[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <dc6f77bd-6671-43eb-8658-626b2591415d@collabora.com>
Date: Fri, 26 Jan 2024 10:12:48 +0100
From: AngeloGioacchino Del Regno <angelogioacchino.delregno@...labora.com>
To: Chen-Yu Tsai <wenst@...omium.org>
Cc: Marcel Holtmann <marcel@...tmann.org>,
Luiz Augusto von Dentz <luiz.dentz@...il.com>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>, Matthias Brugger
<matthias.bgg@...il.com>, Sean Wang <sean.wang@...iatek.com>,
linux-bluetooth@...r.kernel.org, netdev@...r.kernel.org,
linux-mediatek@...ts.infradead.org, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH 1/2] dt-bindings: net: bluetooth: Add MediaTek MT7921S
SDIO Bluetooth
Il 26/01/24 04:26, Chen-Yu Tsai ha scritto:
> On Thu, Jan 25, 2024 at 7:39 PM AngeloGioacchino Del Regno
> <angelogioacchino.delregno@...labora.com> wrote:
>>
>> Il 25/01/24 10:52, Chen-Yu Tsai ha scritto:
>>> The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
>>> SDIO. While the Bluetooth function is fully discoverable, the chip
>>> has a pin that can reset just the Bluetooth side, as opposed to the
>>> full chip. This needs to be described in the device tree.
>>>
>>> Add a device tree binding for MT7921S Bluetooth over SDIO specifically
>>> ot document the reset line.
>>>
>>> Cc: Sean Wang <sean.wang@...iatek.com>
>>> Signed-off-by: Chen-Yu Tsai <wenst@...omium.org>
>>> ---
>>> .../bluetooth/mediatek,mt7921s-bluetooth.yaml | 49 +++++++++++++++++++
>>> MAINTAINERS | 1 +
>>> 2 files changed, 50 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
>>>
>>> diff --git a/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
>>> new file mode 100644
>>> index 000000000000..bbe240e7cc40
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
>>> @@ -0,0 +1,49 @@
>>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>>> +%YAML 1.2
>>> +---
>>> +$id: http://devicetree.org/schemas/net/bluetooth/mediatek,mt7921s-bluetooth.yaml#
>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>> +
>>> +title: MediaTek MT7921S Bluetooth
>>> +
>>
>> title:
>>
>> maintainers:
>>
>> description:
>>
>> ... and then, you missed
>>
>> allOf:
>> - $ref: bluetooth-controller.yaml#
>
> (facepalm)
>
>> Everything else looks good.
>>
>> Cheers,
>> Angelo
>>
>>> +description:
>>
>> MT7921S is a (dual?) SDIO-attached dual-radio WiFi+Bluetooth combo chip;
>> this chip has two dedicated reset lines, one of which is used to reset
>> the Bluetooth core.
>> The WiFi part of this chip is described in ....where? :-)
>
> The function itself is fully probable and the implementation doesn't make
> use of the WiFi's reset line, so I don't see any reason to describe it?
> I don't actually know what the reset line does in the chip hardware.
> This patch is just described what is already used.
>
>>> + This binding describes the Bluetooth side of the SDIO-attached MT7921S
>>> + WiFi+Bluetooth combo chips. These chips are dual-radio chips supporting
>>> + WiFi and Bluetooth. Bluetooth works over SDIO just like WiFi. Bluetooth
>>> + has its own reset line, separate from WiFi, which can be used to reset
>>> + the Bluetooth core.
>>> +
>>> +maintainers:
>>> + - Sean Wang <sean.wang@...iatek.com>
>>> +
>>> +properties:
>>> + compatible:
>>> + enum:
>>> + - mediatek,mt7921s-bluetooth
>>> + reg:
>>> + const: 2
>>> +
>>> + reset-gpios:
>>> + maxItems: 1
>>> + description: A GPIO line connected to the Bluetooth subsystem reset line.
>>> + Typically the W_DISABLE2# pin on M.2 E-key modules. If present this
>>> + shall be flagged as active low.
>>
>> description:
>> An active-low reset line connected for the Bluetooth core;
>
> connected to?
Eh yes, sorry - I edited that statement multiple times and that "for" stuck
there for reasons :-)
>
>> on typical M.2 Key-E modules this is the W_DISABLE2# pin.
>
> Otherwise this looks better. Thanks.
You're welcome!
Cheers!
>
>
> ChenYu
>
>> Cheers,
>> Angelo
>>
>>> +
>>> +required:
>>> + - compatible
>>> + - reg
>>> +
>>> +additionalProperties: false
>>> +
>>> +examples:
>>> + - |
>>> + mmc {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + bluetooth@2 {
>>> + compatible = "mediatek,mt7921s-bluetooth";
>>> + reg = <2>;
>>> + reset-gpios = <&pio 8 GPIO_ACTIVE_LOW>;
>>> + };
>>> + };
>>> diff --git a/MAINTAINERS b/MAINTAINERS
>>> index b64a64ca7916..662957146852 100644
>>> --- a/MAINTAINERS
>>> +++ b/MAINTAINERS
>>> @@ -13657,6 +13657,7 @@ M: Sean Wang <sean.wang@...iatek.com>
>>> L: linux-bluetooth@...r.kernel.org
>>> L: linux-mediatek@...ts.infradead.org (moderated for non-subscribers)
>>> S: Maintained
>>> +F: Documentation/devicetree/bindings/net/bluetooth/mediatek,mt7921s-bluetooth.yaml
>>> F: Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
>>> F: drivers/bluetooth/btmtkuart.c
>>>
>>
Powered by blists - more mailing lists