| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1298037329-13683-1-git-send-email-anoop.pa@gmail.com>
Date: Fri, 18 Feb 2011 19:25:29 +0530
From: "Anoop P.A" <anoop.pa@...il.com>
To: ralf@...ux-mips.org, linux-mips@...ux-mips.org,
linux-kernel@...r.kernel.org
Cc: Anoop P A <anoop.pa@...il.com>
Subject: [PATCH] Make msp7120_reset generic
From: Anoop P A <anoop.pa@...il.com>
Remove platform dependency code from msp7120 reset code and make it generic.
Now the code can be reused for other boards running msp71xx family SoC.
Signed-off-by: Anoop P A <anoop.pa@...il.com>
---
arch/mips/pmc-sierra/msp71xx/msp_setup.c | 85 ++++++++++++++++++------------
1 files changed, 52 insertions(+), 33 deletions(-)
diff --git a/arch/mips/pmc-sierra/msp71xx/msp_setup.c b/arch/mips/pmc-sierra/msp71xx/msp_setup.c
index fb37a10..4a6cc0d 100644
--- a/arch/mips/pmc-sierra/msp71xx/msp_setup.c
+++ b/arch/mips/pmc-sierra/msp71xx/msp_setup.c
@@ -18,30 +18,33 @@
#include <msp_prom.h>
#include <msp_regs.h>
+#include <msp_gpio_macros.h>
#if defined(CONFIG_PMC_MSP7120_GW)
-#include <msp_regops.h>
+ /* GPIO 9 is the 4th GPIO of register 3
+ */
#define MSP_BOARD_RESET_GPIO 9
+#else
+#undef MSP_BOARD_RESET_GPIO
#endif
extern void msp_serial_setup(void);
extern void pmctwiled_setup(void);
-#if defined(CONFIG_PMC_MSP7120_EVAL) || \
- defined(CONFIG_PMC_MSP7120_GW) || \
- defined(CONFIG_PMC_MSP7120_FPGA)
/*
- * Performs the reset for MSP7120-based boards
+ * Performs the reset for MSP71xx-based boards
*/
-void msp7120_reset(void)
+void msp71xx_reset(void)
{
void *start, *end, *iptr;
register int i;
+ register u32 temp __maybe_unused;
/* Diasble all interrupts */
local_irq_disable();
#ifdef CONFIG_SYS_SUPPORTS_MULTITHREADING
dvpe();
+ dmt();
#endif
/* Cache the reset code of this function */
@@ -78,49 +81,56 @@ void msp7120_reset(void)
/* Wait a bit for the DDRC to settle */
for (i = 0; i < 100000000; i++);
-#if defined(CONFIG_PMC_MSP7120_GW)
+#if defined MSP_BOARD_RESET_GPIO
/*
- * Set GPIO 9 HI, (tied to board reset logic)
- * GPIO 9 is the 4th GPIO of register 3
+ * Set reset GPIO HI, (tied to board reset logic)
*
* NOTE: We cannot use the higher-level msp_gpio_mode()/out()
* as GPIO char driver may not be enabled and it would look up
* data inRAM!
*/
- set_value_reg32(GPIO_CFG3_REG, 0xf000, 0x8000);
- set_reg32(GPIO_DATA3_REG, 8);
+ temp = __raw_readl(MSP_GPIO_MODE_REGISTER[MSP_BOARD_RESET_GPIO]) &
+ ~BASIC_MODE_MASK(MSP_BOARD_RESET_GPIO);
+ __raw_writel(temp | BASIC_MODE(MSP_GPIO_OUTPUT, MSP_BOARD_RESET_GPIO),
+ MSP_GPIO_MODE_REGISTER[MSP_BOARD_RESET_GPIO]);
+ /* Now set the reset gpio pin hi */
+ temp = __raw_readl(MSP_GPIO_DATA_REGISTER[MSP_BOARD_RESET_GPIO]);
+ __raw_writel(temp | BASIC_DATA_MASK(MSP_BOARD_RESET_GPIO),
+ MSP_GPIO_DATA_REGISTER[MSP_BOARD_RESET_GPIO]);
/*
- * In case GPIO9 doesn't reset the board (jumper configurable!)
+ * In case GPIO doesn't reset the board (jumper configurable!)
* fallback to device reset below.
*/
#endif
- /* Set bit 1 of the MSP7120 reset register */
- *RST_SET_REG = 0x00000001;
+ /* Set bit 1 of the MSP71xx reset register */
+ __raw_writel(0x00000001, RST_SET_REG);
__asm__ __volatile__ (
- "endpoint: \n"
+ "endpoint:\n"
);
}
-#endif
void msp_restart(char *command)
{
- printk(KERN_WARNING "Now rebooting .......\n");
-
-#if defined(CONFIG_PMC_MSP7120_EVAL) || \
- defined(CONFIG_PMC_MSP7120_GW) || \
- defined(CONFIG_PMC_MSP7120_FPGA)
- msp7120_reset();
-#else
- /* No chip-specific reset code, just jump to the ROM reset vector */
- set_c0_status(ST0_BEV | ST0_ERL);
- change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
- flush_cache_all();
- write_c0_wired(0);
- __asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
-#endif
+ unsigned long family = identify_family();
+ switch (family) {
+ case FAMILY_MSP7100:
+ msp71xx_reset();
+ break;
+ default:
+ /* No chip-specific reset code, just jump
+ * to the ROM reset vector
+ */
+ set_c0_status(ST0_BEV | ST0_ERL);
+ change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
+ flush_cache_all();
+ write_c0_wired(0);
+
+ __asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
+ break;
+ }
}
void msp_halt(void)
@@ -141,9 +151,7 @@ void msp_power_off(void)
void __init plat_mem_setup(void)
{
- _machine_restart = msp_restart;
- _machine_halt = msp_halt;
- pm_power_off = msp_power_off;
+/*TODO: Move mem setup here */
}
extern struct plat_smp_ops msp_smtc_smp_ops;
@@ -244,3 +252,14 @@ void __init prom_init(void)
pmctwiled_setup();
#endif
}
+
+static int __init mips_reboot_setup(void)
+{
+ _machine_restart = msp_restart;
+ _machine_halt = msp_halt;
+ pm_power_off = msp_power_off;
+
+ return 0;
+}
+
+arch_initcall(mips_reboot_setup);
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists