| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <671c20540702260755heb107e9v55af2f80f7e49c4@mail.gmail.com> Date: Mon, 26 Feb 2007 10:55:13 -0500 From: "Tom Burns" <tom.i.burns@...il.com> To: "Francois Romieu" <romieu@...zoreil.com> Cc: linux-kernel@...r.kernel.org Subject: Re: [r8169] Any success with RTL8110SC? Hi again Francois, list, I've realized now that in reality, the r8169 driver (2.6.20-1 backported to 2.6.15-1, with the patch from Francois' first email applied) is receiving data! Just not transmitting any. tcpdump shows valid packets on the LAN, but ifconfig reports 0 packets transferred. Hope this helps. Cheers, Tom On 2/23/07, Tom Burns <tom.i.burns@...il.com> wrote: > Hi Francois, > > Thanks for your reply. > > On 2/22/07, Francois Romieu <romieu@...zoreil.com> wrote: > [...] > > I do not have the answar that you expect but some information could help: > > - which motherboard is it ? > > - can you send a dmesg for 2.6.20.1 as well as a lspci -vvx from your > > computer ? > > The motherboard is the latest revision of the MB720F mini ITX: > http://www.ibase-i.com.tw/mb720.htm > > I have attached my dmesg and lspci -vvx output at the bottom of the message. > > > > The r1000 driver seems to be able to send data on the wire for about a > > > minute, receive packets back about 5% of the time, and after a minute > > > stop working altogether, complaining that the "send buffer is full." > > > > If I read you correctly, this version of the driver is less broken than > > the others, right ? > > Correct. On this board none of the versions of r8169 I backported to > 2.6.15-1 were able to successfully put any data on the wire. The eth > interface gets created, and the device does properly report the link > status up/down (as shown at the bottom of the dmesg output below), but > that's it afaik. The r1000 driver sends a bit of data as I had > elaborated in the original email. > > > If you are brave, you can try the patch below against 2.6.20-rc1: > > http://www.fr.zoreil.com/people/francois/misc/20070221-2.6.21-rc1-r8169-test.patch > > Thanks for providing that - however I just tried it, and I get the > same results as with module I backported from 2.6.20 (that is, device > is recognized but no data is sent on the wire). > > ===== output from lspci -vvx ===== > > 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Subsystem: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ >SERR- <PERR- > Latency: 8 > Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] > Capabilities: [80] AGP version 3.5 > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- > FW+ AGP3+ Rate=x4,x8 > Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 59 02 06 00 30 22 00 00 00 06 00 08 80 00 > 10: 08 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 59 02 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 12 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 22 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 32 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 42 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > > 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > 00: 06 11 59 72 06 00 00 02 00 00 00 06 00 00 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 > > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if > 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > Memory behind bridge: f4000000-f5ffffff > Prefetchable memory behind bridge: f0000000-f3ffffff > Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR+ <PERR+ > BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- > Capabilities: [70] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 98 b1 07 01 30 02 00 00 04 06 00 00 01 00 > 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 20 e2 > 20: 00 f4 f0 f5 00 f0 f0 f3 00 00 00 00 00 00 00 00 > 30: 00 00 00 00 70 00 00 00 00 00 00 00 00 00 0a 00 > > 00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Unknown > device 8167 (rev 10) > Subsystem: Realtek Semiconductor Co., Ltd. Unknown device 8167 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (8000ns min, 16000ns max), Cache Line Size 08 > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at d000 [size=256] > Region 1: Memory at f6023000 (32-bit, non-prefetchable) [size=256] > [virtual] Expansion ROM at 10000000 [disabled] [size=128K] > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable+ DSel=0 DScale=0 PME- > 00: ec 10 67 81 07 00 b0 02 10 00 00 02 08 20 00 00 > 10: 01 d0 00 00 00 30 02 f6 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 67 81 > 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 20 40 > > 00:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host > Controller (rev 80) (prog-if 10 [OHCI]) > Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (8000ns max), Cache Line Size 08 > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at f6020000 (32-bit, non-prefetchable) [size=2K] > Region 1: I/O ports at e600 [size=128] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 44 30 07 00 10 02 80 10 00 0c 08 20 00 00 > 10: 00 00 02 f6 01 e6 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 44 30 > 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 20 > > 00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID > Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO]) > Subsystem: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 > Interrupt: pin B routed to IRQ 10 > Region 0: I/O ports at ec00 [size=8] > Region 1: I/O ports at ed00 [size=4] > Region 2: I/O ports at ee00 [size=8] > Region 3: I/O ports at e400 [size=4] > Region 4: I/O ports at e500 [size=16] > Region 5: I/O ports at d400 [size=256] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 49 31 07 00 90 02 80 8f 01 01 00 20 80 00 > 10: 01 ec 00 00 01 ed 00 00 01 ee 00 00 01 e4 00 00 > 20: 01 e5 00 00 01 d4 00 00 00 00 00 00 06 11 49 31 > 30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 02 00 00 > > 00:0f.1 IDE interface: VIA Technologies, Inc. > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) > (prog-if 8a [Master SecP PriP]) > Subsystem: VIA Technologies, Inc. > VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 > Interrupt: pin A routed to IRQ 5 > Region 4: I/O ports at e700 [size=16] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 e7 00 00 00 00 00 00 00 00 00 00 06 11 71 05 > 30: 00 00 00 00 c0 00 00 00 00 00 00 00 05 01 00 00 > > 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin A routed to IRQ 5 > Region 4: I/O ports at e800 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 e8 00 00 00 00 00 00 00 00 00 00 06 11 38 30 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00 > > 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin A routed to IRQ 5 > Region 4: I/O ports at e900 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 e9 00 00 00 00 00 00 00 00 00 00 06 11 38 30 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00 > > 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin B routed to IRQ 10 > Region 4: I/O ports at ea00 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 ea 00 00 00 00 00 00 00 00 00 00 06 11 38 30 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00 > > 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin B routed to IRQ 10 > Region 4: I/O ports at eb00 [size=32] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 38 30 07 00 10 02 81 00 03 0c 08 20 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 01 eb 00 00 00 00 00 00 00 00 00 00 06 11 38 30 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00 > > 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) > (prog-if 20 [EHCI]) > Subsystem: VIA Technologies, Inc. USB 2.0 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32, Cache Line Size 08 > Interrupt: pin C routed to IRQ 6 > Region 0: Memory at f6021000 (32-bit, non-prefetchable) [size=256] > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 04 31 17 00 10 02 86 20 03 0c 08 20 80 00 > 10: 00 10 02 f6 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 04 31 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 06 03 00 00 > > 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge > [KT600/K8T800/K8T890 South] > Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping+ SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 27 32 87 00 10 02 00 00 01 06 00 00 80 00 > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 27 32 > 30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 > > 00:11.5 Multimedia audio controller: VIA Technologies, Inc. > VT8233/A/8235/8237 AC97 Audio Controller (rev 60) > Subsystem: Avance Logic Inc. Unknown device 4760 > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Interrupt: pin C routed to IRQ 6 > Region 0: I/O ports at d800 [size=256] > Capabilities: [c0] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 59 30 01 00 10 02 60 00 01 04 00 00 00 00 > 10: 01 d8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 05 40 60 47 > 30: 00 00 00 00 c0 00 00 00 00 00 00 00 06 03 00 00 > > 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78) > Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet > Controller on VT8235 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (750ns min, 2000ns max), Cache Line Size 08 > Interrupt: pin A routed to IRQ 5 > Region 0: I/O ports at e000 [size=256] > Region 1: Memory at f6022000 (32-bit, non-prefetchable) [size=256] > Capabilities: [40] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > 00: 06 11 65 30 07 00 10 02 78 00 00 02 08 20 00 00 > 10: 01 e0 00 00 00 20 02 f6 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 02 01 > 30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 03 08 > > 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome > Pro VGA Adapter (rev 02) (prog-if 00 [VGA]) > Subsystem: VIA Technologies, Inc. S3 Unichrome Pro VGA Adapter > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (500ns min) > Interrupt: pin A routed to IRQ 5 > Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] > Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=16M] > [virtual] Expansion ROM at f5000000 [disabled] [size=64K] > Capabilities: [60] Power Management version 2 > Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [70] AGP version 3.0 > Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- > 64bit- FW- AGP3+ Rate=x4,x8 > Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none> > 00: 06 11 18 31 07 00 30 02 02 00 00 03 00 20 00 00 > 10: 08 00 00 f0 00 00 00 f4 00 00 00 00 00 00 00 00 > 20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 18 31 > 30: 00 00 00 00 60 00 00 00 00 00 00 00 05 01 02 00 > > ===== end lspci -vvx ===== > > ===== output of dmesg with r8169.c module from 2.6.20 ===== > > Linux version 2.6.15-1.2054_FC5 > (bhcompile@...0-bc1-3.build.redhat.com) (gcc version 4.1.0 20060304 > (Red Hat 4.1.0-3)) #1 Tue Mar 14 15:48:33 EST 2006 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000000bdf0000 (usable) > BIOS-e820: 000000000bdf0000 - 000000000bdf3000 (ACPI NVS) > BIOS-e820: 000000000bdf3000 - 000000000be00000 (ACPI data) > BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > 0MB HIGHMEM available. > 189MB LOWMEM available. > Using x86 segment limits to approximate NX protection > On node 0 totalpages: 48624 > DMA zone: 4096 pages, LIFO batch:0 > DMA32 zone: 0 pages, LIFO batch:0 > Normal zone: 44528 pages, LIFO batch:7 > HighMem zone: 0 pages, LIFO batch:0 > DMI 2.3 present. > Allocating PCI resources starting at 10000000 (gap: 0be00000:f2e00000) > Built 1 zonelists > Kernel command line: ro root=/dev/sda1 vga=785 noapic acpi=off > No local APIC present or hardware disabled > mapped APIC to ffffd000 (0117e000) > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Initializing CPU#0 > CPU 0 irqstacks, hard=c03d4000 soft=c03d3000 > PID hash table entries: 1024 (order: 10, 16384 bytes) > Detected 1399.535 MHz processor. > Using tsc for high-res timesource > Console: colour dummy device 80x25 > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) > Memory: 187932k/194496k available (1914k kernel code, 6048k reserved, > 774k data, 176k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > Calibrating delay using timer specific routine.. 2805.00 BogoMIPS (lpj=5610006) > Security Framework v1.0.0 initialized > SELinux: Initializing. > SELinux: Starting in permissive mode > selinux_register_security: Registering secondary module capability > Capability LSM initialized as secondary > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000 > 00000000 00000000 00000000 > CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line) > CPU: L2 Cache: 64K (32 bytes/line) > CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000 > 00000000 000000dc 00000000 > CPU: Centaur VIA Nehemiah stepping 0a > Checking 'hlt' instruction... OK. > checking if image is initramfs... it is > Freeing initrd memory: 997k freed > NET: Registered protocol family 16 > PCI: PCI BIOS revision 2.10 entry at 0xf9f20, last bus=1 > PCI: Using configuration type 1 > ACPI: Subsystem revision 20060127 > ACPI: Interpreter disabled. > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI: disabled > usbcore: registered new driver usbfs > usbcore: registered new driver hub > PCI: Probing PCI hardware > PCI: Probing PCI hardware (bus 00) > Boot video device is 0000:01:00.0 > PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0 > PCI: Found IRQ 5 for device 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:10.1 > PCI: Sharing IRQ 5 with 0000:00:12.0 > PCI: Bridge: 0000:00:01.0 > IO window: disabled. > MEM window: f4000000-f5ffffff > PREFETCH window: f0000000-f3ffffff > PCI: Setting latency timer of device 0000:00:01.0 to 64 > apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) > audit: initializing netlink socket (disabled) > audit(1172277235.532:1): initialized > Total HugeTLB memory allocated, 0 > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > SELinux: Registering netfilter hooks > Initializing Cryptographic API > ksign: Installing public key data > Loading keyring > - Added public key EE596B44DDA71123 > - User ID: Red Hat, Inc. (Kernel Module GPG key) > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > PCI: Bypassing VIA 8237 APIC De-Assert Message > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > vesafb: framebuffer at 0xf0000000, mapped to 0xcc880000, using 1200k, > total 65536k > vesafb: mode is 640x480x16, linelength=1280, pages=101 > vesafb: protected mode interface info at c000:a585 > vesafb: scrolling: redraw > vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 > Console: switching to colour frame buffer device 80x30 > fb0: VESA VGA frame buffer device > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Real Time Clock Driver v1.12ac > Linux agpgart interface v0.101 (c) Dave Jones > agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset > agpgart: AGP aperture is 128M @ 0xe8000000 > PNP: No PS/2 controller found. Probing ports directly. > serio: i8042 AUX port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > serial8250: ttyS2 at I/O 0x3e8 (irq = 11) is a 16550A > RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > VP_IDE: IDE controller at PCI slot 0000:00:0f.1 > PCI: Found IRQ 5 for device 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:10.1 > PCI: Sharing IRQ 5 with 0000:00:12.0 > PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 5 > VP_IDE: chipset revision 6 > VP_IDE: not 100% native mode: will probe irqs later > VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 > ide0: BM-DMA at 0xe700-0xe707, BIOS settings: hda:pio, hdb:pio > ide1: BM-DMA at 0xe708-0xe70f, BIOS settings: hdc:pio, hdd:pio > Probing IDE interface ide0... > Probing IDE interface ide1... > Probing IDE interface ide0... > Probing IDE interface ide1... > ide-floppy driver 0.99.newide > usbcore: registered new driver libusual > usbcore: registered new driver hiddev > usbcore: registered new driver usbhid > drivers/usb/input/hid-core.c: v2.6:USB HID core driver > mice: PS/2 mouse device common for all mice > md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 > md: bitmap version 4.39 > NET: Registered protocol family 2 > input: AT Translated Set 2 keyboard as /class/input/input0 > IP route cache hash table entries: 2048 (order: 1, 8192 bytes) > TCP established hash table entries: 8192 (order: 5, 131072 bytes) > TCP bind hash table entries: 8192 (order: 5, 163840 bytes) > TCP: Hash tables configured (established 8192 bind 8192) > TCP reno registered > TCP bic registered > Initializing IPsec netlink socket > NET: Registered protocol family 1 > NET: Registered protocol family 17 > Using IPI Shortcut mode > Freeing unused kernel memory: 176k freed > Write protecting the kernel read-only data: 359k > SCSI subsystem initialized > input: PS2++ Logitech Wheel Mouse as /class/input/input1 > libata version 1.20 loaded. > sata_via 0000:00:0f.0: version 1.1 > PCI: Found IRQ 10 for device 0000:00:0f.0 > PCI: Sharing IRQ 10 with 0000:00:0a.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:10.3 > sata_via 0000:00:0f.0: routed to hard irq line 10 > ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xED02 bmdma 0xE500 irq 10 > ata2: SATA max UDMA/133 cmd 0xEE00 ctl 0xE402 bmdma 0xE508 irq 10 > ata1: SATA link up 1.5 Gbps (SStatus 113) > ata1: dev 0 cfg 49:2f00 82:7469 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:407f > ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48 > ata1: dev 0 configured for UDMA/133 > scsi0 : sata_via > ata2: SATA link down (SStatus 0) > scsi1 : sata_via > Vendor: ATA Model: WDC WD800JD-22LS Rev: 06.0 > Type: Direct-Access ANSI SCSI revision: 05 > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: drive cache: write back > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: drive cache: write back > sda: sda1 sda2 > sd 0:0:0:0: Attached scsi disk sda > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > SELinux: Disabled at runtime. > SELinux: Unregistering netfilter hooks > via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker > PCI: Found IRQ 5 for device 0000:00:12.0 > PCI: Sharing IRQ 5 with 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:10.1 > eth0: VIA Rhine II at 0xf6022000, 00:03:2d:0a:c9:21, IRQ 5. > eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link c5e1. > PCI: Found IRQ 6 for device 0000:00:11.5 > PCI: Sharing IRQ 6 with 0000:00:10.4 > PCI: Setting latency timer of device 0000:00:11.5 to 64 > USB Universal Host Controller Interface driver v2.3 > PCI: Found IRQ 5 for device 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.1 > PCI: Sharing IRQ 5 with 0000:00:12.0 > uhci_hcd 0000:00:10.0: UHCI Host Controller > uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 > uhci_hcd 0000:00:10.0: irq 5, io base 0x0000e800 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > sd 0:0:0:0: Attached scsi generic sg0 type 0 > PCI: Found IRQ 5 for device 0000:00:10.1 > PCI: Sharing IRQ 5 with 0000:00:0f.1 > PCI: Sharing IRQ 5 with 0000:00:10.0 > PCI: Sharing IRQ 5 with 0000:00:12.0 > uhci_hcd 0000:00:10.1: UHCI Host Controller > uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 > uhci_hcd 0000:00:10.1: irq 5, io base 0x0000e900 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > PCI: Found IRQ 10 for device 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:0a.0 > PCI: Sharing IRQ 10 with 0000:00:0f.0 > PCI: Sharing IRQ 10 with 0000:00:10.3 > uhci_hcd 0000:00:10.2: UHCI Host Controller > uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 > uhci_hcd 0000:00:10.2: irq 10, io base 0x0000ea00 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > PCI: Found IRQ 10 for device 0000:00:10.3 > PCI: Sharing IRQ 10 with 0000:00:0a.0 > PCI: Sharing IRQ 10 with 0000:00:0f.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > uhci_hcd 0000:00:10.3: UHCI Host Controller > uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 > uhci_hcd 0000:00:10.3: irq 10, io base 0x0000eb00 > usb usb4: configuration #1 chosen from 1 choice > hub 4-0:1.0: USB hub found > hub 4-0:1.0: 2 ports detected > ieee1394: Initialized config rom entry `ip1394' > PCI: Found IRQ 10 for device 0000:00:0c.0 > ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] > MMIO=[f6020000-f60207ff] Max Packet=[2048] IR/IT contexts=[4/8] > PCI: Found IRQ 6 for device 0000:00:10.4 > PCI: Sharing IRQ 6 with 0000:00:11.5 > ehci_hcd 0000:00:10.4: EHCI Host Controller > ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 > ehci_hcd 0000:00:10.4: irq 6, io mem 0xf6021000 > ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb5: configuration #1 chosen from 1 choice > hub 5-0:1.0: USB hub found > hub 5-0:1.0: 8 ports detected > Non-volatile memory driver v1.2 > floppy0: Unable to grab IRQ6 for the floppy driver > parport0: PC-style at 0x378 [PCSPP,TRISTATE] > ieee1394: Host added: ID:BUS[0-00:1023] GUID[000000032d1122ad] > lp0: using parport0 (polling). > lp0: console ready > md: Autodetecting RAID arrays. > md: autorun ... > md: ... autorun DONE. > device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@...hat.com > EXT3 FS on sda1, internal journal > Adding 522104k swap on /dev/sda2. Priority:-1 extents:1 across:522104k > eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1 > r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded > PCI: Found IRQ 10 for device 0000:00:0a.0 > PCI: Sharing IRQ 10 with 0000:00:0f.0 > PCI: Sharing IRQ 10 with 0000:00:10.2 > PCI: Sharing IRQ 10 with 0000:00:10.3 > eth1: RTL8169sc/8110sc at 0xccbca000, 00:03:2d:0a:c9:20, IRQ 10 > r8169: eth1: link down > eth0: link down > r8169: eth1: link up > > Cheers, > Tom > - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists