| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <5bcdb73d995bedc805053a7683abfce4ba02c5bb.1722253726.git.siyanteng@loongson.cn>
Date: Mon, 29 Jul 2024 20:24:32 +0800
From: Yanteng Si <siyanteng@...ngson.cn>
To: andrew@...n.ch,
hkallweit1@...il.com,
peppe.cavallaro@...com,
alexandre.torgue@...s.st.com,
joabreu@...opsys.com,
fancer.lancer@...il.com,
diasyzhang@...cent.com
Cc: Yanteng Si <siyanteng@...ngson.cn>,
Jose.Abreu@...opsys.com,
chenhuacai@...nel.org,
linux@...linux.org.uk,
guyinggang@...ngson.cn,
netdev@...r.kernel.org,
chris.chenfeiyang@...il.com,
si.yanteng@...ux.dev,
Huacai Chen <chenhuacai@...ngson.cn>
Subject: [PATCH net-next v15 13/14] net: stmmac: dwmac-loongson: Add Loongson GNET support
The new generation Loongson LS2K2000 SoC and LS7A2000 chipset are
equipped with the network controllers called Loongson GNET. It's the
single and multi DMA-channels Loongson GMAC but with a PHY attached.
Here is the summary of the DW GMAC features the controller has:
DW GMAC IP-core: v3.73a
Speeds: 10/100/1000Mbps
Duplex: Full (both versions), Half (LS2K2000 GNET only)
DMA-descriptors type: enhanced
L3/L4 filters availability: Y
VLAN hash table filter: Y
PHY-interface: GMII (PHY is integrated into the chips)
Remote Wake-up support: Y
Mac Management Counters (MMC): Y
Number of additional MAC addresses: 5
MAC Hash-based filter: Y
Hash Table Size: 256
AV feature: Y (LS2K2000 GNET only)
DMA channels: 8 (LS2K2000 GNET), 1 (LS7A2000 GNET)
Let's update the Loongson DWMAC driver to supporting the new Loongson
GNET controller. The change is mainly trivial: the driver shall be
bound to the PCIe device with DID 0x7a13, and the device-specific
setup() method shall be called for it. The only peculiarity concerns
the integrated PHY speed change procedure. The PHY has a weird problem
with switching from the low speeds to 1000Mbps mode. The speedup
procedure requires the PHY-link re-negotiation. So the suggested
change provide the device-specific fix_mac_speed() method to overcome
the problem.
Signed-off-by: Feiyang Chen <chenfeiyang@...ngson.cn>
Signed-off-by: Yinggang Gu <guyinggang@...ngson.cn>
Acked-by: Huacai Chen <chenhuacai@...ngson.cn>
Signed-off-by: Yanteng Si <siyanteng@...ngson.cn>
---
.../ethernet/stmicro/stmmac/dwmac-loongson.c | 77 ++++++++++++++++++-
1 file changed, 74 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
index eea6a22b10ca..18fc3dd983cb 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
@@ -65,11 +65,13 @@
DMA_STATUS_MSK_COMMON_LOONGSON)
#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03
+#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13
#define DWMAC_CORE_LS_MULTICHAN 0x10 /* Loongson custom ID */
#define CHANNEL_NUM 8
struct loongson_data {
u32 loongson_id;
+ struct device *dev;
};
struct stmmac_pci_info {
@@ -147,6 +149,60 @@ static struct stmmac_pci_info loongson_gmac_pci_info = {
.setup = loongson_gmac_data,
};
+static void loongson_gnet_fix_speed(void *priv, unsigned int speed,
+ unsigned int mode)
+{
+ struct loongson_data *ld = (struct loongson_data *)priv;
+ struct net_device *ndev = dev_get_drvdata(ld->dev);
+ struct stmmac_priv *ptr = netdev_priv(ndev);
+
+ /* The integrated PHY has a weird problem with switching from the low
+ * speeds to 1000Mbps mode. The speedup procedure requires the PHY-link
+ * re-negotiation.
+ */
+ if (speed == SPEED_1000) {
+ if (readl(ptr->ioaddr + MAC_CTRL_REG) &
+ GMAC_CONTROL_PS)
+ /* Word around hardware bug, restart autoneg */
+ phy_restart_aneg(ndev->phydev);
+ }
+}
+
+static int loongson_gnet_data(struct pci_dev *pdev,
+ struct plat_stmmacenet_data *plat)
+{
+ struct loongson_data *ld;
+ int i;
+
+ ld = plat->bsp_priv;
+
+ loongson_default_data(pdev, plat);
+
+ if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN) {
+ plat->rx_queues_to_use = CHANNEL_NUM;
+ plat->tx_queues_to_use = CHANNEL_NUM;
+
+ /* Only channel 0 supports checksum,
+ * so turn off checksum to enable multiple channels.
+ */
+ for (i = 1; i < CHANNEL_NUM; i++)
+ plat->tx_queues_cfg[i].coe_unsupported = 1;
+ } else {
+ plat->tx_queues_to_use = 1;
+ plat->rx_queues_to_use = 1;
+ }
+
+ plat->phy_interface = PHY_INTERFACE_MODE_GMII;
+ plat->mdio_bus_data->phy_mask = ~(u32)BIT(2);
+ plat->fix_mac_speed = loongson_gnet_fix_speed;
+
+ return 0;
+}
+
+static struct stmmac_pci_info loongson_gnet_pci_info = {
+ .setup = loongson_gnet_data,
+};
+
static void loongson_dwmac_dma_init_channel(struct stmmac_priv *priv,
void __iomem *ioaddr,
struct stmmac_dma_cfg *dma_cfg,
@@ -279,8 +335,10 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv)
struct mac_device_info *mac;
struct stmmac_dma_ops *dma;
struct loongson_data *ld;
+ struct pci_dev *pdev;
ld = priv->plat->bsp_priv;
+ pdev = to_pci_dev(priv->device);
mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL);
if (!mac)
@@ -290,7 +348,7 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv)
if (!dma)
return NULL;
- /* The Loongson GMAC devices are based on the DW GMAC
+ /* The Loongson GMAC and GNET devices are based on the DW GMAC
* v3.50a and v3.73a IP-cores. But the HW designers have changed the
* GMAC_VERSION.SNPSVER field to the custom 0x10 value on the
* network controllers with the multi-channels feature
@@ -319,8 +377,19 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv)
if (mac->multicast_filter_bins)
mac->mcast_bits_log2 = ilog2(mac->multicast_filter_bins);
- /* Loongson GMAC doesn't support the flow control. */
- mac->link.caps = MAC_10 | MAC_100 | MAC_1000;
+ /* Loongson GMAC doesn't support the flow control. LS2K2000
+ * GNET doesn't support the half-duplex link mode.
+ */
+ if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC) {
+ mac->link.caps = MAC_10 | MAC_100 | MAC_1000;
+ } else {
+ if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN)
+ mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+ MAC_10 | MAC_100 | MAC_1000;
+ else
+ mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+ MAC_10FD | MAC_100FD | MAC_1000FD;
+ }
mac->link.duplex = GMAC_CONTROL_DM;
mac->link.speed10 = GMAC_CONTROL_PS;
@@ -495,6 +564,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
plat->bsp_priv = ld;
plat->setup = loongson_dwmac_setup;
+ ld->dev = &pdev->dev;
ld->loongson_id = readl(res.addr + GMAC_VERSION) & 0xff;
info = (struct stmmac_pci_info *)id->driver_data;
@@ -599,6 +669,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend,
static const struct pci_device_id loongson_dwmac_id_table[] = {
{ PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) },
+ { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) },
{}
};
MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);
--
2.31.4
Powered by blists - more mailing lists