| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <671c20540702230841w640e59d5uf928bac0bbfa8baa@mail.gmail.com>
Date: Fri, 23 Feb 2007 11:41:24 -0500
From: "Tom Burns" <tom.i.burns@...il.com>
To: "Francois Romieu" <romieu@...zoreil.com>
Cc: linux-kernel@...r.kernel.org
Subject: Re: [r8169] Any success with RTL8110SC?
Hi Francois,
Thanks for your reply.
On 2/22/07, Francois Romieu <romieu@...zoreil.com> wrote:
[...]
> I do not have the answar that you expect but some information could help:
> - which motherboard is it ?
> - can you send a dmesg for 2.6.20.1 as well as a lspci -vvx from your
> computer ?
The motherboard is the latest revision of the MB720F mini ITX:
http://www.ibase-i.com.tw/mb720.htm
I have attached my dmesg and lspci -vvx output at the bottom of the message.
> > The r1000 driver seems to be able to send data on the wire for about a
> > minute, receive packets back about 5% of the time, and after a minute
> > stop working altogether, complaining that the "send buffer is full."
>
> If I read you correctly, this version of the driver is less broken than
> the others, right ?
Correct. On this board none of the versions of r8169 I backported to
2.6.15-1 were able to successfully put any data on the wire. The eth
interface gets created, and the device does properly report the link
status up/down (as shown at the bottom of the dmesg output below), but
that's it afaik. The r1000 driver sends a bit of data as I had
elaborated in the original email.
> If you are brave, you can try the patch below against 2.6.20-rc1:
> http://www.fr.zoreil.com/people/francois/misc/20070221-2.6.21-rc1-r8169-test.patch
Thanks for providing that - however I just tried it, and I get the
same results as with module I backported from 2.6.20 (that is, device
is recognized but no data is sent on the wire).
===== output from lspci -vvx =====
00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
Subsystem: VIA Technologies, Inc. CN400/PM880 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Capabilities: [80] AGP version 3.5
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 59 02 06 00 30 22 00 00 00 06 00 08 80 00
10: 08 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 59 02
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 06 11 59 12 06 00 00 02 00 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 06 11 59 22 06 00 00 02 00 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 06 11 59 32 06 00 00 02 00 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 06 11 59 42 06 00 00 02 00 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 06 11 59 72 06 00 00 02 00 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f4000000-f5ffffff
Prefetchable memory behind bridge: f0000000-f3ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR+ <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 98 b1 07 01 30 02 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 20 e2
20: 00 f4 f0 f5 00 f0 f0 f3 00 00 00 00 00 00 00 00
30: 00 00 00 00 70 00 00 00 00 00 00 00 00 00 0a 00
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Unknown
device 8167 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Unknown device 8167
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at f6023000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 10000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
00: ec 10 67 81 07 00 b0 02 10 00 00 02 08 20 00 00
10: 01 d0 00 00 00 30 02 f6 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 67 81
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 20 40
00:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f6020000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at e600 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 44 30 07 00 10 02 80 10 00 0c 08 20 00 00
10: 00 00 02 f6 01 e6 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 44 30
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 20
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID
Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at ed00 [size=4]
Region 2: I/O ports at ee00 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e500 [size=16]
Region 5: I/O ports at d400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 49 31 07 00 90 02 80 8f 01 01 00 20 80 00
10: 01 ec 00 00 01 ed 00 00 01 ee 00 00 01 e4 00 00
20: 01 e5 00 00 01 d4 00 00 00 00 00 00 06 11 49 31
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 02 00 00
00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 5
Region 4: I/O ports at e700 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e7 00 00 00 00 00 00 00 00 00 00 06 11 71 05
30: 00 00 00 00 c0 00 00 00 00 00 00 00 05 01 00 00
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 5
Region 4: I/O ports at e800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e8 00 00 00 00 00 00 00 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 5
Region 4: I/O ports at e900 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e9 00 00 00 00 00 00 00 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at ea00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 ea 00 00 00 00 00 00 00 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at eb00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 eb 00 00 00 00 00 00 00 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
(prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin C routed to IRQ 6
Region 0: Memory at f6021000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 04 31 17 00 10 02 86 20 03 0c 08 20 80 00
10: 00 10 02 f6 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 04 31
30: 00 00 00 00 80 00 00 00 00 00 00 00 06 03 00 00
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[KT600/K8T800/K8T890 South]
Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 27 32 87 00 10 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 27 32
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
Subsystem: Avance Logic Inc. Unknown device 4760
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 6
Region 0: I/O ports at d800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 59 30 01 00 10 02 60 00 01 04 00 00 00 00
10: 01 d8 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 05 40 60 47
30: 00 00 00 00 c0 00 00 00 00 00 00 00 06 03 00 00
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet
Controller on VT8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at e000 [size=256]
Region 1: Memory at f6022000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 65 30 07 00 10 02 78 00 00 02 08 20 00 00
10: 01 e0 00 00 00 20 02 f6 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 02 01
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 03 08
01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome
Pro VGA Adapter (rev 02) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. S3 Unichrome Pro VGA Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at f5000000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
00: 06 11 18 31 07 00 30 02 02 00 00 03 00 20 00 00
10: 08 00 00 f0 00 00 00 f4 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 18 31
30: 00 00 00 00 60 00 00 00 00 00 00 00 05 01 02 00
===== end lspci -vvx =====
===== output of dmesg with r8169.c module from 2.6.20 =====
Linux version 2.6.15-1.2054_FC5
(bhcompile@...0-bc1-3.build.redhat.com) (gcc version 4.1.0 20060304
(Red Hat 4.1.0-3)) #1 Tue Mar 14 15:48:33 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bdf0000 (usable)
BIOS-e820: 000000000bdf0000 - 000000000bdf3000 (ACPI NVS)
BIOS-e820: 000000000bdf3000 - 000000000be00000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
189MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 48624
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 44528 pages, LIFO batch:7
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
Allocating PCI resources starting at 10000000 (gap: 0be00000:f2e00000)
Built 1 zonelists
Kernel command line: ro root=/dev/sda1 vga=785 noapic acpi=off
No local APIC present or hardware disabled
mapped APIC to ffffd000 (0117e000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c03d4000 soft=c03d3000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1399.535 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 187932k/194496k available (1914k kernel code, 6048k reserved,
774k data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2805.00 BogoMIPS (lpj=5610006)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000
00000000 000000dc 00000000
CPU: Centaur VIA Nehemiah stepping 0a
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 997k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf9f20, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
PCI: Found IRQ 5 for device 0000:00:0f.1
PCI: Sharing IRQ 5 with 0000:00:10.0
PCI: Sharing IRQ 5 with 0000:00:10.1
PCI: Sharing IRQ 5 with 0000:00:12.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f4000000-f5ffffff
PREFETCH window: f0000000-f3ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1172277235.532:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key EE596B44DDA71123
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Bypassing VIA 8237 APIC De-Assert Message
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xf0000000, mapped to 0xcc880000, using 1200k,
total 65536k
vesafb: mode is 640x480x16, linelength=1280, pages=101
vesafb: protected mode interface info at c000:a585
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 80x30
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset
agpgart: AGP aperture is 128M @ 0xe8000000
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 11) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: Found IRQ 5 for device 0000:00:0f.1
PCI: Sharing IRQ 5 with 0000:00:10.0
PCI: Sharing IRQ 5 with 0000:00:10.1
PCI: Sharing IRQ 5 with 0000:00:12.0
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 5
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xe700-0xe707, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xe708-0xe70f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 176k freed
Write protecting the kernel read-only data: 359k
SCSI subsystem initialized
input: PS2++ Logitech Wheel Mouse as /class/input/input1
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
PCI: Found IRQ 10 for device 0000:00:0f.0
PCI: Sharing IRQ 10 with 0000:00:0a.0
PCI: Sharing IRQ 10 with 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:10.3
sata_via 0000:00:0f.0: routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xED02 bmdma 0xE500 irq 10
ata2: SATA max UDMA/133 cmd 0xEE00 ctl 0xE402 bmdma 0xE508 irq 10
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:7469 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: SATA link down (SStatus 0)
scsi1 : sata_via
Vendor: ATA Model: WDC WD800JD-22LS Rev: 06.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
PCI: Found IRQ 5 for device 0000:00:12.0
PCI: Sharing IRQ 5 with 0000:00:0f.1
PCI: Sharing IRQ 5 with 0000:00:10.0
PCI: Sharing IRQ 5 with 0000:00:10.1
eth0: VIA Rhine II at 0xf6022000, 00:03:2d:0a:c9:21, IRQ 5.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link c5e1.
PCI: Found IRQ 6 for device 0000:00:11.5
PCI: Sharing IRQ 6 with 0000:00:10.4
PCI: Setting latency timer of device 0000:00:11.5 to 64
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 5 for device 0000:00:10.0
PCI: Sharing IRQ 5 with 0000:00:0f.1
PCI: Sharing IRQ 5 with 0000:00:10.1
PCI: Sharing IRQ 5 with 0000:00:12.0
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 5, io base 0x0000e800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
PCI: Found IRQ 5 for device 0000:00:10.1
PCI: Sharing IRQ 5 with 0000:00:0f.1
PCI: Sharing IRQ 5 with 0000:00:10.0
PCI: Sharing IRQ 5 with 0000:00:12.0
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 5, io base 0x0000e900
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:0a.0
PCI: Sharing IRQ 10 with 0000:00:0f.0
PCI: Sharing IRQ 10 with 0000:00:10.3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 10, io base 0x0000ea00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:10.3
PCI: Sharing IRQ 10 with 0000:00:0a.0
PCI: Sharing IRQ 10 with 0000:00:0f.0
PCI: Sharing IRQ 10 with 0000:00:10.2
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 10, io base 0x0000eb00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ieee1394: Initialized config rom entry `ip1394'
PCI: Found IRQ 10 for device 0000:00:0c.0
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10]
MMIO=[f6020000-f60207ff] Max Packet=[2048] IR/IT contexts=[4/8]
PCI: Found IRQ 6 for device 0000:00:10.4
PCI: Sharing IRQ 6 with 0000:00:11.5
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 6, io mem 0xf6021000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Non-volatile memory driver v1.2
floppy0: Unable to grab IRQ6 for the floppy driver
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000000032d1122ad]
lp0: using parport0 (polling).
lp0: console ready
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@...hat.com
EXT3 FS on sda1, internal journal
Adding 522104k swap on /dev/sda2. Priority:-1 extents:1 across:522104k
eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
PCI: Found IRQ 10 for device 0000:00:0a.0
PCI: Sharing IRQ 10 with 0000:00:0f.0
PCI: Sharing IRQ 10 with 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:10.3
eth1: RTL8169sc/8110sc at 0xccbca000, 00:03:2d:0a:c9:20, IRQ 10
r8169: eth1: link down
eth0: link down
r8169: eth1: link up
Cheers,
Tom
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists