| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20240527151023.3634-4-piotr.kwapulinski@intel.com>
Date: Mon, 27 May 2024 17:10:19 +0200
From: Piotr Kwapulinski <piotr.kwapulinski@...el.com>
To: intel-wired-lan@...ts.osuosl.org
Cc: netdev@...r.kernel.org,
jacob.e.keller@...el.com,
Piotr Kwapulinski <piotr.kwapulinski@...el.com>,
Stefan Wegrzyn <stefan.wegrzyn@...el.com>,
Jedrzej Jagielski <jedrzej.jagielski@...el.com>,
Jan Glaza <jan.glaza@...el.com>
Subject: [PATCH iwl-next v7 3/7] ixgbe: Add link management support for E610 device
Add low level link management support for E610 device. Link management
operations are handled via the Admin Command Interface. Add the following
link management operations:
- get link capabilities
- set up link
- get media type
- get link status, link status events
- link power management
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@...el.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@...el.com>
Co-developed-by: Jedrzej Jagielski <jedrzej.jagielski@...el.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@...el.com>
Reviewed-by: Jan Glaza <jan.glaza@...el.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@...el.com>
---
drivers/net/ethernet/intel/ixgbe/ixgbe_e610.c | 1083 +++++++++++++++++
drivers/net/ethernet/intel/ixgbe/ixgbe_e610.h | 32 +
.../ethernet/intel/ixgbe/ixgbe_type_e610.h | 1 +
3 files changed, 1116 insertions(+)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_e610.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_e610.c
index 0afd1ad..b6c3259 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_e610.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_e610.c
@@ -1007,3 +1007,1086 @@ void ixgbe_copy_phy_caps_to_cfg(struct ixgbe_aci_cmd_get_phy_caps_data *caps,
cfg->module_compliance_enforcement =
caps->module_compliance_enforcement;
}
+
+/**
+ * ixgbe_aci_set_phy_cfg - set PHY configuration
+ * @hw: pointer to the HW struct
+ * @cfg: structure with PHY configuration data to be set
+ *
+ * Set the various PHY configuration parameters supported on the Port
+ * using ACI command (0x0601).
+ * One or more of the Set PHY config parameters may be ignored in an MFP
+ * mode as the PF may not have the privilege to set some of the PHY Config
+ * parameters.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_set_phy_cfg(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_set_phy_cfg_data *cfg)
+{
+ struct ixgbe_aci_desc desc;
+ int err;
+
+ if (!cfg)
+ return -EINVAL;
+
+ /* Ensure that only valid bits of cfg->caps can be turned on. */
+ cfg->caps &= IXGBE_ACI_PHY_ENA_VALID_MASK;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_set_phy_cfg);
+ desc.params.set_phy.lport_num = hw->bus.func;
+ desc.flags |= IXGBE_ACI_FLAG_RD;
+
+ err = ixgbe_aci_send_cmd(hw, &desc, cfg, sizeof(*cfg));
+
+ if (!err)
+ hw->phy.curr_user_phy_cfg = *cfg;
+
+ return err;
+}
+
+/**
+ * ixgbe_aci_set_link_restart_an - set up link and restart AN
+ * @hw: pointer to the HW struct
+ * @ena_link: if true: enable link, if false: disable link
+ *
+ * Function sets up the link and restarts the Auto-Negotiation over the link.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_set_link_restart_an(struct ixgbe_hw *hw, bool ena_link)
+{
+ struct ixgbe_aci_cmd_restart_an *cmd;
+ struct ixgbe_aci_desc desc;
+
+ cmd = &desc.params.restart_an;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_restart_an);
+
+ cmd->cmd_flags = IXGBE_ACI_RESTART_AN_LINK_RESTART;
+ cmd->lport_num = hw->bus.func;
+ if (ena_link)
+ cmd->cmd_flags |= IXGBE_ACI_RESTART_AN_LINK_ENABLE;
+ else
+ cmd->cmd_flags &= ~IXGBE_ACI_RESTART_AN_LINK_ENABLE;
+
+ return ixgbe_aci_send_cmd(hw, &desc, NULL, 0);
+}
+
+/**
+ * ixgbe_is_media_cage_present - check if media cage is present
+ * @hw: pointer to the HW struct
+ *
+ * Identify presence of media cage using the ACI command (0x06E0).
+ *
+ * Return: true if media cage is present, else false. If no cage, then
+ * media type is backplane or BASE-T.
+ */
+static bool ixgbe_is_media_cage_present(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_link_topo *cmd;
+ struct ixgbe_aci_desc desc;
+
+ cmd = &desc.params.get_link_topo;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_get_link_topo);
+
+ cmd->addr.topo_params.node_type_ctx =
+ FIELD_PREP(IXGBE_ACI_LINK_TOPO_NODE_CTX_M,
+ IXGBE_ACI_LINK_TOPO_NODE_CTX_PORT);
+
+ /* Set node type. */
+ cmd->addr.topo_params.node_type_ctx |=
+ (IXGBE_ACI_LINK_TOPO_NODE_TYPE_M &
+ IXGBE_ACI_LINK_TOPO_NODE_TYPE_CAGE);
+
+ /* Node type cage can be used to determine if cage is present. If AQC
+ * returns error (ENOENT), then no cage present. If no cage present then
+ * connection type is backplane or BASE-T.
+ */
+ return ixgbe_aci_get_netlist_node(hw, cmd, NULL, NULL);
+}
+
+/**
+ * ixgbe_get_media_type_from_phy_type - Gets media type based on phy type
+ * @hw: pointer to the HW struct
+ *
+ * Try to identify the media type based on the phy type.
+ * If more than one media type, the ixgbe_media_type_unknown is returned.
+ * First, phy_type_low is checked, then phy_type_high.
+ * If none are identified, the ixgbe_media_type_unknown is returned
+ *
+ * Return: type of a media based on phy type in form of enum.
+ */
+static enum ixgbe_media_type
+ixgbe_get_media_type_from_phy_type(struct ixgbe_hw *hw)
+{
+ struct ixgbe_link_status *hw_link_info;
+
+ if (!hw)
+ return ixgbe_media_type_unknown;
+
+ hw_link_info = &hw->link.link_info;
+ if (hw_link_info->phy_type_low && hw_link_info->phy_type_high)
+ /* If more than one media type is selected, report unknown */
+ return ixgbe_media_type_unknown;
+
+ if (hw_link_info->phy_type_low) {
+ /* 1G SGMII is a special case where some DA cable PHYs
+ * may show this as an option when it really shouldn't
+ * be since SGMII is meant to be between a MAC and a PHY
+ * in a backplane. Try to detect this case and handle it
+ */
+ if (hw_link_info->phy_type_low == IXGBE_PHY_TYPE_LOW_1G_SGMII &&
+ (hw_link_info->module_type[IXGBE_ACI_MOD_TYPE_IDENT] ==
+ IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_ACTIVE ||
+ hw_link_info->module_type[IXGBE_ACI_MOD_TYPE_IDENT] ==
+ IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_PASSIVE))
+ return ixgbe_media_type_da;
+
+ switch (hw_link_info->phy_type_low) {
+ case IXGBE_PHY_TYPE_LOW_1000BASE_SX:
+ case IXGBE_PHY_TYPE_LOW_1000BASE_LX:
+ case IXGBE_PHY_TYPE_LOW_10GBASE_SR:
+ case IXGBE_PHY_TYPE_LOW_10GBASE_LR:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_SR:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_LR:
+ return ixgbe_media_type_fiber;
+ case IXGBE_PHY_TYPE_LOW_10G_SFI_AOC_ACC:
+ case IXGBE_PHY_TYPE_LOW_25G_AUI_AOC_ACC:
+ return ixgbe_media_type_fiber;
+ case IXGBE_PHY_TYPE_LOW_100BASE_TX:
+ case IXGBE_PHY_TYPE_LOW_1000BASE_T:
+ case IXGBE_PHY_TYPE_LOW_2500BASE_T:
+ case IXGBE_PHY_TYPE_LOW_5GBASE_T:
+ case IXGBE_PHY_TYPE_LOW_10GBASE_T:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_T:
+ return ixgbe_media_type_copper;
+ case IXGBE_PHY_TYPE_LOW_10G_SFI_DA:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_CR:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_CR_S:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_CR1:
+ return ixgbe_media_type_da;
+ case IXGBE_PHY_TYPE_LOW_25G_AUI_C2C:
+ if (ixgbe_is_media_cage_present(hw))
+ return ixgbe_media_type_aui;
+ fallthrough;
+ case IXGBE_PHY_TYPE_LOW_1000BASE_KX:
+ case IXGBE_PHY_TYPE_LOW_2500BASE_KX:
+ case IXGBE_PHY_TYPE_LOW_2500BASE_X:
+ case IXGBE_PHY_TYPE_LOW_5GBASE_KR:
+ case IXGBE_PHY_TYPE_LOW_10GBASE_KR_CR1:
+ case IXGBE_PHY_TYPE_LOW_10G_SFI_C2C:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_KR:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_KR1:
+ case IXGBE_PHY_TYPE_LOW_25GBASE_KR_S:
+ return ixgbe_media_type_backplane;
+ }
+ } else {
+ switch (hw_link_info->phy_type_high) {
+ case IXGBE_PHY_TYPE_HIGH_10BASE_T:
+ return ixgbe_media_type_copper;
+ }
+ }
+ return ixgbe_media_type_unknown;
+}
+
+/**
+ * ixgbe_update_link_info - update status of the HW network link
+ * @hw: pointer to the HW struct
+ *
+ * Update the status of the HW network link.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_update_link_info(struct ixgbe_hw *hw)
+{
+ struct ixgbe_link_status *li;
+ int err;
+
+ if (!hw)
+ return -EINVAL;
+
+ li = &hw->link.link_info;
+
+ err = ixgbe_aci_get_link_info(hw, true, NULL);
+ if (err)
+ return err;
+
+ if (li->link_info & IXGBE_ACI_MEDIA_AVAILABLE) {
+ struct ixgbe_aci_cmd_get_phy_caps_data __free(kfree) *pcaps;
+
+ pcaps = kzalloc(sizeof(*pcaps), GFP_KERNEL);
+ if (!pcaps)
+ return -ENOMEM;
+
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_TOPO_CAP_MEDIA,
+ pcaps);
+
+ if (!err)
+ memcpy(li->module_type, &pcaps->module_type,
+ sizeof(li->module_type));
+ }
+
+ return err;
+}
+
+/**
+ * ixgbe_get_link_status - get status of the HW network link
+ * @hw: pointer to the HW struct
+ * @link_up: pointer to bool (true/false = linkup/linkdown)
+ *
+ * Variable link_up is true if link is up, false if link is down.
+ * The variable link_up is invalid if status is non zero. As a
+ * result of this call, link status reporting becomes enabled
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_get_link_status(struct ixgbe_hw *hw, bool *link_up)
+{
+ int err = 0;
+
+ if (!hw || !link_up)
+ return -EINVAL;
+
+ if (hw->link.get_link_info) {
+ err = ixgbe_update_link_info(hw);
+ if (err)
+ return err;
+ }
+
+ *link_up = hw->link.link_info.link_info & IXGBE_ACI_LINK_UP;
+
+ return err;
+}
+
+/**
+ * ixgbe_aci_get_link_info - get the link status
+ * @hw: pointer to the HW struct
+ * @ena_lse: enable/disable LinkStatusEvent reporting
+ * @link: pointer to link status structure - optional
+ *
+ * Get the current Link Status using ACI command (0x607).
+ * The current link can be optionally provided to update
+ * the status.
+ *
+ * Return: the link status of the adapter.
+ */
+int ixgbe_aci_get_link_info(struct ixgbe_hw *hw, bool ena_lse,
+ struct ixgbe_link_status *link)
+{
+ struct ixgbe_aci_cmd_get_link_status_data link_data = { 0 };
+ struct ixgbe_aci_cmd_get_link_status *resp;
+ struct ixgbe_link_status *li_old, *li;
+ struct ixgbe_fc_info *hw_fc_info;
+ enum ixgbe_media_type *hw_media_type;
+ struct ixgbe_aci_desc desc;
+ bool tx_pause, rx_pause;
+ u16 cmd_flags;
+ int err;
+
+ if (!hw)
+ return -EINVAL;
+
+ li_old = &hw->link.link_info_old;
+ hw_media_type = &hw->phy.media_type;
+ li = &hw->link.link_info;
+ hw_fc_info = &hw->fc;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_get_link_status);
+ cmd_flags = (ena_lse) ? IXGBE_ACI_LSE_ENA : IXGBE_ACI_LSE_DIS;
+ resp = &desc.params.get_link_status;
+ resp->cmd_flags = cmd_flags;
+ resp->lport_num = hw->bus.func;
+
+ err = ixgbe_aci_send_cmd(hw, &desc, &link_data, sizeof(link_data));
+
+ if (err)
+ return err;
+
+ /* Save off old link status information. */
+ *li_old = *li;
+
+ /* Update current link status information. */
+ li->link_speed = link_data.link_speed;
+ li->phy_type_low = link_data.phy_type_low;
+ li->phy_type_high = link_data.phy_type_high;
+ *hw_media_type = ixgbe_get_media_type_from_phy_type(hw);
+ li->link_info = link_data.link_info;
+ li->link_cfg_err = link_data.link_cfg_err;
+ li->an_info = link_data.an_info;
+ li->ext_info = link_data.ext_info;
+ li->max_frame_size = link_data.max_frame_size;
+ li->fec_info = link_data.cfg & IXGBE_ACI_FEC_MASK;
+ li->topo_media_conflict = link_data.topo_media_conflict;
+ li->pacing = link_data.cfg & (IXGBE_ACI_CFG_PACING_M |
+ IXGBE_ACI_CFG_PACING_TYPE_M);
+
+ /* Update fc info. */
+ tx_pause = !!(link_data.an_info & IXGBE_ACI_LINK_PAUSE_TX);
+ rx_pause = !!(link_data.an_info & IXGBE_ACI_LINK_PAUSE_RX);
+ if (tx_pause && rx_pause)
+ hw_fc_info->current_mode = ixgbe_fc_full;
+ else if (tx_pause)
+ hw_fc_info->current_mode = ixgbe_fc_tx_pause;
+ else if (rx_pause)
+ hw_fc_info->current_mode = ixgbe_fc_rx_pause;
+ else
+ hw_fc_info->current_mode = ixgbe_fc_none;
+
+ li->lse_ena = !!(resp->cmd_flags & IXGBE_ACI_LSE_IS_ENABLED);
+
+ /* Save link status information. */
+ if (link)
+ *link = *li;
+
+ /* Flag cleared so calling functions don't call AQ again. */
+ hw->link.get_link_info = false;
+
+ return 0;
+}
+
+/**
+ * ixgbe_aci_set_event_mask - set event mask
+ * @hw: pointer to the HW struct
+ * @port_num: port number of the physical function
+ * @mask: event mask to be set
+ *
+ * Set the event mask using ACI command (0x0613).
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_set_event_mask(struct ixgbe_hw *hw, u8 port_num, u16 mask)
+{
+ struct ixgbe_aci_cmd_set_event_mask *cmd;
+ struct ixgbe_aci_desc desc;
+
+ cmd = &desc.params.set_event_mask;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_set_event_mask);
+
+ cmd->lport_num = port_num;
+
+ cmd->event_mask = mask;
+ return ixgbe_aci_send_cmd(hw, &desc, NULL, 0);
+}
+
+/**
+ * ixgbe_configure_lse - enable/disable link status events
+ * @hw: pointer to the HW struct
+ * @activate: true for enable lse, false otherwise
+ * @mask: event mask to be set; a set bit means deactivation of the
+ * corresponding event
+ *
+ * Set the event mask and then enable or disable link status events
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_configure_lse(struct ixgbe_hw *hw, bool activate, u16 mask)
+{
+ int err;
+
+ err = ixgbe_aci_set_event_mask(hw, hw->bus.func, mask);
+ if (err)
+ return err;
+
+ /* Enabling link status events generation by fw */
+ err = ixgbe_aci_get_link_info(hw, activate, NULL);
+ if (err)
+ return err;
+
+ return 0;
+}
+
+/**
+ * ixgbe_get_media_type_e610 - Gets media type
+ * @hw: pointer to the HW struct
+ *
+ * In order to get the media type, the function gets PHY
+ * capabilities and later on use them to identify the PHY type
+ * checking phy_type_high and phy_type_low.
+ *
+ * Return: the type of media in form of ixgbe_media_type enum
+ * or ixgbe_media_type_unknown in case of an error.
+ */
+enum ixgbe_media_type ixgbe_get_media_type_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data pcaps;
+ int rc;
+
+ rc = ixgbe_update_link_info(hw);
+ if (rc)
+ return ixgbe_media_type_unknown;
+
+ /* If there is no link but PHY (dongle) is available SW should use
+ * Get PHY Caps admin command instead of Get Link Status, find most
+ * significant bit that is set in PHY types reported by the command
+ * and use it to discover media type.
+ */
+ if (!(hw->link.link_info.link_info & IXGBE_ACI_LINK_UP) &&
+ (hw->link.link_info.link_info & IXGBE_ACI_MEDIA_AVAILABLE)) {
+ int highest_bit;
+
+ /* Get PHY Capabilities */
+ rc = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_TOPO_CAP_MEDIA,
+ &pcaps);
+ if (rc)
+ return ixgbe_media_type_unknown;
+
+ highest_bit = fls64(pcaps.phy_type_high);
+ if (highest_bit) {
+ hw->link.link_info.phy_type_high =
+ BIT_ULL(highest_bit - 1);
+ hw->link.link_info.phy_type_low = 0;
+ } else {
+ highest_bit = fls64(pcaps.phy_type_low);
+ if (highest_bit)
+ hw->link.link_info.phy_type_low =
+ BIT_ULL(highest_bit - 1);
+ }
+
+ /* Based on search above try to discover media type */
+ hw->phy.media_type = ixgbe_get_media_type_from_phy_type(hw);
+ }
+
+ return hw->phy.media_type;
+}
+
+/**
+ * ixgbe_setup_link_e610 - Set up link
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait: true when waiting for completion is needed
+ *
+ * Set up the link with the specified speed.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_setup_link_e610(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+ bool autoneg_wait)
+{
+ /* Simply request FW to perform proper PHY setup */
+ return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait);
+}
+
+/**
+ * ixgbe_check_link_e610 - Determine link and speed status
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @link_up: true when link is up
+ * @link_up_wait_to_complete: bool used to wait for link up or not
+ *
+ * Determine if the link is up and the current link speed
+ * using ACI command (0x0607).
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_check_link_e610(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
+ bool *link_up, bool link_up_wait_to_complete)
+{
+ int err;
+ u32 i;
+
+ if (!speed || !link_up)
+ return -EINVAL;
+
+ /* Set get_link_info flag to ensure that fresh
+ * link information will be obtained from FW
+ * by sending Get Link Status admin command.
+ */
+ hw->link.get_link_info = true;
+
+ /* Update link information in adapter context. */
+ err = ixgbe_get_link_status(hw, link_up);
+ if (err)
+ return err;
+
+ /* Wait for link up if it was requested. */
+ if (!link_up_wait_to_complete && *link_up) {
+ for (i = 0; i < hw->mac.max_link_up_time; i++) {
+ msleep(100);
+ hw->link.get_link_info = true;
+ err = ixgbe_get_link_status(hw, link_up);
+ if (err)
+ return err;
+ if (*link_up)
+ break;
+ }
+ }
+
+ /* Use link information in adapter context updated by the call
+ * to ixgbe_get_link_status() to determine current link speed.
+ * Link speed information is valid only when link up was
+ * reported by FW.
+ */
+ if (*link_up) {
+ switch (hw->link.link_info.link_speed) {
+ case IXGBE_ACI_LINK_SPEED_10MB:
+ *speed = IXGBE_LINK_SPEED_10_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_100MB:
+ *speed = IXGBE_LINK_SPEED_100_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_1000MB:
+ *speed = IXGBE_LINK_SPEED_1GB_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_2500MB:
+ *speed = IXGBE_LINK_SPEED_2_5GB_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_5GB:
+ *speed = IXGBE_LINK_SPEED_5GB_FULL;
+ break;
+ case IXGBE_ACI_LINK_SPEED_10GB:
+ *speed = IXGBE_LINK_SPEED_10GB_FULL;
+ break;
+ default:
+ *speed = IXGBE_LINK_SPEED_UNKNOWN;
+ break;
+ }
+ } else {
+ *speed = IXGBE_LINK_SPEED_UNKNOWN;
+ }
+
+ return 0;
+}
+
+/**
+ * ixgbe_get_link_capabilities_e610 - Determine link capabilities
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @autoneg: true when autoneg or autotry is enabled
+ *
+ * Determine speed and AN parameters of a link.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_get_link_capabilities_e610(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg)
+{
+ if (!speed || !autoneg)
+ return -EINVAL;
+
+ *autoneg = true;
+ *speed = hw->phy.speeds_supported;
+
+ return 0;
+}
+
+/**
+ * ixgbe_cfg_phy_fc - Configure PHY Flow Control (FC) data based on FC mode
+ * @hw: pointer to hardware structure
+ * @cfg: PHY configuration data to set FC mode
+ * @req_mode: FC mode to configure
+ *
+ * Configures PHY Flow Control according to the provided configuration.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_cfg_phy_fc(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_set_phy_cfg_data *cfg,
+ enum ixgbe_fc_mode req_mode)
+{
+ u8 pause_mask = 0x0;
+
+ if (!cfg)
+ return -EINVAL;
+
+ switch (req_mode) {
+ case ixgbe_fc_full:
+ pause_mask |= IXGBE_ACI_PHY_EN_TX_LINK_PAUSE;
+ pause_mask |= IXGBE_ACI_PHY_EN_RX_LINK_PAUSE;
+ break;
+ case ixgbe_fc_rx_pause:
+ pause_mask |= IXGBE_ACI_PHY_EN_RX_LINK_PAUSE;
+ break;
+ case ixgbe_fc_tx_pause:
+ pause_mask |= IXGBE_ACI_PHY_EN_TX_LINK_PAUSE;
+ break;
+ default:
+ break;
+ }
+
+ /* Clear the old pause settings. */
+ cfg->caps &= ~(IXGBE_ACI_PHY_EN_TX_LINK_PAUSE |
+ IXGBE_ACI_PHY_EN_RX_LINK_PAUSE);
+
+ /* Set the new capabilities. */
+ cfg->caps |= pause_mask;
+
+ return 0;
+}
+
+/**
+ * ixgbe_setup_fc_e610 - Set up flow control
+ * @hw: pointer to hardware structure
+ *
+ * Set up flow control. This has to be done during init time.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_setup_fc_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data pcaps = { 0 };
+ struct ixgbe_aci_cmd_set_phy_cfg_data cfg = { 0 };
+ int err;
+
+ /* Get the current PHY config */
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_ACTIVE_CFG, &pcaps);
+ if (err)
+ return err;
+
+ ixgbe_copy_phy_caps_to_cfg(&pcaps, &cfg);
+
+ /* Configure the set PHY data */
+ err = ixgbe_cfg_phy_fc(hw, &cfg, hw->fc.requested_mode);
+ if (err)
+ return err;
+
+ /* If the capabilities have changed, then set the new config */
+ if (cfg.caps != pcaps.caps) {
+ cfg.caps |= IXGBE_ACI_PHY_ENA_AUTO_LINK_UPDT;
+
+ err = ixgbe_aci_set_phy_cfg(hw, &cfg);
+ if (err)
+ return err;
+ }
+
+ return err;
+}
+
+/**
+ * ixgbe_fc_autoneg_e610 - Configure flow control
+ * @hw: pointer to hardware structure
+ *
+ * Configure Flow Control.
+ */
+void ixgbe_fc_autoneg_e610(struct ixgbe_hw *hw)
+{
+ int err;
+
+ /* Get current link err.
+ * Current FC mode will be stored in the hw context.
+ */
+ err = ixgbe_aci_get_link_info(hw, false, NULL);
+ if (err)
+ goto out;
+
+ /* Check if the link is up */
+ if (!(hw->link.link_info.link_info & IXGBE_ACI_LINK_UP)) {
+ err = -EIO;
+ goto out;
+ }
+
+ /* Check if auto-negotiation has completed */
+ if (!(hw->link.link_info.an_info & IXGBE_ACI_AN_COMPLETED)) {
+ err = -EIO;
+ goto out;
+ }
+
+out:
+ if (!err) {
+ hw->fc.fc_was_autonegged = true;
+ } else {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ }
+}
+
+/**
+ * ixgbe_disable_rx_e610 - Disable RX unit
+ * @hw: pointer to hardware structure
+ *
+ * Disable RX DMA unit on E610 with use of ACI command (0x000C).
+ *
+ * Return: the exit code of the operation.
+ */
+void ixgbe_disable_rx_e610(struct ixgbe_hw *hw)
+{
+ u32 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
+
+ if (rxctrl & IXGBE_RXCTRL_RXEN) {
+ u32 pfdtxgswc;
+ int err;
+
+ pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
+ if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) {
+ pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN;
+ IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
+ hw->mac.set_lben = true;
+ } else {
+ hw->mac.set_lben = false;
+ }
+
+ err = ixgbe_aci_disable_rxen(hw);
+
+ /* If we fail - disable RX using register write */
+ if (err) {
+ rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
+ if (rxctrl & IXGBE_RXCTRL_RXEN) {
+ rxctrl &= ~IXGBE_RXCTRL_RXEN;
+ IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl);
+ }
+ }
+ }
+}
+
+/**
+ * ixgbe_init_phy_ops_e610 - PHY specific init
+ * @hw: pointer to hardware structure
+ *
+ * Initialize any function pointers that were not able to be
+ * set during init_shared_code because the PHY type was not known.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_init_phy_ops_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ struct ixgbe_phy_info *phy = &hw->phy;
+ int ret_val;
+
+ if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper)
+ phy->ops.set_phy_power = ixgbe_set_phy_power_e610;
+ else
+ phy->ops.set_phy_power = NULL;
+
+ /* Identify the PHY */
+ ret_val = phy->ops.identify(hw);
+ if (ret_val)
+ return ret_val;
+
+ return ret_val;
+}
+
+/**
+ * ixgbe_identify_phy_e610 - Identify PHY
+ * @hw: pointer to hardware structure
+ *
+ * Determine PHY type, supported speeds and PHY ID.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_identify_phy_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data pcaps;
+ int err;
+
+ /* Set PHY type */
+ hw->phy.type = ixgbe_phy_fw;
+
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_TOPO_CAP_MEDIA, &pcaps);
+ if (err)
+ return err;
+
+ if (!(pcaps.module_compliance_enforcement &
+ IXGBE_ACI_MOD_ENFORCE_STRICT_MODE)) {
+ /* Handle lenient mode */
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_TOPO_CAP_NO_MEDIA,
+ &pcaps);
+ if (err)
+ return err;
+ }
+
+ /* Determine supported speeds */
+ hw->phy.speeds_supported = IXGBE_LINK_SPEED_UNKNOWN;
+
+ if (pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_10BASE_T ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_10M_SGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_10_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_100BASE_TX ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_100M_SGMII ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_100M_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_100_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1000BASE_T ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1000BASE_SX ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1000BASE_LX ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1000BASE_KX ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_1G_SGMII ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_1G_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_1GB_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_2500BASE_T ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_2500BASE_X ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_2500BASE_KX ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_2500M_SGMII ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_2500M_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_2_5GB_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_5GBASE_T ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_5GBASE_KR ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_5G_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_5GB_FULL;
+ if (pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10GBASE_T ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10G_SFI_DA ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10GBASE_SR ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10GBASE_LR ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10GBASE_KR_CR1 ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10G_SFI_AOC_ACC ||
+ pcaps.phy_type_low & IXGBE_PHY_TYPE_LOW_10G_SFI_C2C ||
+ pcaps.phy_type_high & IXGBE_PHY_TYPE_HIGH_10G_USXGMII)
+ hw->phy.speeds_supported |= IXGBE_LINK_SPEED_10GB_FULL;
+
+ /* Initialize autoneg speeds */
+ if (!hw->phy.autoneg_advertised)
+ hw->phy.autoneg_advertised = hw->phy.speeds_supported;
+
+ /* Set PHY ID */
+ memcpy(&hw->phy.id, pcaps.phy_id_oui, sizeof(u32));
+
+ hw->phy.eee_speeds_supported = IXGBE_LINK_SPEED_10_FULL |
+ IXGBE_LINK_SPEED_100_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ hw->phy.eee_speeds_advertised = hw->phy.eee_speeds_supported;
+
+ return 0;
+}
+
+/**
+ * ixgbe_identify_module_e610 - Identify SFP module type
+ * @hw: pointer to hardware structure
+ *
+ * Identify the SFP module type.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_identify_module_e610(struct ixgbe_hw *hw)
+{
+ bool media_available;
+ u8 module_type;
+ int err;
+
+ err = ixgbe_update_link_info(hw);
+ if (err)
+ goto err;
+
+ media_available =
+ (hw->link.link_info.link_info & IXGBE_ACI_MEDIA_AVAILABLE);
+
+ if (media_available) {
+ hw->phy.sfp_type = ixgbe_sfp_type_unknown;
+
+ /* Get module type from hw context updated by
+ * ixgbe_update_link_info()
+ */
+ module_type = hw->link.link_info.module_type[IXGBE_ACI_MOD_TYPE_IDENT];
+
+ if ((module_type & IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_PASSIVE) ||
+ (module_type & IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_ACTIVE)) {
+ hw->phy.sfp_type = ixgbe_sfp_type_da_cu;
+ } else if (module_type & IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_SR) {
+ hw->phy.sfp_type = ixgbe_sfp_type_sr;
+ } else if ((module_type & IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_LR) ||
+ (module_type & IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_LRM)) {
+ hw->phy.sfp_type = ixgbe_sfp_type_lr;
+ }
+ err = 0;
+ } else {
+ hw->phy.sfp_type = ixgbe_sfp_type_not_present;
+ err = -ENOENT;
+ }
+err:
+ return err;
+}
+
+/**
+ * ixgbe_setup_phy_link_e610 - Sets up firmware-controlled PHYs
+ * @hw: pointer to hardware structure
+ *
+ * Set the parameters for the firmware-controlled PHYs.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_setup_phy_link_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data pcaps;
+ struct ixgbe_aci_cmd_set_phy_cfg_data pcfg;
+ int err;
+
+ err = ixgbe_aci_get_link_info(hw, false, NULL);
+ if (err)
+ goto err;
+
+ /* Set PHY Configuration only if media is available */
+ if (!(hw->link.link_info.link_info & IXGBE_ACI_MEDIA_AVAILABLE)) {
+ err = ixgbe_aci_set_link_restart_an(hw, false);
+ if (err)
+ goto err;
+
+ return 0;
+ }
+
+ err = ixgbe_aci_get_phy_caps(hw, false, IXGBE_ACI_REPORT_DFLT_CFG,
+ &pcaps);
+ if (err)
+ goto err;
+
+ ixgbe_copy_phy_caps_to_cfg(&pcaps, &pcfg);
+
+ pcfg.caps |= IXGBE_ACI_PHY_ENA_LINK;
+ pcfg.caps |= IXGBE_ACI_PHY_ENA_AUTO_LINK_UPDT;
+
+ /* Set default PHY types for a given speed */
+ pcfg.phy_type_low = 0;
+ pcfg.phy_type_high = 0;
+
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10_FULL) {
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_10BASE_T;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_10M_SGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_100BASE_TX;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_100M_SGMII;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_100M_USXGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1000BASE_T;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1000BASE_SX;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1000BASE_LX;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1000BASE_KX;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_1G_SGMII;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_1G_USXGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_2_5GB_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_2500BASE_T;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_2500BASE_X;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_2500BASE_KX;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_2500M_SGMII;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_2500M_USXGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_5GB_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_5GBASE_T;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_5GBASE_KR;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_5G_USXGMII;
+ }
+ if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL) {
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10GBASE_T;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10G_SFI_DA;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10GBASE_SR;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10GBASE_LR;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10GBASE_KR_CR1;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10G_SFI_AOC_ACC;
+ pcfg.phy_type_low |= IXGBE_PHY_TYPE_LOW_10G_SFI_C2C;
+ pcfg.phy_type_high |= IXGBE_PHY_TYPE_HIGH_10G_USXGMII;
+ }
+
+ /* Mask the set values to avoid requesting unsupported link types */
+ pcfg.phy_type_low &= pcaps.phy_type_low;
+ pcfg.phy_type_high &= pcaps.phy_type_high;
+
+ err = ixgbe_aci_set_phy_cfg(hw, &pcfg);
+ if (err)
+ goto err;
+
+ /* Request link restart - without putting it down */
+ err = ixgbe_aci_set_link_restart_an(hw, true);
+ if (err)
+ goto err;
+
+err:
+ return err;
+}
+
+/**
+ * ixgbe_set_phy_power_e610 - Control power for copper PHY
+ * @hw: pointer to hardware structure
+ * @on: true for on, false for off
+ *
+ * Set the power on/off of the PHY
+ * by getting its capabilities and setting the appropriate
+ * configuration parameters.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_set_phy_power_e610(struct ixgbe_hw *hw, bool on)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data phy_caps = { 0 };
+ struct ixgbe_aci_cmd_set_phy_cfg_data phy_cfg = { 0 };
+ int err;
+
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_ACTIVE_CFG,
+ &phy_caps);
+ if (err)
+ return err;
+
+ ixgbe_copy_phy_caps_to_cfg(&phy_caps, &phy_cfg);
+
+ if (on)
+ phy_cfg.caps &= ~IXGBE_ACI_PHY_ENA_LOW_POWER;
+ else
+ phy_cfg.caps |= IXGBE_ACI_PHY_ENA_LOW_POWER;
+
+ phy_cfg.caps |= IXGBE_ACI_PHY_ENA_LINK;
+ phy_cfg.caps |= IXGBE_ACI_PHY_ENA_AUTO_LINK_UPDT;
+
+ err = ixgbe_aci_set_phy_cfg(hw, &phy_cfg);
+
+ return err;
+}
+
+/**
+ * ixgbe_enter_lplu_e610 - Transition to low power states
+ * @hw: pointer to hardware structure
+ *
+ * Configures Low Power Link Up on transition to low power states
+ * (from D0 to non-D0). Link is required to enter LPLU so avoid resetting the
+ * X557 PHY immediately prior to entering LPLU.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_enter_lplu_e610(struct ixgbe_hw *hw)
+{
+ struct ixgbe_aci_cmd_get_phy_caps_data phy_caps = { 0 };
+ struct ixgbe_aci_cmd_set_phy_cfg_data phy_cfg = { 0 };
+ int err;
+
+ err = ixgbe_aci_get_phy_caps(hw, false,
+ IXGBE_ACI_REPORT_ACTIVE_CFG,
+ &phy_caps);
+ if (err)
+ return err;
+
+ ixgbe_copy_phy_caps_to_cfg(&phy_caps, &phy_cfg);
+
+ phy_cfg.low_power_ctrl_an |= IXGBE_ACI_PHY_EN_D3COLD_LOW_POWER_AUTONEG;
+
+ err = ixgbe_aci_set_phy_cfg(hw, &phy_cfg);
+
+ return err;
+}
+
+/**
+ * ixgbe_aci_get_netlist_node - get a node handle
+ * @hw: pointer to the hw struct
+ * @cmd: get_link_topo AQ structure
+ * @node_part_number: output node part number if node found
+ * @node_handle: output node handle parameter if node found
+ *
+ * Get the netlist node and assigns it to
+ * the provided handle using ACI command (0x06E0).
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_get_netlist_node(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_get_link_topo *cmd,
+ u8 *node_part_number, u16 *node_handle)
+{
+ struct ixgbe_aci_desc desc;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_get_link_topo);
+ desc.params.get_link_topo = *cmd;
+
+ if (ixgbe_aci_send_cmd(hw, &desc, NULL, 0))
+ return -EOPNOTSUPP;
+
+ if (node_handle)
+ *node_handle = desc.params.get_link_topo.addr.handle;
+ if (node_part_number)
+ *node_part_number = desc.params.get_link_topo.node_part_num;
+
+ return 0;
+}
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_e610.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_e610.h
index b5257fc..9be412a 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_e610.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_e610.h
@@ -26,5 +26,37 @@ int ixgbe_aci_get_phy_caps(struct ixgbe_hw *hw, bool qual_mods, u8 report_mode,
struct ixgbe_aci_cmd_get_phy_caps_data *pcaps);
void ixgbe_copy_phy_caps_to_cfg(struct ixgbe_aci_cmd_get_phy_caps_data *caps,
struct ixgbe_aci_cmd_set_phy_cfg_data *cfg);
+int ixgbe_aci_set_phy_cfg(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_set_phy_cfg_data *cfg);
+int ixgbe_aci_set_link_restart_an(struct ixgbe_hw *hw, bool ena_link);
+int ixgbe_update_link_info(struct ixgbe_hw *hw);
+int ixgbe_get_link_status(struct ixgbe_hw *hw, bool *link_up);
+int ixgbe_aci_get_link_info(struct ixgbe_hw *hw, bool ena_lse,
+ struct ixgbe_link_status *link);
+int ixgbe_aci_set_event_mask(struct ixgbe_hw *hw, u8 port_num, u16 mask);
+int ixgbe_configure_lse(struct ixgbe_hw *hw, bool activate, u16 mask);
+enum ixgbe_media_type ixgbe_get_media_type_e610(struct ixgbe_hw *hw);
+int ixgbe_setup_link_e610(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+ bool autoneg_wait);
+int ixgbe_check_link_e610(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
+ bool *link_up, bool link_up_wait_to_complete);
+int ixgbe_get_link_capabilities_e610(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg);
+int ixgbe_cfg_phy_fc(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_set_phy_cfg_data *cfg,
+ enum ixgbe_fc_mode req_mode);
+int ixgbe_setup_fc_e610(struct ixgbe_hw *hw);
+void ixgbe_fc_autoneg_e610(struct ixgbe_hw *hw);
+void ixgbe_disable_rx_e610(struct ixgbe_hw *hw);
+int ixgbe_init_phy_ops_e610(struct ixgbe_hw *hw);
+int ixgbe_identify_phy_e610(struct ixgbe_hw *hw);
+int ixgbe_identify_module_e610(struct ixgbe_hw *hw);
+int ixgbe_setup_phy_link_e610(struct ixgbe_hw *hw);
+int ixgbe_set_phy_power_e610(struct ixgbe_hw *hw, bool on);
+int ixgbe_enter_lplu_e610(struct ixgbe_hw *hw);
+int ixgbe_aci_get_netlist_node(struct ixgbe_hw *hw,
+ struct ixgbe_aci_cmd_get_link_topo *cmd,
+ u8 *node_part_number, u16 *node_handle);
#endif /* _IXGBE_E610_H_ */
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type_e610.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type_e610.h
index ffd1707..1e6d752 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type_e610.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type_e610.h
@@ -647,6 +647,7 @@ struct ixgbe_aci_cmd_link_topo_params {
#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_CLK_MUX 10
#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_GPS 11
#define IXGBE_ACI_LINK_TOPO_NODE_CTX_S 4
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_M GENMASK(7, 4)
#define IXGBE_ACI_LINK_TOPO_NODE_CTX_GLOBAL 0
#define IXGBE_ACI_LINK_TOPO_NODE_CTX_BOARD 1
#define IXGBE_ACI_LINK_TOPO_NODE_CTX_PORT 2
--
2.31.1
Powered by blists - more mailing lists