| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20240731103403.407818-4-vtpieter@gmail.com>
Date: Wed, 31 Jul 2024 12:34:01 +0200
From: vtpieter@...il.com
To: devicetree@...r.kernel.org,
woojung.huh@...rochip.com,
UNGLinuxDriver@...rochip.com,
netdev@...r.kernel.org
Cc: o.rempel@...gutronix.de,
Pieter Van Trappen <pieter.van.trappen@...n.ch>
Subject: [PATCH net-next v2 3/5] net: dsa: microchip: generalize KSZ9477 WoL functions at ksz_common
From: Pieter Van Trappen <pieter.van.trappen@...n.ch>
Generalize KSZ9477 WoL functions at ksz_common. Move dedicated registers
and generic masks to existing structures & defines for that purpose.
Introduction of PME (port) read/write helper functions, which happen
to be the generic read/write for KSZ9477 but not for the incoming
KSZ87xx patch.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@...n.ch>
---
drivers/net/dsa/microchip/ksz9477.c | 14 +--
drivers/net/dsa/microchip/ksz9477.h | 5 --
drivers/net/dsa/microchip/ksz9477_reg.h | 12 ---
drivers/net/dsa/microchip/ksz_common.c | 109 ++++++++++++------------
drivers/net/dsa/microchip/ksz_common.h | 27 ++++--
5 files changed, 86 insertions(+), 81 deletions(-)
diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
index 071d953a17e9..a454a2e14a6b 100644
--- a/drivers/net/dsa/microchip/ksz9477.c
+++ b/drivers/net/dsa/microchip/ksz9477.c
@@ -1007,6 +1007,7 @@ void ksz9477_port_queue_split(struct ksz_device *dev, int port)
void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
{
+ const u16 *regs = dev->info->regs;
struct dsa_switch *ds = dev->ds;
u16 data16;
u8 member;
@@ -1051,12 +1052,12 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
ksz9477_port_acl_init(dev, port);
/* clear pending wake flags */
- ksz9477_handle_wake_reason(dev, port);
+ ksz_handle_wake_reason(dev, port);
/* Disable all WoL options by default. Otherwise
* ksz_switch_macaddr_get/put logic will not work properly.
*/
- ksz_pwrite8(dev, port, REG_PORT_PME_CTRL, 0);
+ ksz_pwrite8(dev, port, regs[REG_PORT_PME_CTRL], 0);
}
void ksz9477_config_cpu_port(struct dsa_switch *ds)
@@ -1153,6 +1154,7 @@ int ksz9477_enable_stp_addr(struct ksz_device *dev)
int ksz9477_setup(struct dsa_switch *ds)
{
struct ksz_device *dev = ds->priv;
+ const u16 *regs = dev->info->regs;
int ret = 0;
ds->mtu_enforcement_ingress = true;
@@ -1183,11 +1185,11 @@ int ksz9477_setup(struct dsa_switch *ds)
/* enable global MIB counter freeze function */
ksz_cfg(dev, REG_SW_MAC_CTRL_6, SW_MIB_COUNTER_FREEZE, true);
- /* Make sure PME (WoL) is not enabled. If requested, it will be
- * enabled by ksz9477_wol_pre_shutdown(). Otherwise, some PMICs do not
- * like PME events changes before shutdown.
+ /* Make sure PME (WoL) is not enabled. If requested, it will
+ * be enabled by ksz_wol_pre_shutdown(). Otherwise, some PMICs
+ * do not like PME events changes before shutdown.
*/
- ksz_write8(dev, REG_SW_PME_CTRL, 0);
+ ksz_write8(dev, regs[REG_SW_PME_CTRL], 0);
return 0;
}
diff --git a/drivers/net/dsa/microchip/ksz9477.h b/drivers/net/dsa/microchip/ksz9477.h
index 239a281da10b..d2166b0d881e 100644
--- a/drivers/net/dsa/microchip/ksz9477.h
+++ b/drivers/net/dsa/microchip/ksz9477.h
@@ -60,11 +60,6 @@ void ksz9477_switch_exit(struct ksz_device *dev);
void ksz9477_port_queue_split(struct ksz_device *dev, int port);
void ksz9477_hsr_join(struct dsa_switch *ds, int port, struct net_device *hsr);
void ksz9477_hsr_leave(struct dsa_switch *ds, int port, struct net_device *hsr);
-void ksz9477_get_wol(struct ksz_device *dev, int port,
- struct ethtool_wolinfo *wol);
-int ksz9477_set_wol(struct ksz_device *dev, int port,
- struct ethtool_wolinfo *wol);
-void ksz9477_wol_pre_shutdown(struct ksz_device *dev, bool *wol_enabled);
int ksz9477_port_acl_init(struct ksz_device *dev, int port);
void ksz9477_port_acl_free(struct ksz_device *dev, int port);
diff --git a/drivers/net/dsa/microchip/ksz9477_reg.h b/drivers/net/dsa/microchip/ksz9477_reg.h
index d5354c600ea1..04235c22bf40 100644
--- a/drivers/net/dsa/microchip/ksz9477_reg.h
+++ b/drivers/net/dsa/microchip/ksz9477_reg.h
@@ -38,11 +38,6 @@
#define SWITCH_REVISION_S 4
#define SWITCH_RESET 0x01
-#define REG_SW_PME_CTRL 0x0006
-
-#define PME_ENABLE BIT(1)
-#define PME_POLARITY BIT(0)
-
#define REG_GLOBAL_OPTIONS 0x000F
#define SW_GIGABIT_ABLE BIT(6)
@@ -807,13 +802,6 @@
#define REG_PORT_AVB_SR_1_TYPE 0x0008
#define REG_PORT_AVB_SR_2_TYPE 0x000A
-#define REG_PORT_PME_STATUS 0x0013
-#define REG_PORT_PME_CTRL 0x0017
-
-#define PME_WOL_MAGICPKT BIT(2)
-#define PME_WOL_LINKUP BIT(1)
-#define PME_WOL_ENERGY BIT(0)
-
#define REG_PORT_INT_STATUS 0x001B
#define REG_PORT_INT_MASK 0x001F
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 41f89e2c6b2d..e5358da8cbeb 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -348,9 +348,9 @@ static const struct ksz_dev_ops ksz9477_dev_ops = {
.mdb_add = ksz9477_mdb_add,
.mdb_del = ksz9477_mdb_del,
.change_mtu = ksz9477_change_mtu,
- .get_wol = ksz9477_get_wol,
- .set_wol = ksz9477_set_wol,
- .wol_pre_shutdown = ksz9477_wol_pre_shutdown,
+ .pme_write8 = ksz_write8,
+ .pme_pread8 = ksz_pread8,
+ .pme_pwrite8 = ksz_pwrite8,
.config_cpu_port = ksz9477_config_cpu_port,
.tc_cbs_set_cinc = ksz9477_tc_cbs_set_cinc,
.enable_stp_addr = ksz9477_enable_stp_addr,
@@ -539,6 +539,9 @@ static const u16 ksz9477_regs[] = {
[S_MULTICAST_CTRL] = 0x0331,
[P_XMII_CTRL_0] = 0x0300,
[P_XMII_CTRL_1] = 0x0301,
+ [REG_SW_PME_CTRL] = 0x0006,
+ [REG_PORT_PME_STATUS] = 0x0013,
+ [REG_PORT_PME_CTRL] = 0x0017,
};
static const u32 ksz9477_masks[] = {
@@ -3731,31 +3734,27 @@ static int ksz_setup_tc(struct dsa_switch *ds, int port,
}
}
-static void ksz_get_wol(struct dsa_switch *ds, int port,
- struct ethtool_wolinfo *wol)
-{
- struct ksz_device *dev = ds->priv;
-
- if (dev->dev_ops->get_wol)
- dev->dev_ops->get_wol(dev, port, wol);
-}
-
/**
- * ksz9477_get_wol - Get Wake-on-LAN settings for a specified port.
- * @dev: The device structure.
+ * ksz_get_wol - Get Wake-on-LAN settings for a specified port.
+ * @ds: The dsa_switch structure.
* @port: The port number.
* @wol: Pointer to ethtool Wake-on-LAN settings structure.
*
- * This function checks the PME Pin Control Register to see if PME Pin Output
- * Enable is set, indicating PME is enabled. If enabled, it sets the supported
- * and active WoL flags.
+ * This function checks the device PME wakeup_source flag and chip_id.
+ * If enabled and supported, it sets the supported and active WoL
+ * flags.
*/
-void ksz9477_get_wol(struct ksz_device *dev, int port,
- struct ethtool_wolinfo *wol)
+static void ksz_get_wol(struct dsa_switch *ds, int port,
+ struct ethtool_wolinfo *wol)
{
+ struct ksz_device *dev = ds->priv;
+ const u16 *regs = dev->info->regs;
u8 pme_ctrl;
int ret;
+ if (!is_ksz9477(dev))
+ return;
+
if (!dev->wakeup_source)
return;
@@ -3768,7 +3767,8 @@ void ksz9477_get_wol(struct ksz_device *dev, int port,
if (ksz_is_port_mac_global_usable(dev->ds, port))
wol->supported |= WAKE_MAGIC;
- ret = ksz_pread8(dev, port, REG_PORT_PME_CTRL, &pme_ctrl);
+ ret = dev->dev_ops->pme_pread8(dev, port, regs[REG_PORT_PME_CTRL],
+ &pme_ctrl);
if (ret)
return;
@@ -3778,35 +3778,26 @@ void ksz9477_get_wol(struct ksz_device *dev, int port,
wol->wolopts |= WAKE_PHY;
}
-static int ksz_set_wol(struct dsa_switch *ds, int port,
- struct ethtool_wolinfo *wol)
-{
- struct ksz_device *dev = ds->priv;
-
- if (dev->dev_ops->set_wol)
- return dev->dev_ops->set_wol(dev, port, wol);
-
- return -EOPNOTSUPP;
-}
-
/**
- * ksz9477_set_wol - Set Wake-on-LAN settings for a specified port.
- * @dev: The device structure.
+ * ksz_set_wol - Set Wake-on-LAN settings for a specified port.
+ * @ds: The dsa_switch structure.
* @port: The port number.
* @wol: Pointer to ethtool Wake-on-LAN settings structure.
*
- * This function configures Wake-on-LAN (WoL) settings for a specified port.
- * It validates the provided WoL options, checks if PME is enabled via the
- * switch's PME Pin Control Register, clears any previous wake reasons,
- * and sets the Magic Packet flag in the port's PME control register if
+ * This function configures Wake-on-LAN (WoL) settings for a specified
+ * port. It validates the provided WoL options, checks if PME is
+ * enabled and supported, clears any previous wake reasons, and sets
+ * the Magic Packet flag in the port's PME control register if
* specified.
*
* Return: 0 on success, or other error codes on failure.
*/
-int ksz9477_set_wol(struct ksz_device *dev, int port,
- struct ethtool_wolinfo *wol)
+static int ksz_set_wol(struct dsa_switch *ds, int port,
+ struct ethtool_wolinfo *wol)
{
u8 pme_ctrl = 0, pme_ctrl_old = 0;
+ struct ksz_device *dev = ds->priv;
+ const u16 *regs = dev->info->regs;
bool magic_switched_off;
bool magic_switched_on;
int ret;
@@ -3814,10 +3805,13 @@ int ksz9477_set_wol(struct ksz_device *dev, int port,
if (wol->wolopts & ~(WAKE_PHY | WAKE_MAGIC))
return -EINVAL;
+ if (!is_ksz9477(dev))
+ return -EOPNOTSUPP;
+
if (!dev->wakeup_source)
return -EOPNOTSUPP;
- ret = ksz9477_handle_wake_reason(dev, port);
+ ret = ksz_handle_wake_reason(dev, port);
if (ret)
return ret;
@@ -3826,7 +3820,8 @@ int ksz9477_set_wol(struct ksz_device *dev, int port,
if (wol->wolopts & WAKE_PHY)
pme_ctrl |= PME_WOL_LINKUP | PME_WOL_ENERGY;
- ret = ksz_pread8(dev, port, REG_PORT_PME_CTRL, &pme_ctrl_old);
+ ret = dev->dev_ops->pme_pread8(dev, port, regs[REG_PORT_PME_CTRL],
+ &pme_ctrl_old);
if (ret)
return ret;
@@ -3849,7 +3844,8 @@ int ksz9477_set_wol(struct ksz_device *dev, int port,
ksz_switch_macaddr_put(dev->ds);
}
- ret = ksz_pwrite8(dev, port, REG_PORT_PME_CTRL, pme_ctrl);
+ ret = dev->dev_ops->pme_pwrite8(dev, port, regs[REG_PORT_PME_CTRL],
+ pme_ctrl);
if (ret) {
if (magic_switched_on)
ksz_switch_macaddr_put(dev->ds);
@@ -3860,7 +3856,7 @@ int ksz9477_set_wol(struct ksz_device *dev, int port,
}
/**
- * ksz9477_handle_wake_reason - Handle wake reason on a specified port.
+ * ksz_handle_wake_reason - Handle wake reason on a specified port.
* @dev: The device structure.
* @port: The port number.
*
@@ -3872,12 +3868,14 @@ int ksz9477_set_wol(struct ksz_device *dev, int port,
*
* Return: 0 on success, or an error code on failure.
*/
-static int ksz9477_handle_wake_reason(struct ksz_device *dev, int port)
+int ksz_handle_wake_reason(struct ksz_device *dev, int port)
{
+ const u16 *regs = dev->info->regs;
u8 pme_status;
int ret;
- ret = ksz_pread8(dev, port, REG_PORT_PME_STATUS, &pme_status);
+ ret = dev->dev_ops->pme_pread8(dev, port, regs[REG_PORT_PME_STATUS],
+ &pme_status);
if (ret)
return ret;
@@ -3889,11 +3887,12 @@ static int ksz9477_handle_wake_reason(struct ksz_device *dev, int port)
pme_status & PME_WOL_LINKUP ? " \"Link Up\"" : "",
pme_status & PME_WOL_ENERGY ? " \"Energy detect\"" : "");
- return ksz_pwrite8(dev, port, REG_PORT_PME_STATUS, pme_status);
+ return dev->dev_ops->pme_pwrite8(dev, port, regs[REG_PORT_PME_STATUS],
+ pme_status);
}
/**
- * ksz9477_wol_pre_shutdown - Prepares the switch device for shutdown while
+ * ksz_wol_pre_shutdown - Prepares the switch device for shutdown while
* considering Wake-on-LAN (WoL) settings.
* @dev: The switch device structure.
* @wol_enabled: Pointer to a boolean which will be set to true if WoL is
@@ -3904,32 +3903,37 @@ static int ksz9477_handle_wake_reason(struct ksz_device *dev, int port)
* the wol_enabled flag accordingly to reflect whether WoL is active on any
* port.
*/
-void ksz9477_wol_pre_shutdown(struct ksz_device *dev, bool *wol_enabled)
+static void ksz_wol_pre_shutdown(struct ksz_device *dev, bool *wol_enabled)
{
+ const u16 *regs = dev->info->regs;
struct dsa_port *dp;
int ret;
*wol_enabled = false;
+ if (!is_ksz9477(dev))
+ return;
+
if (!dev->wakeup_source)
return;
dsa_switch_for_each_user_port(dp, dev->ds) {
u8 pme_ctrl = 0;
- ret = ksz_pread8(dev, dp->index, REG_PORT_PME_CTRL, &pme_ctrl);
+ ret = dev->dev_ops->pme_pread8(dev, dp->index,
+ regs[REG_PORT_PME_CTRL], &pme_ctrl);
if (!ret && pme_ctrl)
*wol_enabled = true;
/* make sure there are no pending wake events which would
* prevent the device from going to sleep/shutdown.
*/
- ksz9477_handle_wake_reason(dev, dp->index);
+ ksz_handle_wake_reason(dev, dp->index);
}
/* Now we are save to enable PME pin. */
if (*wol_enabled)
- ksz_write8(dev, REG_SW_PME_CTRL, PME_ENABLE);
+ dev->dev_ops->pme_write8(dev, regs[REG_SW_PME_CTRL], PME_ENABLE);
}
static int ksz_port_set_mac_address(struct dsa_switch *ds, int port,
@@ -4237,8 +4241,7 @@ void ksz_switch_shutdown(struct ksz_device *dev)
{
bool wol_enabled = false;
- if (dev->dev_ops->wol_pre_shutdown)
- dev->dev_ops->wol_pre_shutdown(dev, &wol_enabled);
+ ksz_wol_pre_shutdown(dev, &wol_enabled);
if (dev->dev_ops->reset && !wol_enabled)
dev->dev_ops->reset(dev);
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index 5f0a628b9849..c60c218afa64 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -235,6 +235,9 @@ enum ksz_regs {
S_MULTICAST_CTRL,
P_XMII_CTRL_0,
P_XMII_CTRL_1,
+ REG_SW_PME_CTRL,
+ REG_PORT_PME_STATUS,
+ REG_PORT_PME_CTRL,
};
enum ksz_masks {
@@ -354,6 +357,11 @@ struct ksz_dev_ops {
void (*get_caps)(struct ksz_device *dev, int port,
struct phylink_config *config);
int (*change_mtu)(struct ksz_device *dev, int port, int mtu);
+ int (*pme_write8)(struct ksz_device *dev, u32 reg, u8 value);
+ int (*pme_pread8)(struct ksz_device *dev, int port, int offset,
+ u8 *data);
+ int (*pme_pwrite8)(struct ksz_device *dev, int port, int offset,
+ u8 data);
void (*freeze_mib)(struct ksz_device *dev, int port, bool freeze);
void (*port_init_cnt)(struct ksz_device *dev, int port);
void (*phylink_mac_link_up)(struct ksz_device *dev, int port,
@@ -363,11 +371,6 @@ struct ksz_dev_ops {
int duplex, bool tx_pause, bool rx_pause);
void (*setup_rgmii_delay)(struct ksz_device *dev, int port);
int (*tc_cbs_set_cinc)(struct ksz_device *dev, int port, u32 val);
- void (*get_wol)(struct ksz_device *dev, int port,
- struct ethtool_wolinfo *wol);
- int (*set_wol)(struct ksz_device *dev, int port,
- struct ethtool_wolinfo *wol);
- void (*wol_pre_shutdown)(struct ksz_device *dev, bool *wol_enabled);
void (*config_cpu_port)(struct dsa_switch *ds);
int (*enable_stp_addr)(struct ksz_device *dev);
int (*reset)(struct ksz_device *dev);
@@ -391,6 +394,7 @@ int ksz_switch_macaddr_get(struct dsa_switch *ds, int port,
struct netlink_ext_ack *extack);
void ksz_switch_macaddr_put(struct dsa_switch *ds);
void ksz_switch_shutdown(struct ksz_device *dev);
+int ksz_handle_wake_reason(struct ksz_device *dev, int port);
/* Common register access functions */
static inline struct regmap *ksz_regmap_8(struct ksz_device *dev)
@@ -629,6 +633,11 @@ static inline bool is_ksz8(struct ksz_device *dev)
return ksz_is_ksz87xx(dev) || ksz_is_ksz88x3(dev);
}
+static inline bool is_ksz9477(struct ksz_device *dev)
+{
+ return dev->chip_id == KSZ9477_CHIP_ID;
+}
+
static inline int is_lan937x(struct ksz_device *dev)
{
return dev->chip_id == LAN9370_CHIP_ID ||
@@ -695,6 +704,14 @@ static inline bool is_lan937x_tx_phy(struct ksz_device *dev, int port)
#define P_MII_MAC_MODE BIT(2)
#define P_MII_SEL_M 0x3
+/* KSZ9477, KSZ8795 Wake-on-LAN (WoL) masks */
+#define PME_WOL_MAGICPKT BIT(2)
+#define PME_WOL_LINKUP BIT(1)
+#define PME_WOL_ENERGY BIT(0)
+
+#define PME_ENABLE BIT(1)
+#define PME_POLARITY BIT(0)
+
/* Interrupt */
#define REG_SW_PORT_INT_STATUS__1 0x001B
#define REG_SW_PORT_INT_MASK__1 0x001F
--
2.43.0
Powered by blists - more mailing lists