lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <87o774u807.fsf@intel.com>
Date: Wed, 10 Jul 2024 16:44:56 -0700
From: Vinicius Costa Gomes <vinicius.gomes@...el.com>
To: Faizal Rahim <faizal.abdul.rahim@...ux.intel.com>, "David S . Miller"
 <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>, Jakub Kicinski
 <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>, Jesse Brandeburg
 <jesse.brandeburg@...el.com>, Tony
 Nguyen <anthony.l.nguyen@...el.com>, Simon Horman <horms@...nel.org>,
 Richard Cochran <richardcochran@...il.com>, Paul Menzel
 <pmenzel@...gen.mpg.de>, Sasha Neftin <sasha.neftin@...el.com>
Cc: intel-wired-lan@...ts.osuosl.org, netdev@...r.kernel.org,
 linux-kernel@...r.kernel.org, stable@...r.kernel.org, Faizal Rahim
 <faizal.abdul.rahim@...ux.intel.com>
Subject: Re: [PATCH iwl-net v2 2/3] igc: Fix reset adapter logics when tx
 mode change

Faizal Rahim <faizal.abdul.rahim@...ux.intel.com> writes:

> Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
> remaining issues with the reset adapter logic in igc_tsn_offload_apply()
> have been observed:
>
> 1. The reset adapter logics for i225 and i226 differ, although they should
>    be the same according to the guidelines in I225/6 HW Design Section
>    7.5.2.1 on software initialization during tx mode changes.
> 2. The i225 resets adapter every time, even though tx mode doesn't change.
>    This occurs solely based on the condition  igc_is_device_id_i225() when
>    calling schedule_work().
> 3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only
>    resets adapter for legacy->tsn tx mode transitions.
> 4. qbv_count introduced in the patch is actually not needed; in this
>    context, a non-zero value of qbv_count is used to indicate if tx mode
>    was unconditionally set to tsn in igc_tsn_enable_offload(). This could
>    be replaced by checking the existing register
>    IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit.
>
> This patch resolves all issues and enters schedule_work() to reset the
> adapter only when changing tx mode. It also removes reliance on qbv_count.
>
> qbv_count field will be removed in a future patch.
>
> Test ran:
>
> 1. Verify reset adapter behaviour in i225/6:
>    a) Enrol a new GCL
>       Reset adapter observed (tx mode change legacy->tsn)
>    b) Enrol a new GCL without deleting qdisc
>       No reset adapter observed (tx mode remain tsn->tsn)
>    c) Delete qdisc
>       Reset adapter observed (tx mode change tsn->legacy)
>
> 2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed"
>    to confirm it remains resolved.
>
> Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed")
> Signed-off-by: Faizal Rahim <faizal.abdul.rahim@...ux.intel.com>
> Reviewed-by: Simon Horman <horms@...nel.org>
> ---

There were a quite a few bugs, some of them my fault, on this part of
the code, changing between the modes in the hardware.

So I would like some confirmation that ETF offloading/LaunchTime was
also tested with this change. Just to be sure.

But code-wise, looks good:

Acked-by: Vinicius Costa Gomes <vinicius.gomes@...el.com>


Cheers,
-- 
Vinicius

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ