[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <Zyx46O0qLtXAs80X@orbyte.nwl.cc>
Date: Thu, 7 Nov 2024 09:23:04 +0100
From: Phil Sutter <phil@....cc>
To: Hangbin Liu <liuhangbin@...il.com>
Cc: netdev@...r.kernel.org, "Jason A. Donenfeld" <Jason@...c4.com>,
Shuah Khan <shuah@...nel.org>,
"David S. Miller" <davem@...emloft.net>,
Florian Westphal <fw@...len.de>, wireguard@...ts.zx2c4.com,
linux-kselftest@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH net-next] selftests: wireguards: use nft by default
Hi Liu Hangbin,
On Thu, Nov 07, 2024 at 02:54:38AM +0000, Hangbin Liu wrote:
> Use nft by default if it's supported, as nft is the replacement for iptables,
> which is used by default in some releases. Additionally, iptables is dropped
> in some releases.
>
> Signed-off-by: Hangbin Liu <liuhangbin@...il.com>
> ---
> CC nft developers to see if there are any easier configurations,
> as I'm not very familiar with nft commands.
Basically looks good, just a few minor remarks:
> ---
> tools/testing/selftests/wireguard/netns.sh | 63 ++++++++++++++++++----
> 1 file changed, 53 insertions(+), 10 deletions(-)
>
> diff --git a/tools/testing/selftests/wireguard/netns.sh b/tools/testing/selftests/wireguard/netns.sh
> index 405ff262ca93..4e29c1a7003c 100755
> --- a/tools/testing/selftests/wireguard/netns.sh
> +++ b/tools/testing/selftests/wireguard/netns.sh
> @@ -44,6 +44,7 @@ sleep() { read -t "$1" -N 1 || true; }
> waitiperf() { pretty "${1//*-}" "wait for iperf:${3:-5201} pid $2"; while [[ $(ss -N "$1" -tlpH "sport = ${3:-5201}") != *\"iperf3\",pid=$2,fd=* ]]; do sleep 0.1; done; }
> waitncatudp() { pretty "${1//*-}" "wait for udp:1111 pid $2"; while [[ $(ss -N "$1" -ulpH 'sport = 1111') != *\"ncat\",pid=$2,fd=* ]]; do sleep 0.1; done; }
> waitiface() { pretty "${1//*-}" "wait for $2 to come up"; ip netns exec "$1" bash -c "while [[ \$(< \"/sys/class/net/$2/operstate\") != up ]]; do read -t .1 -N 0 || true; done;"; }
> +use_nft() { nft --version &> /dev/null; }
>
> cleanup() {
> set +e
> @@ -196,13 +197,23 @@ ip1 link set wg0 mtu 1300
> ip2 link set wg0 mtu 1300
> n1 wg set wg0 peer "$pub2" endpoint 127.0.0.1:2
> n2 wg set wg0 peer "$pub1" endpoint 127.0.0.1:1
> -n0 iptables -A INPUT -m length --length 1360 -j DROP
> +if use_nft; then
> + n0 nft add table inet filter
Using inet family captures IPv6 traffic, too. You don't seem to
explicitly configure it, but the usual auto-config traffic may offset
rule counters. If you care about such side-effects, you may want to use
ip family instead.
Tables are family-specific, but generic otherwise. So you could add a
table for testing in each netns up front:
| if use_nft; then
| n0 nft add table ip wgtest
| n1 nft add table ip wgtest
| n2 nft add table ip wgtest
| fi
> + n0 nft add chain inet filter INPUT { type filter hook input priority filter \; policy accept \; }
> + n0 nft add rule inet filter INPUT meta length 1360 counter drop
> +else
> + n0 iptables -A INPUT -m length --length 1360 -j DROP
> +fi
> n1 ip route add 192.168.241.2/32 dev wg0 mtu 1299
> n2 ip route add 192.168.241.1/32 dev wg0 mtu 1299
> n2 ping -c 1 -W 1 -s 1269 192.168.241.1
> n2 ip route delete 192.168.241.1/32 dev wg0 mtu 1299
> n1 ip route delete 192.168.241.2/32 dev wg0 mtu 1299
> -n0 iptables -F INPUT
> +if use_nft; then
> + n0 nft delete table inet filter
Here just flush the table (drops only the rules):
| n0 nft flush table ip wgtest
Cheers, Phil
Powered by blists - more mailing lists