netdev - [Intel-wired-lan] [PATCH iwl-next v6 6/6] ice: Document tx_scheduling

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20240305143942.23757-7-mateusz.polchlopek@intel.com>
Date: Tue,  5 Mar 2024 09:39:42 -0500
From: Mateusz Polchlopek <mateusz.polchlopek@...el.com>
To: intel-wired-lan@...ts.osuosl.org
Cc: netdev@...r.kernel.org,
	anthony.l.nguyen@...el.com,
	kuba@...nel.org,
	jiri@...nulli.us,
	horms@...nel.org,
	przemyslaw.kitszel@...el.com,
	andrew@...n.ch,
	victor.raj@...el.com,
	michal.wilczynski@...el.com,
	lukasz.czapnik@...el.com,
	Mateusz Polchlopek <mateusz.polchlopek@...el.com>
Subject: [Intel-wired-lan] [PATCH iwl-next v6 6/6] ice: Document tx_scheduling_layers parameter

From: Michal Wilczynski <michal.wilczynski@...el.com>

New driver specific parameter 'tx_scheduling_layers' was introduced.
Describe parameter in the documentation.

Signed-off-by: Michal Wilczynski <michal.wilczynski@...el.com>
Acked-by: Jakub Kicinski <kuba@...nel.org>
Co-developed-by: Mateusz Polchlopek <mateusz.polchlopek@...el.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@...el.com>
---
 Documentation/networking/devlink/ice.rst | 47 ++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/Documentation/networking/devlink/ice.rst b/Documentation/networking/devlink/ice.rst
index 7f30ebd5debb..8fc8480e2d2b 100644
--- a/Documentation/networking/devlink/ice.rst
+++ b/Documentation/networking/devlink/ice.rst
@@ -21,6 +21,53 @@ Parameters
    * - ``enable_iwarp``
      - runtime
      - mutually exclusive with ``enable_roce``
+   * - ``tx_scheduling_layers``
+     - permanent
+     - The ice hardware uses hierarchical scheduling for Tx with a fixed
+       number of layers in the scheduling tree. Each of them are decision
+       points. Root node represents a port, while all the leaves represent
+       the queues. This way of configuring the Tx scheduler allows features
+       like DCB or devlink-rate (documented below) to configure how much
+       bandwidth is given to any given queue or group of queues, enabling
+       fine-grained control because scheduling parameters can be configured
+       at any given layer of the tree.
+
+       The default 9-layer tree topology was deemed best for most workloads,
+       as it gives an optimal ratio of performance to configurability. However,
+       for some specific cases, this 9-layer topology might not be desired.
+       One example would be sending traffic to queues that are not a multiple
+       of 8. Because the maximum radix is limited to 8 in 9-layer topology,
+       the 9th queue has a different parent than the rest, and it's given
+       more bandwidth credits. This causes a problem when the system is
+       sending traffic to 9 queues:
+
+       | tx_queue_0_packets: 24163396
+       | tx_queue_1_packets: 24164623
+       | tx_queue_2_packets: 24163188
+       | tx_queue_3_packets: 24163701
+       | tx_queue_4_packets: 24163683
+       | tx_queue_5_packets: 24164668
+       | tx_queue_6_packets: 23327200
+       | tx_queue_7_packets: 24163853
+       | tx_queue_8_packets: 91101417 < Too much traffic is sent from 9th
+
+       To address this need, you can switch to a 5-layer topology, which
+       changes the maximum topology radix to 512. With this enhancement,
+       the performance characteristic is equal as all queues can be assigned
+       to the same parent in the tree. The obvious drawback of this solution
+       is a lower configuration depth of the tree.
+
+       Use the ``tx_scheduling_layer`` parameter with the devlink command
+       to change the transmit scheduler topology. To use 5-layer topology,
+       use a value of 5. For example:
+       $ devlink dev param set pci/0000:16:00.0 name tx_scheduling_layers
+       value 5 cmode permanent
+       Use a value of 9 to set it back to the default value.
+
+       You must reboot the system for the selected topology to take effect.
+
+       To verify that value has been set:
+       $ devlink dev param show pci/0000:16:00.0 name tx_scheduling_layers
 
 Info versions
 =============
-- 
2.38.1