| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20100129160327.21495.57917.sendpatchset@localhost>
Date: Fri, 29 Jan 2010 17:03:27 +0100
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
To: linux-ide@...r.kernel.org
Cc: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>,
linux-kernel@...r.kernel.org
Subject: [PATCH 03/68] libata: move ATA timings code to ata-timings.c
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
Subject: [PATCH] libata: move ATA timings code to ata-timings.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
---
drivers/ata/Makefile | 2
drivers/ata/ata-timings.c | 179 ++++++++++++++++++++++++++++++++++++++++++++++
drivers/ata/libata-core.c | 173 --------------------------------------------
3 files changed, 180 insertions(+), 174 deletions(-)
Index: b/drivers/ata/Makefile
===================================================================
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -83,7 +83,7 @@ obj-$(CONFIG_ATA_GENERIC) += ata_generic
# Should be last libata driver
obj-$(CONFIG_PATA_LEGACY) += pata_legacy.o
-libata-objs := libata-core.o libata-scsi.o libata-eh.o
+libata-objs := ata-timings.o libata-core.o libata-scsi.o libata-eh.o
libata-$(CONFIG_ATA_SFF) += libata-sff.o
libata-$(CONFIG_SATA_PMP) += libata-pmp.o
libata-$(CONFIG_ATA_ACPI) += libata-acpi.o
Index: b/drivers/ata/ata-timings.c
===================================================================
--- /dev/null
+++ b/drivers/ata/ata-timings.c
@@ -0,0 +1,179 @@
+/*
+ * This mode timing computation functionality is ported over from
+ * drivers/ide/ide-timing.h and was originally written by Vojtech Pavlik
+ */
+
+#include <linux/kernel.h>
+#include <linux/libata.h>
+
+/*
+ * PIO 0-4, MWDMA 0-2 and UDMA 0-6 timings (in nanoseconds).
+ * These were taken from ATA/ATAPI-6 standard, rev 0a, except
+ * for UDMA6, which is currently supported only by Maxtor drives.
+ *
+ * For PIO 5/6 MWDMA 3/4 see the CFA specification 3.0.
+ */
+
+static const struct ata_timing ata_timing[] = {
+/* { XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 0, 960, 0 }, */
+ { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 0, 600, 0 },
+ { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 0, 383, 0 },
+ { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 0, 240, 0 },
+ { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 0, 180, 0 },
+ { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 0, 120, 0 },
+ { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 0, 100, 0 },
+ { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 0, 80, 0 },
+
+ { XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 50, 960, 0 },
+ { XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 30, 480, 0 },
+ { XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 20, 240, 0 },
+
+ { XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 20, 480, 0 },
+ { XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 5, 150, 0 },
+ { XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 5, 120, 0 },
+ { XFER_MW_DMA_3, 25, 0, 0, 0, 65, 25, 5, 100, 0 },
+ { XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 5, 80, 0 },
+
+/* { XFER_UDMA_SLOW, 0, 0, 0, 0, 0, 0, 0, 0, 150 }, */
+ { XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 0, 120 },
+ { XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 0, 80 },
+ { XFER_UDMA_2, 0, 0, 0, 0, 0, 0, 0, 0, 60 },
+ { XFER_UDMA_3, 0, 0, 0, 0, 0, 0, 0, 0, 45 },
+ { XFER_UDMA_4, 0, 0, 0, 0, 0, 0, 0, 0, 30 },
+ { XFER_UDMA_5, 0, 0, 0, 0, 0, 0, 0, 0, 20 },
+ { XFER_UDMA_6, 0, 0, 0, 0, 0, 0, 0, 0, 15 },
+
+ { 0xFF }
+};
+
+#define ENOUGH(v, unit) (((v) - 1) / (unit) + 1)
+#define EZ(v, unit) ((v) ? ENOUGH(v, unit) : 0)
+
+static void ata_timing_quantize(const struct ata_timing *t,
+ struct ata_timing *q, int T, int UT)
+{
+ q->setup = EZ(t->setup * 1000, T);
+ q->act8b = EZ(t->act8b * 1000, T);
+ q->rec8b = EZ(t->rec8b * 1000, T);
+ q->cyc8b = EZ(t->cyc8b * 1000, T);
+ q->active = EZ(t->active * 1000, T);
+ q->recover = EZ(t->recover * 1000, T);
+ q->dmack_hold = EZ(t->dmack_hold * 1000, T);
+ q->cycle = EZ(t->cycle * 1000, T);
+ q->udma = EZ(t->udma * 1000, UT);
+}
+
+void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
+ struct ata_timing *m, unsigned int what)
+{
+ if (what & ATA_TIMING_SETUP)
+ m->setup = max(a->setup, b->setup);
+ if (what & ATA_TIMING_ACT8B)
+ m->act8b = max(a->act8b, b->act8b);
+ if (what & ATA_TIMING_REC8B)
+ m->rec8b = max(a->rec8b, b->rec8b);
+ if (what & ATA_TIMING_CYC8B)
+ m->cyc8b = max(a->cyc8b, b->cyc8b);
+ if (what & ATA_TIMING_ACTIVE)
+ m->active = max(a->active, b->active);
+ if (what & ATA_TIMING_RECOVER)
+ m->recover = max(a->recover, b->recover);
+ if (what & ATA_TIMING_DMACK_HOLD)
+ m->dmack_hold = max(a->dmack_hold, b->dmack_hold);
+ if (what & ATA_TIMING_CYCLE)
+ m->cycle = max(a->cycle, b->cycle);
+ if (what & ATA_TIMING_UDMA)
+ m->udma = max(a->udma, b->udma);
+}
+EXPORT_SYMBOL_GPL(ata_timing_merge);
+
+const struct ata_timing *ata_timing_find_mode(u8 xfer_mode)
+{
+ const struct ata_timing *t = ata_timing;
+
+ while (xfer_mode > t->mode)
+ t++;
+
+ if (xfer_mode == t->mode)
+ return t;
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(ata_timing_find_mode);
+
+int ata_timing_compute(struct ata_device *adev, unsigned short speed,
+ struct ata_timing *t, int T, int UT)
+{
+ const u16 *id = adev->id;
+ const struct ata_timing *s;
+ struct ata_timing p;
+
+ /*
+ * Find the mode.
+ */
+
+ s = ata_timing_find_mode(speed);
+ if (!s)
+ return -EINVAL;
+
+ memcpy(t, s, sizeof(*s));
+
+ /*
+ * If the drive is an EIDE drive, it can tell us it needs extended
+ * PIO/MW_DMA cycle timing.
+ */
+
+ if (id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
+ memset(&p, 0, sizeof(p));
+
+ if (speed >= XFER_PIO_0 && speed < XFER_SW_DMA_0) {
+ if (speed <= XFER_PIO_2)
+ p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
+ else if ((speed <= XFER_PIO_4) ||
+ (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
+ p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
+ } else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+ p.cycle = id[ATA_ID_EIDE_DMA_MIN];
+
+ ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
+ }
+
+ /*
+ * Convert the timing to bus clock counts.
+ */
+
+ ata_timing_quantize(t, t, T, UT);
+
+ /*
+ * Even in DMA/UDMA modes we still use PIO access for IDENTIFY,
+ * S.M.A.R.T and some other commands. We have to ensure that the
+ * DMA cycle timing is slower/equal than the fastest PIO timing.
+ */
+
+ if (speed > XFER_PIO_6) {
+ ata_timing_compute(adev, adev->pio_mode, &p, T, UT);
+ ata_timing_merge(&p, t, t, ATA_TIMING_ALL);
+ }
+
+ /*
+ * Lengthen active & recovery time so that cycle time is correct.
+ */
+
+ if (t->act8b + t->rec8b < t->cyc8b) {
+ t->act8b += (t->cyc8b - (t->act8b + t->rec8b)) / 2;
+ t->rec8b = t->cyc8b - t->act8b;
+ }
+
+ if (t->active + t->recover < t->cycle) {
+ t->active += (t->cycle - (t->active + t->recover)) / 2;
+ t->recover = t->cycle - t->active;
+ }
+
+ /* In a few cases quantisation may produce enough errors to
+ leave t->cycle too low for the sum of active and recovery
+ if so we must correct this */
+ if (t->active + t->recover > t->cycle)
+ t->cycle = t->active + t->recover;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_timing_compute);
Index: b/drivers/ata/libata-core.c
===================================================================
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3032,179 +3032,6 @@ int sata_set_spd(struct ata_link *link)
return 1;
}
-/*
- * This mode timing computation functionality is ported over from
- * drivers/ide/ide-timing.h and was originally written by Vojtech Pavlik
- */
-/*
- * PIO 0-4, MWDMA 0-2 and UDMA 0-6 timings (in nanoseconds).
- * These were taken from ATA/ATAPI-6 standard, rev 0a, except
- * for UDMA6, which is currently supported only by Maxtor drives.
- *
- * For PIO 5/6 MWDMA 3/4 see the CFA specification 3.0.
- */
-
-static const struct ata_timing ata_timing[] = {
-/* { XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 0, 960, 0 }, */
- { XFER_PIO_0, 70, 290, 240, 600, 165, 150, 0, 600, 0 },
- { XFER_PIO_1, 50, 290, 93, 383, 125, 100, 0, 383, 0 },
- { XFER_PIO_2, 30, 290, 40, 330, 100, 90, 0, 240, 0 },
- { XFER_PIO_3, 30, 80, 70, 180, 80, 70, 0, 180, 0 },
- { XFER_PIO_4, 25, 70, 25, 120, 70, 25, 0, 120, 0 },
- { XFER_PIO_5, 15, 65, 25, 100, 65, 25, 0, 100, 0 },
- { XFER_PIO_6, 10, 55, 20, 80, 55, 20, 0, 80, 0 },
-
- { XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 50, 960, 0 },
- { XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 30, 480, 0 },
- { XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 20, 240, 0 },
-
- { XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 20, 480, 0 },
- { XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 5, 150, 0 },
- { XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 5, 120, 0 },
- { XFER_MW_DMA_3, 25, 0, 0, 0, 65, 25, 5, 100, 0 },
- { XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 5, 80, 0 },
-
-/* { XFER_UDMA_SLOW, 0, 0, 0, 0, 0, 0, 0, 0, 150 }, */
- { XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 0, 120 },
- { XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 0, 80 },
- { XFER_UDMA_2, 0, 0, 0, 0, 0, 0, 0, 0, 60 },
- { XFER_UDMA_3, 0, 0, 0, 0, 0, 0, 0, 0, 45 },
- { XFER_UDMA_4, 0, 0, 0, 0, 0, 0, 0, 0, 30 },
- { XFER_UDMA_5, 0, 0, 0, 0, 0, 0, 0, 0, 20 },
- { XFER_UDMA_6, 0, 0, 0, 0, 0, 0, 0, 0, 15 },
-
- { 0xFF }
-};
-
-#define ENOUGH(v, unit) (((v) - 1) / (unit) + 1)
-#define EZ(v, unit) ((v) ? ENOUGH(v, unit) : 0)
-
-static void ata_timing_quantize(const struct ata_timing *t,
- struct ata_timing *q, int T, int UT)
-{
- q->setup = EZ(t->setup * 1000, T);
- q->act8b = EZ(t->act8b * 1000, T);
- q->rec8b = EZ(t->rec8b * 1000, T);
- q->cyc8b = EZ(t->cyc8b * 1000, T);
- q->active = EZ(t->active * 1000, T);
- q->recover = EZ(t->recover * 1000, T);
- q->dmack_hold = EZ(t->dmack_hold * 1000, T);
- q->cycle = EZ(t->cycle * 1000, T);
- q->udma = EZ(t->udma * 1000, UT);
-}
-
-void ata_timing_merge(const struct ata_timing *a, const struct ata_timing *b,
- struct ata_timing *m, unsigned int what)
-{
- if (what & ATA_TIMING_SETUP)
- m->setup = max(a->setup, b->setup);
- if (what & ATA_TIMING_ACT8B)
- m->act8b = max(a->act8b, b->act8b);
- if (what & ATA_TIMING_REC8B)
- m->rec8b = max(a->rec8b, b->rec8b);
- if (what & ATA_TIMING_CYC8B)
- m->cyc8b = max(a->cyc8b, b->cyc8b);
- if (what & ATA_TIMING_ACTIVE)
- m->active = max(a->active, b->active);
- if (what & ATA_TIMING_RECOVER)
- m->recover = max(a->recover, b->recover);
- if (what & ATA_TIMING_DMACK_HOLD)
- m->dmack_hold = max(a->dmack_hold, b->dmack_hold);
- if (what & ATA_TIMING_CYCLE)
- m->cycle = max(a->cycle, b->cycle);
- if (what & ATA_TIMING_UDMA)
- m->udma = max(a->udma, b->udma);
-}
-
-const struct ata_timing *ata_timing_find_mode(u8 xfer_mode)
-{
- const struct ata_timing *t = ata_timing;
-
- while (xfer_mode > t->mode)
- t++;
-
- if (xfer_mode == t->mode)
- return t;
- return NULL;
-}
-
-int ata_timing_compute(struct ata_device *adev, unsigned short speed,
- struct ata_timing *t, int T, int UT)
-{
- const u16 *id = adev->id;
- const struct ata_timing *s;
- struct ata_timing p;
-
- /*
- * Find the mode.
- */
-
- s = ata_timing_find_mode(speed);
- if (!s)
- return -EINVAL;
-
- memcpy(t, s, sizeof(*s));
-
- /*
- * If the drive is an EIDE drive, it can tell us it needs extended
- * PIO/MW_DMA cycle timing.
- */
-
- if (id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
- memset(&p, 0, sizeof(p));
-
- if (speed >= XFER_PIO_0 && speed < XFER_SW_DMA_0) {
- if (speed <= XFER_PIO_2)
- p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
- else if ((speed <= XFER_PIO_4) ||
- (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
- p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
- } else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
- p.cycle = id[ATA_ID_EIDE_DMA_MIN];
-
- ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
- }
-
- /*
- * Convert the timing to bus clock counts.
- */
-
- ata_timing_quantize(t, t, T, UT);
-
- /*
- * Even in DMA/UDMA modes we still use PIO access for IDENTIFY,
- * S.M.A.R.T and some other commands. We have to ensure that the
- * DMA cycle timing is slower/equal than the fastest PIO timing.
- */
-
- if (speed > XFER_PIO_6) {
- ata_timing_compute(adev, adev->pio_mode, &p, T, UT);
- ata_timing_merge(&p, t, t, ATA_TIMING_ALL);
- }
-
- /*
- * Lengthen active & recovery time so that cycle time is correct.
- */
-
- if (t->act8b + t->rec8b < t->cyc8b) {
- t->act8b += (t->cyc8b - (t->act8b + t->rec8b)) / 2;
- t->rec8b = t->cyc8b - t->act8b;
- }
-
- if (t->active + t->recover < t->cycle) {
- t->active += (t->cycle - (t->active + t->recover)) / 2;
- t->recover = t->cycle - t->active;
- }
-
- /* In a few cases quantisation may produce enough errors to
- leave t->cycle too low for the sum of active and recovery
- if so we must correct this */
- if (t->active + t->recover > t->cycle)
- t->cycle = t->active + t->recover;
-
- return 0;
-}
-
/**
* ata_timing_cycle2mode - find xfer mode for the specified cycle duration
* @xfer_shift: ATA_SHIFT_* value for transfer type to examine.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists