[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id:
<20240301-for-netnext-mt7530-improvements-3-v3-9-449f4f166454@arinc9.com>
Date: Fri, 01 Mar 2024 12:43:05 +0200
From: Arınç ÜNAL via B4 Relay
<devnull+arinc.unal.arinc9.com@...nel.org>
To: Daniel Golle <daniel@...rotopia.org>, DENG Qingfang <dqfext@...il.com>,
Sean Wang <sean.wang@...iatek.com>, Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Vladimir Oltean <olteanv@...il.com>,
"David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
Matthias Brugger <matthias.bgg@...il.com>,
AngeloGioacchino Del Regno <angelogioacchino.delregno@...labora.com>,
Russell King <linux@...linux.org.uk>
Cc: mithat.guner@...ont.com, erkin.bozoglu@...ont.com,
Bartel Eerdekens <bartel.eerdekens@...stell8.be>, netdev@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-mediatek@...ts.infradead.org,
Arınç ÜNAL <arinc.unal@...nc9.com>
Subject: [PATCH net-next v3 9/9] net: dsa: mt7530: simplify link operations
From: Arınç ÜNAL <arinc.unal@...nc9.com>
The "MT7621 Giga Switch Programming Guide v0.3", "MT7531 Reference Manual
for Development Board v1.0", and "MT7988A Wi-Fi 7 Generation Router
Platform: Datasheet (Open Version) v0.1" documents show that these bits are
enabled at reset:
PMCR_IFG_XMIT(1) (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_MAC_MODE (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_EN
PMCR_RX_EN
PMCR_BACKOFF_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_BACKPR_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_FC_EN
PMCR_RX_FC_EN
These bits also don't exist on the MT7530_PMCR_P(6) register of the switch
on the MT7988 SoC:
PMCR_IFG_XMIT()
PMCR_MAC_MODE
PMCR_BACKOFF_EN
PMCR_BACKPR_EN
Remove the setting of the bits not part of PMCR_LINK_SETTINGS_MASK on
phylink_mac_config as they're already set.
The bit for setting the port on force mode is already done on
mt7530_setup() and mt7531_setup_common(). So get rid of
PMCR_FORCE_MODE_ID() which helped determine which bit to use for the switch
model.
Signed-off-by: Arınç ÜNAL <arinc.unal@...nc9.com>
---
drivers/net/dsa/mt7530.c | 12 +-----------
drivers/net/dsa/mt7530.h | 2 --
2 files changed, 1 insertion(+), 13 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 91d927bb49f7..1ae11b180d54 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2667,23 +2667,13 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
const struct phylink_link_state *state)
{
struct mt7530_priv *priv = ds->priv;
- u32 mcr_cur, mcr_new;
if ((port == 5 || port == 6) && priv->info->mac_port_config)
priv->info->mac_port_config(ds, port, mode, state->interface);
- mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
- mcr_new = mcr_cur;
- mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
- mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
- PMCR_BACKPR_EN | PMCR_FORCE_MODE_ID(priv->id);
-
/* Are we connected to external phy */
if (port == 5 && dsa_is_user_port(ds, 5))
- mcr_new |= PMCR_EXT_PHY;
-
- if (mcr_new != mcr_cur)
- mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
+ mt7530_set(priv, MT7530_PMCR_P(port), PMCR_EXT_PHY);
}
static void mt753x_phylink_mac_link_down(struct dsa_switch *ds, int port,
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index 8a8144868eaa..a71166e0a7fc 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -304,8 +304,6 @@ enum mt7530_vlan_port_acc_frm {
MT7531_FORCE_DPX | \
MT7531_FORCE_RX_FC | \
MT7531_FORCE_TX_FC)
-#define PMCR_FORCE_MODE_ID(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \
- MT7531_FORCE_MODE : PMCR_FORCE_MODE)
#define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
--
2.40.1
Powered by blists - more mailing lists