| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20081118222505.GD2567@pengutronix.de>
Date: Tue, 18 Nov 2008 23:25:05 +0100
From: Sascha Hauer <s.hauer@...gutronix.de>
To: Evgeniy Polyakov <zbr@...emap.net>
Cc: Andrew Morton <akpm@...ux-foundation.org>,
linux-kernel@...r.kernel.org, Luotao Fu <l.fu@...gutronix.de>
Subject: Re: [PATCH] Add 1-wire master driver for i.MX27 / i.MX31
Hi,
On Wed, Nov 19, 2008 at 01:16:13AM +0300, Evgeniy Polyakov wrote:
> From: Sascha Hauer <s.hauer@...gutronix.de>
>
> This patch adds support for the 1-wire master interface for i.MX27 and
> i.MX31.
Ack for this one, the other patches from this series need to go via
Russell King to prevent merge conflicts with other MX2 patches. Sorry, I
should have made that clear.
Sascha
>
> Signed-off-by: Luotao Fu <l.fu@...gutronix.de>
> Signed-off-by: Sascha Hauer <s.hauer@...gutronix.de>
> Signed-off-by: Evgeniy Polyakov <zbr@...emap.net>
> ---
> drivers/w1/masters/Kconfig | 6 +
> drivers/w1/masters/Makefile | 2 +
> drivers/w1/masters/mxc_w1.c | 215 +++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 223 insertions(+), 0 deletions(-)
> create mode 100644 drivers/w1/masters/mxc_w1.c
>
> diff --git a/drivers/w1/masters/Kconfig b/drivers/w1/masters/Kconfig
> index a14d5b6..f2da1a8 100644
> --- a/drivers/w1/masters/Kconfig
> +++ b/drivers/w1/masters/Kconfig
> @@ -34,6 +34,12 @@ config W1_MASTER_DS2482
> This driver can also be built as a module. If so, the module
> will be called ds2482.
>
> +config W1_MASTER_MXC
> + tristate "Freescale MXC 1-wire busmaster"
> + depends on W1 && ARCH_MXC
> + help
> + Say Y here to enable MXC 1-wire host
> +
> config W1_MASTER_DS1WM
> tristate "Maxim DS1WM 1-wire busmaster"
> depends on W1 && ARM
> diff --git a/drivers/w1/masters/Makefile b/drivers/w1/masters/Makefile
> index bc4714a..c5a3e96 100644
> --- a/drivers/w1/masters/Makefile
> +++ b/drivers/w1/masters/Makefile
> @@ -5,6 +5,8 @@
> obj-$(CONFIG_W1_MASTER_MATROX) += matrox_w1.o
> obj-$(CONFIG_W1_MASTER_DS2490) += ds2490.o
> obj-$(CONFIG_W1_MASTER_DS2482) += ds2482.o
> +obj-$(CONFIG_W1_MASTER_MXC) += mxc_w1.o
> +
> obj-$(CONFIG_W1_MASTER_DS1WM) += ds1wm.o
> obj-$(CONFIG_W1_MASTER_GPIO) += w1-gpio.o
> obj-$(CONFIG_HDQ_MASTER_OMAP) += omap_hdq.o
> diff --git a/drivers/w1/masters/mxc_w1.c b/drivers/w1/masters/mxc_w1.c
> new file mode 100644
> index 0000000..92323be
> --- /dev/null
> +++ b/drivers/w1/masters/mxc_w1.c
> @@ -0,0 +1,215 @@
> +/*
> + * Copyright 2005-2008 Freescale Semiconductor, Inc. All Rights Reserved.
> + * Copyright 2008 Luotao Fu, kernel@...gutronix.de
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; either version 2
> + * of the License, or (at your option) any later version.
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
> + *
> + */
> +
> +#include <linux/module.h>
> +#include <linux/interrupt.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +
> +#include "../w1.h"
> +#include "../w1_int.h"
> +#include "../w1_log.h"
> +
> +/* According to the mx27 Datasheet the reset procedure should take up to about
> + * 1350us. We set the timeout to 500*100us = 50ms for sure */
> +#define MXC_W1_RESET_TIMEOUT 500
> +
> +/*
> + * MXC W1 Register offsets
> + */
> +#define MXC_W1_CONTROL 0x00
> +#define MXC_W1_TIME_DIVIDER 0x02
> +#define MXC_W1_RESET 0x04
> +#define MXC_W1_COMMAND 0x06
> +#define MXC_W1_TXRX 0x08
> +#define MXC_W1_INTERRUPT 0x0A
> +#define MXC_W1_INTERRUPT_EN 0x0C
> +
> +struct mxc_w1_device {
> + void __iomem *regs;
> + unsigned int clkdiv;
> + struct clk *clk;
> + struct w1_bus_master *bus_master;
> +};
> +
> +/*
> + * this is the low level routine to
> + * reset the device on the One Wire interface
> + * on the hardware
> + */
> +static u8 mxc_w1_ds2_reset_bus(void *data)
> +{
> + u8 reg_val, rc = 1;
> + unsigned int timeout_cnt = 0;
> +
> + struct mxc_w1_device *dev = (struct mxc_w1_device *)data;
> +
> + __raw_writeb(0x80, (dev->regs + MXC_W1_CONTROL));
> +
> + while (1) {
> + reg_val = __raw_readb(dev->regs + MXC_W1_CONTROL);
> +
> + if (((reg_val >> 7) & 0x1) == 0 ||
> + timeout_cnt > MXC_W1_RESET_TIMEOUT) {
> + rc = 0;
> + break;
> + } else
> + timeout_cnt++;
> +
> + udelay(100);
> + }
> + return (reg_val >> 7) & 0x1;
> +}
> +
> +/*
> + * this is the low level routine to read/write a bit on the One Wire
> + * interface on the hardware. It does write 0 if parameter bit is set
> + * to 0, otherwise a write 1/read.
> + */
> +static u8 mxc_w1_ds2_touch_bit(void *data, u8 bit)
> +{
> + unsigned int timeout_cnt = 400;
> +
> + struct mxc_w1_device *mdev = (struct mxc_w1_device *)data;
> + void __iomem *ctrl_addr = mdev->regs + MXC_W1_CONTROL;
> +
> + __raw_writeb((1 << (5 - bit)), ctrl_addr);
> +
> + while (timeout_cnt--) {
> + if (!((__raw_readb(ctrl_addr) >> (5 - bit)) & 0x1))
> + break;
> +
> + udelay(1);
> + }
> +
> + return ((__raw_readb(ctrl_addr)) >> 3) & 0x1;
> +}
> +
> +static int __devinit mxc_w1_probe(struct platform_device *pdev)
> +{
> + struct mxc_w1_device *mdev;
> + struct resource *res;
> + int err = 0;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res)
> + return -ENODEV;
> +
> + mdev = kzalloc(sizeof(struct mxc_w1_device) +
> + sizeof(struct w1_bus_master), GFP_KERNEL);
> +
> + if (!mdev)
> + return -ENOMEM;
> +
> + mdev->clk = clk_get(&pdev->dev, "owire_clk");
> + if (!mdev->clk) {
> + err = -ENODEV;
> + goto failed_clk;
> + }
> +
> + mdev->bus_master = (struct w1_bus_master *)(mdev + 1);
> + mdev->clkdiv = (clk_get_rate(mdev->clk) / 1000000) - 1;
> +
> + res = request_mem_region(res->start, resource_size(res),
> + "mxc_w1");
> + if (!res) {
> + err = -EBUSY;
> + goto failed_req;
> + }
> +
> + mdev->regs = ioremap(res->start, resource_size(res));
> + if (!mdev->regs) {
> + printk(KERN_ERR"Cannot map frame buffer registers\n");
> + goto failed_ioremap;
> + }
> +
> + clk_enable(mdev->clk);
> + __raw_writeb(mdev->clkdiv, mdev->regs + MXC_W1_TIME_DIVIDER);
> +
> + mdev->bus_master->data = mdev;
> + mdev->bus_master->reset_bus = &mxc_w1_ds2_reset_bus;
> + mdev->bus_master->touch_bit = &mxc_w1_ds2_touch_bit;
> +
> + err = w1_add_master_device(mdev->bus_master);
> +
> + if (err)
> + goto failed_add;
> +
> + platform_set_drvdata(pdev, mdev);
> + return 0;
> +
> +failed_add:
> + iounmap(mdev->regs);
> +failed_ioremap:
> + release_mem_region(res->start, resource_size(res));
> +failed_req:
> + clk_put(mdev->clk);
> +failed_clk:
> + kfree(mdev);
> + return err;
> +}
> +
> +/*
> + * disassociate the w1 device from the driver
> + */
> +static int mxc_w1_remove(struct platform_device *pdev)
> +{
> + struct mxc_w1_device *mdev = platform_get_drvdata(pdev);
> + struct resource *res;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +
> + w1_remove_master_device(mdev->bus_master);
> +
> + iounmap(mdev->regs);
> + release_mem_region(res->start, resource_size(res));
> + clk_disable(mdev->clk);
> + clk_put(mdev->clk);
> +
> + platform_set_drvdata(pdev, NULL);
> +
> + return 0;
> +}
> +
> +static struct platform_driver mxc_w1_driver = {
> + .driver = {
> + .name = "mxc_w1",
> + },
> + .probe = mxc_w1_probe,
> + .remove = mxc_w1_remove,
> +};
> +
> +static int __init mxc_w1_init(void)
> +{
> + return platform_driver_register(&mxc_w1_driver);
> +}
> +
> +static void mxc_w1_exit(void)
> +{
> + platform_driver_unregister(&mxc_w1_driver);
> +}
> +
> +module_init(mxc_w1_init);
> +module_exit(mxc_w1_exit);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_AUTHOR("Freescale Semiconductors Inc");
> +MODULE_DESCRIPTION("Driver for One-Wire on MXC");
> --
> 1.5.2.5
>
>
--
Pengutronix - Linux Solutions for Science and Industry
Handelsregister: Amtsgericht Hildesheim, HRA 2686
Hannoversche Str. 2, 31134 Hildesheim, Germany
Phone: +49-5121-206917-0 | Fax: +49-5121-206917-9
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists