netdev - Re: [PATCH] phy: lynx-28g: use read_poll_timeout when waiting for halt/reset bits

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [day] [month] [year] [list]

Message-ID: <26eff838-9f87-452f-8bad-90ce3d389255@solid-run.com>
Date: Sun, 18 Feb 2024 15:21:33 +0100
From: Josua Mayer <josua@...id-run.com>
To: Ioana Ciornei <ioana.ciornei@....com>, Vinod Koul <vkoul@...nel.org>,
 Kishon Vijay Abraham I <kishon@...nel.org>
Cc: Jon Nettleton <jon@...id-run.com>, Rabeeh Khoury <rabeeh@...id-run.com>,
 Yazan Shhady <yazan.shhady@...id-run.com>, netdev@...r.kernel.org,
 linux-phy@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH] phy: lynx-28g: use read_poll_timeout when waiting for
 halt/reset bits

Am 18.02.24 um 15:09 schrieb Josua Mayer:

> Power-on and -off functions set and wait for self-clearing reset-
> and halt-bits in serdes registers.
> In certain operating conditions these bits may not actually clear.
>
> Replace the infinite while-loops with read_poll_timeout to ensure that
> power_on and power_off will always return even when the bits did not
> clear within a full second.
>
> On timeout print an error message and return error code.
> In this situation the serdes lane has an invalid state,
> without no known recovery procedure.
>
> This fixes an infinite loop / hang during boot observed on a
> misconfigured lx2160a system where serdes #1 PLLS (161MHz) and PLLF
> (100MHz) were mistakenly swapped.
> After reset the PLL's did lock (to wrong rates) but the serdes locked up
> and never cleared either lane-specific or global halt- and reset-bits.
>
> Signed-off-by: Josua Mayer <josua@...id-run.com>
> ---
>   drivers/phy/freescale/phy-fsl-lynx-28g.c | 42 ++++++++++++++++++++++++--------
>   1 file changed, 32 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/phy/freescale/phy-fsl-lynx-28g.c b/drivers/phy/freescale/phy-fsl-lynx-28g.c
> index e2187767ce00..5ae5b47619f8 100644
> --- a/drivers/phy/freescale/phy-fsl-lynx-28g.c
> +++ b/drivers/phy/freescale/phy-fsl-lynx-28g.c
> @@ -335,6 +335,7 @@ static int lynx_28g_power_off(struct phy *phy)
> ...
> +	err = read_poll_timeout(lynx_28g_lane_read, rrstctl,
> +				!(rrstctl & LYNX_28G_LNaRRSTCTL_HLT_REQ),
> +				10000, 1000000, false, lane, LNaRRSTCTL);
> +	if (err) {
> +		dev_err(&phy->dev, "tx lane halt failed: %d\n", err);
Message should be "rx" lane, will fix in v2.