| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1307692832-15643-1-git-send-email-linus.walleij@stericsson.com>
Date: Fri, 10 Jun 2011 10:00:32 +0200
From: Linus Walleij <linus.walleij@...ricsson.com>
To: Richard Purdie <rpurdie@...ys.net>, <linux-kernel@...r.kernel.org>
Cc: Lee Jones <lee.jones@...aro.org>,
Shreshtha Kumar Sahu <shreshthakumar.sahu@...ricsson.com>,
Linus Walleij <linus.walleij@...aro.org>
Subject: [PATCH 2/2] mach-ux500: add lm3530 ALS platform data for U5500
From: Shreshtha Kumar Sahu <shreshthakumar.sahu@...ricsson.com>
platform data for simple backlight driver for LM3530
in the u5500 platform
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@...ricsson.com>
Signed-off-by: Linus Walleij <linus.walleij@...aro.org>
---
arch/arm/mach-ux500/board-u5500.c | 84 ++++++++++++++++++++++++++++++++++++-
1 files changed, 83 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-ux500/board-u5500.c b/arch/arm/mach-ux500/board-u5500.c
index 44fd3b5..e58f0f5 100644
--- a/arch/arm/mach-ux500/board-u5500.c
+++ b/arch/arm/mach-ux500/board-u5500.c
@@ -10,16 +10,97 @@
#include <linux/amba/bus.h>
#include <linux/gpio.h>
#include <linux/irq.h>
+#include <linux/i2c.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
+#include <plat/pincfg.h>
+#include <plat/i2c.h>
+
#include <mach/hardware.h>
#include <mach/devices.h>
#include <mach/setup.h>
+#include "pins-db5500.h"
#include "devices-db5500.h"
+#include <linux/led-lm3530.h>
+
+/*
+ * GPIO
+ */
+
+static pin_cfg_t u5500_pins[] = {
+ /* I2C */
+ GPIO218_I2C2_SCL | PIN_INPUT_PULLUP,
+ GPIO219_I2C2_SDA | PIN_INPUT_PULLUP,
+
+ /* DISPLAY_ENABLE */
+ GPIO226_GPIO | PIN_OUTPUT_LOW,
+
+ /* Backlight Enbale */
+ GPIO224_GPIO | PIN_OUTPUT_HIGH,
+};
+/*
+ * I2C
+ */
+
+#define U5500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, _sm) \
+static struct nmk_i2c_controller u5500_i2c##id##_data = { \
+ /* \
+ * slave data setup time, which is \
+ * 250 ns,100ns,10ns which is 14,6,2 \
+ * respectively for a 48 Mhz \
+ * i2c clock \
+ */ \
+ .slsu = _slsu, \
+ /* Tx FIFO threshold */ \
+ .tft = _tft, \
+ /* Rx FIFO threshold */ \
+ .rft = _rft, \
+ /* std. mode operation */ \
+ .clk_freq = clk, \
+ .sm = _sm, \
+}
+/*
+ * The board uses TODO <3> i2c controllers, initialize all of
+ * them with slave data setup time of 250 ns,
+ * Tx & Rx FIFO threshold values as 1 and standard
+ * mode of operation
+ */
+
+U5500_I2C_CONTROLLER(2, 0xe, 1, 1, 400000, I2C_FREQ_MODE_FAST);
+
+static struct lm3530_platform_data u5500_als_platform_data = {
+ .mode = LM3530_BL_MODE_MANUAL,
+ .als_input_mode = LM3530_INPUT_ALS1,
+ .max_current = LM3530_FS_CURR_26mA,
+ .pwm_pol_hi = true,
+ .als_avrg_time = LM3530_ALS_AVRG_TIME_512ms,
+ .brt_ramp_law = 1, /* Linear */
+ .brt_ramp_fall = LM3530_RAMP_TIME_8s,
+ .brt_ramp_rise = LM3530_RAMP_TIME_8s,
+ .als1_resistor_sel = LM3530_ALS_IMPD_13_53kOhm,
+ .als2_resistor_sel = LM3530_ALS_IMPD_Z,
+ .als_vmin = 730, /* mV */
+ .als_vmax = 1020, /* mV */
+ .brt_val = 0x7F, /* Max brightness */
+};
+
+static struct i2c_board_info __initdata u5500_i2c2_devices[] = {
+ {
+ /* Backlight */
+ I2C_BOARD_INFO("lm3530-led", 0x36),
+ .platform_data = &u5500_als_platform_data,
+ },
+};
+
+static void __init u5500_i2c_init(void)
+{
+ db5500_add_i2c2(&u5500_i2c2_data);
+ i2c_register_board_info(2, ARRAY_AND_SIZE(u5500_i2c2_devices));
+}
static void __init u5500_uart_init(void)
{
db5500_add_uart0(NULL);
@@ -30,7 +111,8 @@ static void __init u5500_uart_init(void)
static void __init u5500_init_machine(void)
{
u5500_init_devices();
-
+ nmk_config_pins(u5500_pins, ARRAY_SIZE(u5500_pins));
+ u5500_i2c_init();
u5500_sdi_init();
u5500_uart_init();
}
--
1.7.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists