[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <8b80ab09-8444-4c3d-83b0-c7dbf5e58658@quicinc.com>
Date: Wed, 20 Dec 2023 13:02:45 +0530
From: Sneh Shah <quic_snehshah@...cinc.com>
To: Andrew Halaney <ahalaney@...hat.com>
CC: Vinod Koul <vkoul@...nel.org>, Bhupesh Sharma <bhupesh.sharma@...aro.org>,
Alexandre Torgue <alexandre.torgue@...s.st.com>,
Jose Abreu
<joabreu@...opsys.com>,
"David S. Miller" <davem@...emloft.net>,
Eric Dumazet
<edumazet@...gle.com>, Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni
<pabeni@...hat.com>,
Maxime Coquelin <mcoquelin.stm32@...il.com>, <netdev@...r.kernel.org>,
<linux-arm-msm@...r.kernel.org>,
<linux-stm32@...md-mailman.stormreply.com>,
<linux-arm-kernel@...ts.infradead.org>, <linux-kernel@...r.kernel.org>,
<kernel@...cinc.com>
Subject: Re: [PATCH net-next] net: stmmac: dwmac-qcom-ethqos: Add support for
2.5G SGMII
On 12/18/2023 9:50 PM, Andrew Halaney wrote:
> On Mon, Dec 18, 2023 at 12:41:18PM +0530, Sneh Shah wrote:
>> Serdes phy needs to operate at 2500 mode for 2.5G speed and 1000
>> mode for 1G/100M/10M speed.
>> Added changes to configure serdes phy and mac based on link speed.
>>
>> Signed-off-by: Sneh Shah <quic_snehshah@...cinc.com>
>> ---
>> .../stmicro/stmmac/dwmac-qcom-ethqos.c | 31 +++++++++++++++++--
>> 1 file changed, 29 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
>> index d3bf42d0fceb..b3a28dc19161 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
>> @@ -21,6 +21,7 @@
>> #define RGMII_IO_MACRO_CONFIG2 0x1C
>> #define RGMII_IO_MACRO_DEBUG1 0x20
>> #define EMAC_SYSTEM_LOW_POWER_DEBUG 0x28
>> +#define ETHQOS_MAC_AN_CTRL 0xE0
>>
>> /* RGMII_IO_MACRO_CONFIG fields */
>> #define RGMII_CONFIG_FUNC_CLK_EN BIT(30)
>> @@ -78,6 +79,10 @@
>> #define ETHQOS_MAC_CTRL_SPEED_MODE BIT(14)
>> #define ETHQOS_MAC_CTRL_PORT_SEL BIT(15)
>>
>> +/*ETHQOS_MAC_AN_CTRL bits */
>> +#define ETHQOS_MAC_AN_CTRL_RAN BIT(9)
>> +#define ETHQOS_MAC_AN_CTRL_ANE BIT(12)
>> +
>
> nit: space please add a space before ETHQOS_MAC_AN_CTRL
>
will take care of this in next patch
>> struct ethqos_emac_por {
>> unsigned int offset;
>> unsigned int value;
>> @@ -109,6 +114,7 @@ struct qcom_ethqos {
>> unsigned int num_por;
>> bool rgmii_config_loopback_en;
>> bool has_emac_ge_3;
>> + unsigned int serdes_speed;
>> };
>>
>> static int rgmii_readl(struct qcom_ethqos *ethqos, unsigned int offset)
>> @@ -600,27 +606,47 @@ static int ethqos_configure_rgmii(struct qcom_ethqos *ethqos)
>>
>> static int ethqos_configure_sgmii(struct qcom_ethqos *ethqos)
>> {
>> - int val;
>> -
>> + int val, mac_an_value;
>> val = readl(ethqos->mac_base + MAC_CTRL_REG);
>> + mac_an_value = readl(ethqos->mac_base + ETHQOS_MAC_AN_CTRL);
>>
>> switch (ethqos->speed) {
>> + case SPEED_2500:
>> + val &= ~ETHQOS_MAC_CTRL_PORT_SEL;
>> + rgmii_updatel(ethqos, RGMII_CONFIG2_RGMII_CLK_SEL_CFG,
>> + RGMII_CONFIG2_RGMII_CLK_SEL_CFG,
>> + RGMII_IO_MACRO_CONFIG2);
>> + if (ethqos->serdes_speed != SPEED_2500)
>> + phy_set_speed(ethqos->serdes_phy, ethqos->speed);
>> + mac_an_value &= ~ETHQOS_MAC_AN_CTRL_ANE;
>> + break;
>> case SPEED_1000:
>> val &= ~ETHQOS_MAC_CTRL_PORT_SEL;
>> rgmii_updatel(ethqos, RGMII_CONFIG2_RGMII_CLK_SEL_CFG,
>> RGMII_CONFIG2_RGMII_CLK_SEL_CFG,
>> RGMII_IO_MACRO_CONFIG2);
>> + if (ethqos->serdes_speed != SPEED_1000)
>> + phy_set_speed(ethqos->serdes_phy, ethqos->speed);
>> + mac_an_value |= ETHQOS_MAC_AN_CTRL_RAN | ETHQOS_MAC_AN_CTRL_ANE;
>> break;
>> case SPEED_100:
>> val |= ETHQOS_MAC_CTRL_PORT_SEL | ETHQOS_MAC_CTRL_SPEED_MODE;
>> + if (ethqos->serdes_speed != SPEED_1000)
>> + phy_set_speed(ethqos->serdes_phy, ethqos->speed);
>> + mac_an_value |= ETHQOS_MAC_AN_CTRL_RAN | ETHQOS_MAC_AN_CTRL_ANE;
>> break;
>> case SPEED_10:
>> val |= ETHQOS_MAC_CTRL_PORT_SEL;
>> val &= ~ETHQOS_MAC_CTRL_SPEED_MODE;
>> + if (ethqos->serdes_speed != SPEED_1000)
>> + phy_set_speed(ethqos->serdes_phy, ethqos->speed);
>> + mac_an_value |= ETHQOS_MAC_AN_CTRL_RAN | ETHQOS_MAC_AN_CTRL_ANE;
>> break;
>> }
>>
>> writel(val, ethqos->mac_base + MAC_CTRL_REG);
>> + writel(mac_an_value, ethqos->mac_base + ETHQOS_MAC_AN_CTRL);
>> + ethqos->serdes_speed = ethqos->speed;
>
> I see these bits are generic and there's some functions in stmmac_pcs.h
> that muck with these...
>
> Could you help me understand if this really should be Qualcomm specific,
> or if this is something that should be considered for the more core bits
> of the driver? I feel in either case we should take advantage of the
> common definitions in that file if possible.
>
we do have function dwmac_ctrl_ane in core driver which updates same registers. However, it does not have the option to reset ANE bit, it can only set bits. For SPEED_2500 we need to reset ANE bit. Hence I am adding it here. Not sure if we can extend dwmac_ctrl_ane function to reset bits as well.
>>
>> return val;
>> }
>> @@ -789,6 +815,7 @@ static int qcom_ethqos_probe(struct platform_device *pdev)
>> "Failed to get serdes phy\n");
>>
>> ethqos->speed = SPEED_1000;
>> + ethqos->serdes_speed = SPEED_1000;
>> ethqos_update_link_clk(ethqos, SPEED_1000);
>> ethqos_set_func_clk_en(ethqos);
>>
>> --
>> 2.17.1
>>
>
Powered by blists - more mailing lists