realtek_mdio_remove);
>
> diff --git a/drivers/net/dsa/realtek/realtek-smi.c b/drivers/net/dsa/realtek/realtek-smi.c
> index 31ac409acfd0..fc54190839cf 100644
> --- a/drivers/net/dsa/realtek/realtek-smi.c
> +++ b/drivers/net/dsa/realtek/realtek-smi.c
> @@ -41,12 +41,13 @@
>
> #include "realtek.h"
> #include "realtek-smi.h"
> +#include "realtek-common.h"
>
> #define REALTEK_SMI_ACK_RETRY_COUNT 5
>
> static inline void realtek_smi_clk_delay(struct realtek_priv *priv)
> {
> - ndelay(priv->clk_delay);
> + ndelay(priv->variant->clk_delay);
> }
>
> static void realtek_smi_start(struct realtek_priv *priv)
> @@ -209,7 +210,7 @@ static int realtek_smi_read_reg(struct realtek_priv *priv, u32 addr, u32 *data)
> realtek_smi_start(priv);
>
> /* Send READ command */
> - ret = realtek_smi_write_byte(priv, priv->cmd_read);
> + ret = realtek_smi_write_byte(priv, priv->variant->cmd_read);
> if (ret)
> goto out;
>
> @@ -250,7 +251,7 @@ static int realtek_smi_write_reg(struct realtek_priv *priv,
> realtek_smi_start(priv);
>
> /* Send WRITE command */
> - ret = realtek_smi_write_byte(priv, priv->cmd_write);
> + ret = realtek_smi_write_byte(priv, priv->variant->cmd_write);
> if (ret)
> goto out;
>
> @@ -311,20 +312,6 @@ static int realtek_smi_read(void *ctx, u32 reg, u32 *val)
> return realtek_smi_read_reg(priv, reg, val);
> }
>
> -static void realtek_smi_lock(void *ctx)
> -{
> - struct realtek_priv *priv = ctx;
> -
> - mutex_lock(&priv->map_lock);
> -}
> -
> -static void realtek_smi_unlock(void *ctx)
> -{
> - struct realtek_priv *priv = ctx;
> -
> - mutex_unlock(&priv->map_lock);
> -}
> -
> static const struct regmap_config realtek_smi_regmap_config = {
> .reg_bits = 10, /* A4..A0 R4..R0 */
> .val_bits = 16,
> @@ -335,8 +322,8 @@ static const struct regmap_config realtek_smi_regmap_config = {
> .reg_read = realtek_smi_read,
> .reg_write = realtek_smi_write,
> .cache_type = REGCACHE_NONE,
> - .lock = realtek_smi_lock,
> - .unlock = realtek_smi_unlock,
> + .lock = realtek_common_lock,
> + .unlock = realtek_common_unlock,
> };
>
> static const struct regmap_config realtek_smi_nolock_regmap_config = {
> @@ -411,99 +398,32 @@ static int realtek_smi_setup_mdio(struct dsa_switch *ds)
>
> int realtek_smi_probe(struct platform_device *pdev)
> {
> - const struct realtek_variant *var;
> struct device *dev = &pdev->dev;
> struct realtek_priv *priv;
> - struct regmap_config rc;
> - struct device_node *np;
> int ret;
>
> - var = of_device_get_match_data(dev);
> - np = dev->of_node;
> -
> - priv = devm_kzalloc(dev, sizeof(*priv) + var->chip_data_sz, GFP_KERNEL);
> - if (!priv)
> - return -ENOMEM;
> - priv->chip_data = (void *)priv + sizeof(*priv);
> -
> - mutex_init(&priv->map_lock);
> -
> - rc = realtek_smi_regmap_config;
> - rc.lock_arg = priv;
> - priv->map = devm_regmap_init(dev, NULL, priv, &rc);
> - if (IS_ERR(priv->map)) {
> - ret = PTR_ERR(priv->map);
> - dev_err(dev, "regmap init failed: %d\n", ret);
> - return ret;
> - }
> -
> - rc = realtek_smi_nolock_regmap_config;
> - priv->map_nolock = devm_regmap_init(dev, NULL, priv, &rc);
> - if (IS_ERR(priv->map_nolock)) {
> - ret = PTR_ERR(priv->map_nolock);
> - dev_err(dev, "regmap init failed: %d\n", ret);
> - return ret;
> - }
> -
> - /* Link forward and backward */
> - priv->dev = dev;
> - priv->clk_delay = var->clk_delay;
> - priv->cmd_read = var->cmd_read;
> - priv->cmd_write = var->cmd_write;
You don't mention these parts in your commit message. Could be a patch
in its own right too.
> - priv->ops = var->ops;
> -
> - priv->setup_interface = realtek_smi_setup_mdio;
> - priv->write_reg_noack = realtek_smi_write_reg_noack;
> -
> - dev_set_drvdata(dev, priv);
> - spin_lock_init(&priv->lock);
> -
> - /* TODO: if power is software controlled, set up any regulators here */
> -
> - priv->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> - if (IS_ERR(priv->reset)) {
> - dev_err(dev, "failed to get RESET GPIO\n");
> - return PTR_ERR(priv->reset);
> - }
> - if (priv->reset) {
> - gpiod_set_value(priv->reset, 1);
> - dev_dbg(dev, "asserted RESET\n");
> - msleep(REALTEK_HW_STOP_DELAY);
> - gpiod_set_value(priv->reset, 0);
> - msleep(REALTEK_HW_START_DELAY);
> - dev_dbg(dev, "deasserted RESET\n");
> - }
> + priv = realtek_common_probe(dev, realtek_smi_regmap_config,
> + realtek_smi_nolock_regmap_config);
> + if (IS_ERR(priv))
> + return PTR_ERR(priv);
>
> /* Fetch MDIO pins */
> priv->mdc = devm_gpiod_get_optional(dev, "mdc", GPIOD_OUT_LOW);
> if (IS_ERR(priv->mdc))
> return PTR_ERR(priv->mdc);
> +
> priv->mdio = devm_gpiod_get_optional(dev, "mdio", GPIOD_OUT_LOW);
> if (IS_ERR(priv->mdio))
> return PTR_ERR(priv->mdio);
>
> - priv->leds_disabled = of_property_read_bool(np, "realtek,disable-leds");
> + priv->write_reg_noack = realtek_smi_write_reg_noack;
> + priv->setup_interface = realtek_smi_setup_mdio;
> + priv->ds_ops = priv->variant->ds_ops_smi;
>
> - ret = priv->ops->detect(priv);
> - if (ret) {
> - dev_err(dev, "unable to detect switch\n");
> + ret = realtek_common_register_switch(priv);
> + if (ret)
> return ret;
> - }
> -
> - priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL);
> - if (!priv->ds)
> - return -ENOMEM;
>
> - priv->ds->dev = dev;
> - priv->ds->num_ports = priv->num_ports;
> - priv->ds->priv = priv;
> -
> - priv->ds->ops = var->ds_ops_smi;
> - ret = dsa_register_switch(priv->ds);
> - if (ret) {
> - dev_err_probe(dev, ret, "unable to register switch\n");
> - return ret;
> - }
> return 0;
> }
> EXPORT_SYMBOL_GPL(realtek_smi_probe);
> @@ -516,12 +436,11 @@ void realtek_smi_remove(struct platform_device *pdev)
> return;
>
> dsa_unregister_switch(priv->ds);
> +
> if (priv->user_mii_bus)
> of_node_put(priv->user_mii_bus->dev.of_node);
>
> - /* leave the device reset asserted */
> - if (priv->reset)
> - gpiod_set_value(priv->reset, 1);
> + realtek_common_remove(priv);
> }
> EXPORT_SYMBOL_GPL(realtek_smi_remove);
>
> diff --git a/drivers/net/dsa/realtek/realtek.h b/drivers/net/dsa/realtek/realtek.h
> index e9ee778665b2..fbd0616c1df3 100644
> --- a/drivers/net/dsa/realtek/realtek.h
> +++ b/drivers/net/dsa/realtek/realtek.h
> @@ -58,11 +58,9 @@ struct realtek_priv {
> struct mii_bus *bus;
> int mdio_addr;
>
> - unsigned int clk_delay;
> - u8 cmd_read;
> - u8 cmd_write;
> spinlock_t lock; /* Locks around command writes */
> struct dsa_switch *ds;
> + const struct dsa_switch_ops *ds_ops;
> struct irq_domain *irqdomain;
> bool leds_disabled;
>
> @@ -79,6 +77,8 @@ struct realtek_priv {
> int vlan_enabled;
> int vlan4k_enabled;
>
> + const struct realtek_variant *variant;
> +
> char buf[4096];
> void *chip_data; /* Per-chip extra variant data */
> };
> diff --git a/drivers/net/dsa/realtek/rtl8365mb.c b/drivers/net/dsa/realtek/rtl8365mb.c
> index 1ace2239934a..58ec057b6c32 100644
> --- a/drivers/net/dsa/realtek/rtl8365mb.c
> +++ b/drivers/net/dsa/realtek/rtl8365mb.c
> @@ -103,6 +103,7 @@
> #include "realtek.h"
> #include "realtek-smi.h"
> #include "realtek-mdio.h"
> +#include "realtek-common.h"
>
> /* Family-specific data and limits */
> #define RTL8365MB_PHYADDRMAX 7
> @@ -691,7 +692,7 @@ static int rtl8365mb_phy_ocp_read(struct realtek_priv *priv, int phy,
> u32 val;
> int ret;
>
> - mutex_lock(&priv->map_lock);
> + realtek_common_lock(priv);
>
> ret = rtl8365mb_phy_poll_busy(priv);
> if (ret)
> @@ -724,7 +725,7 @@ static int rtl8365mb_phy_ocp_read(struct realtek_priv *priv, int phy,
> *data = val & 0xFFFF;
>
> out:
> - mutex_unlock(&priv->map_lock);
> + realtek_common_unlock(priv);
>
> return ret;
> }
> @@ -735,7 +736,7 @@ static int rtl8365mb_phy_ocp_write(struct realtek_priv *priv, int phy,
> u32 val;
> int ret;
>
> - mutex_lock(&priv->map_lock);
> + realtek_common_lock(priv);
>
> ret = rtl8365mb_phy_poll_busy(priv);
> if (ret)
> @@ -766,7 +767,7 @@ static int rtl8365mb_phy_ocp_write(struct realtek_priv *priv, int phy,
> goto out;
>
> out:
> - mutex_unlock(&priv->map_lock);
> + realtek_common_unlock(priv);
>
> return 0;
> }
> diff --git a/drivers/net/dsa/realtek/rtl8366rb.c b/drivers/net/dsa/realtek/rtl8366rb.c
> index cc2fd636ec23..e60a0a81d426 100644
> --- a/drivers/net/dsa/realtek/rtl8366rb.c
> +++ b/drivers/net/dsa/realtek/rtl8366rb.c
> @@ -24,6 +24,7 @@
> #include "realtek.h"
> #include "realtek-smi.h"
> #include "realtek-mdio.h"
> +#include "realtek-common.h"
>
> #define RTL8366RB_PORT_NUM_CPU 5
> #define RTL8366RB_NUM_PORTS 6
> @@ -1707,7 +1708,7 @@ static int rtl8366rb_phy_read(struct realtek_priv *priv, int phy, int regnum)
> if (phy > RTL8366RB_PHY_NO_MAX)
> return -EINVAL;
>
> - mutex_lock(&priv->map_lock);
> + realtek_common_lock(priv);
>
> ret = regmap_write(priv->map_nolock, RTL8366RB_PHY_ACCESS_CTRL_REG,
> RTL8366RB_PHY_CTRL_READ);
> @@ -1735,7 +1736,7 @@ static int rtl8366rb_phy_read(struct realtek_priv *priv, int phy, int regnum)
> phy, regnum, reg, val);
>
> out:
> - mutex_unlock(&priv->map_lock);
> + realtek_common_unlock(priv);
>
> return ret;
> }
> @@ -1749,7 +1750,7 @@ static int rtl8366rb_phy_write(struct realtek_priv *priv, int phy, int regnum,
> if (phy > RTL8366RB_PHY_NO_MAX)
> return -EINVAL;
>
> - mutex_lock(&priv->map_lock);
> + realtek_common_lock(priv);
>
> ret = regmap_write(priv->map_nolock, RTL8366RB_PHY_ACCESS_CTRL_REG,
> RTL8366RB_PHY_CTRL_WRITE);
> @@ -1766,7 +1767,7 @@ static int rtl8366rb_phy_write(struct realtek_priv *priv, int phy, int regnum,
> goto out;
>
> out:
> - mutex_unlock(&priv->map_lock);
> + realtek_common_unlock(priv);
>
> return ret;
> }
> --
> 2.43.0
>
Powered by blists - more mailing lists