[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20240113102529.80371-5-arinc.unal@arinc9.com>
Date: Sat, 13 Jan 2024 13:25:25 +0300
From: Arınç ÜNAL <arinc.unal@...nc9.com>
To: Arınç ÜNAL <arinc.unal@...nc9.com>,
Daniel Golle <daniel@...rotopia.org>,
Landen Chao <Landen.Chao@...iatek.com>,
DENG Qingfang <dqfext@...il.com>,
Sean Wang <sean.wang@...iatek.com>,
Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Vladimir Oltean <olteanv@...il.com>,
"David S. Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni <pabeni@...hat.com>,
Matthias Brugger <matthias.bgg@...il.com>,
AngeloGioacchino Del Regno <angelogioacchino.delregno@...labora.com>
Cc: mithat.guner@...ont.com,
erkin.bozoglu@...ont.com,
Luiz Angelo Daros de Luca <luizluca@...il.com>,
netdev@...r.kernel.org,
linux-kernel@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org,
linux-mediatek@...ts.infradead.org
Subject: [RFC PATCH net-next 4/8] net: dsa: mt7530: move XTAL check to mt7530_setup()
The crystal frequency concerns the switch core. The frequency should be
checked when the switch is being set up so the driver can reject the
unsupported hardware earlier and without requiring port 6 to be used.
Move it to mt7530_setup(). Drop the unnecessary function printing.
Signed-off-by: Arınç ÜNAL <arinc.unal@...nc9.com>
Reviewed-by: Andrew Lunn <andrew@...n.ch>
---
drivers/net/dsa/mt7530.c | 13 ++++++-------
1 file changed, 6 insertions(+), 7 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 823dc3ab15c8..d3e1e31ac8d0 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -422,13 +422,6 @@ mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
- if (xtal == HWTRAP_XTAL_20MHZ) {
- dev_err(priv->dev,
- "%s: MT7530 with a 20MHz XTAL is not supported!\n",
- __func__);
- return -EINVAL;
- }
-
switch (interface) {
case PHY_INTERFACE_MODE_RGMII:
trgint = 0;
@@ -2235,6 +2228,12 @@ mt7530_setup(struct dsa_switch *ds)
return -ENODEV;
}
+ if ((val & HWTRAP_XTAL_MASK) == HWTRAP_XTAL_20MHZ) {
+ dev_err(priv->dev,
+ "MT7530 with a 20MHz XTAL is not supported!\n");
+ return -EINVAL;
+ }
+
/* Reset the switch through internal reset */
mt7530_write(priv, MT7530_SYS_CTRL,
SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
--
2.40.1
Powered by blists - more mailing lists