[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id:
<20240301-for-netnext-mt7530-improvements-3-v3-3-449f4f166454@arinc9.com>
Date: Fri, 01 Mar 2024 12:42:59 +0200
From: Arınç ÜNAL via B4 Relay
<devnull+arinc.unal.arinc9.com@...nel.org>
To: Daniel Golle <daniel@...rotopia.org>, DENG Qingfang <dqfext@...il.com>,
Sean Wang <sean.wang@...iatek.com>, Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Vladimir Oltean <olteanv@...il.com>,
"David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
Matthias Brugger <matthias.bgg@...il.com>,
AngeloGioacchino Del Regno <angelogioacchino.delregno@...labora.com>,
Russell King <linux@...linux.org.uk>
Cc: mithat.guner@...ont.com, erkin.bozoglu@...ont.com,
Bartel Eerdekens <bartel.eerdekens@...stell8.be>, netdev@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-mediatek@...ts.infradead.org,
Arınç ÜNAL <arinc.unal@...nc9.com>
Subject: [PATCH net-next v3 3/9] net: dsa: mt7530: do not use SW_PHY_RST to
reset MT7531 switch
From: Arınç ÜNAL <arinc.unal@...nc9.com>
According to the document MT7531 Reference Manual for Development Board
v1.0, the SW_PHY_RST bit on the SYS_CTRL register doesn't exist for
MT7531. This is likely why forcing link down on all ports is necessary for
MT7531.
Therefore, do not set SW_PHY_RST on mt7531_setup().
Signed-off-by: Arınç ÜNAL <arinc.unal@...nc9.com>
---
drivers/net/dsa/mt7530.c | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 5cfd303b773f..296711fd5c43 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2451,14 +2451,12 @@ mt7531_setup(struct dsa_switch *ds)
val = mt7530_read(priv, MT7531_TOP_SIG_SR);
priv->p5_sgmii = !!(val & PAD_DUAL_SGMII_EN);
- /* all MACs must be forced link-down before sw reset */
+ /* Force link down on all ports before internal reset */
for (i = 0; i < MT7530_NUM_PORTS; i++)
mt7530_write(priv, MT7530_PMCR_P(i), MT7531_FORCE_LNK);
/* Reset the switch through internal reset */
- mt7530_write(priv, MT7530_SYS_CTRL,
- SYS_CTRL_PHY_RST | SYS_CTRL_SW_RST |
- SYS_CTRL_REG_RST);
+ mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_SW_RST | SYS_CTRL_REG_RST);
if (!priv->p5_sgmii) {
mt7531_pll_setup(priv);
--
2.40.1
Powered by blists - more mailing lists