Message-ID: <1353288509-26703-1-git-send-email-ldewangan@nvidia.com>
Date:	Mon, 19 Nov 2012 06:58:29 +0530
From:	Laxman Dewangan <ldewangan@...dia.com>
To:	<broonie@...nsource.wolfsonmicro.com>, <lrg@...com>
CC:	<linux-kernel@...r.kernel.org>, <g.liakhovetski@....de>,
	Laxman Dewangan <ldewangan@...dia.com>
Subject: [PATCH] regulator: max8973: add regulator driver support

The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.

Add regulator driver for this device.

Signed-off-by: Laxman Dewangan <ldewangan@...dia.com>
---
 drivers/regulator/Kconfig                   |   10 +
 drivers/regulator/Makefile                  |    1 +
 drivers/regulator/max8973-regulator.c       |  505 +++++++++++++++++++++++++++
 include/linux/regulator/max8973-regulator.h |   72 ++++
 4 files changed, 588 insertions(+), 0 deletions(-)
 create mode 100644 drivers/regulator/max8973-regulator.c
 create mode 100644 include/linux/regulator/max8973-regulator.h

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index cbc685d..ddd8869 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -204,6 +204,16 @@ config REGULATOR_MAX8952
 	  via I2C bus. Maxim 8952 has one voltage output and supports 4 DVS
 	  modes ranging from 0.77V to 1.40V by 0.01V steps.
 
+config REGULATOR_MAX8973
+	tristate "Maxim MAX8973 voltage regulator "
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  The MAXIM MAX8973 high-efficiency. three phase, DC-DC step-down
+	  switching regulator delievers up to 9A of output current. Each
+	  phase operates at a 2MHz fixed frequency with a 120 deg shift
+	  from the adjacent phase, allowing the use of small magnetic component.
+
 config REGULATOR_MAX8997
 	tristate "Maxim 8997/8966 regulator"
 	depends on MFD_MAX8997
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index db274dc..ac093f3 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
 obj-$(CONFIG_REGULATOR_MAX8907) += max8907-regulator.o
 obj-$(CONFIG_REGULATOR_MAX8925) += max8925-regulator.o
 obj-$(CONFIG_REGULATOR_MAX8952) += max8952.o
+obj-$(CONFIG_REGULATOR_MAX8973) += max8973-regulator.o
 obj-$(CONFIG_REGULATOR_MAX8997) += max8997.o
 obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
 obj-$(CONFIG_REGULATOR_MAX77686) += max77686.o
diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c
new file mode 100644
index 0000000..e6328f9
--- /dev/null
+++ b/drivers/regulator/max8973-regulator.c
@@ -0,0 +1,505 @@
+/*
+ * max8973-regulator.c -- Maxim max8973
+ *
+ * Regulator driver for MAXIM 8973 DC-DC step-down switching regulator.
+ *
+ * Copyright (c) 2012, NVIDIA Corporation.
+ *
+ * Author: Laxman Dewangan <ldewangan@...dia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
+ * whether express or implied; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
+ * 02111-1307, USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/max8973-regulator.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/regmap.h>
+
+/* Register definitions */
+#define MAX8973_VOUT					0x0
+#define MAX8973_VOUT_DVS				0x1
+#define MAX8973_CONTROL1				0x2
+#define MAX8973_CONTROL2				0x3
+#define MAX8973_CHIPID1					0x4
+#define MAX8973_CHIPID2					0x5
+
+#define MAX8973_MAX_VOUT_REG				2
+
+/* MAX8973_VOUT */
+#define MAX8973_VOUT_ENABLE				BIT(7)
+#define MAX8973_VOUT_MASK				0x7F
+
+/* MAX8973_VOUT_DVS */
+#define MAX8973_DVS_VOUT_MASK				0x7F
+
+/* MAX8973_CONTROL1 */
+#define MAX8973_SNS_ENABLE				BIT(7)
+#define MAX8973_FPWM_EN_M				BIT(6)
+#define MAX8973_NFSR_ENABLE				BIT(5)
+#define MAX8973_AD_ENABLE				BIT(4)
+#define MAX8973_BIAS_ENABLE				BIT(3)
+#define MAX8973_FREQSHIFT_9PER				BIT(2)
+
+#define MAX8973_RAMP_12mV_PER_US			0x0
+#define MAX8973_RAMP_25mV_PER_US			0x1
+#define MAX8973_RAMP_50mV_PER_US			0x2
+#define MAX8973_RAMP_200mV_PER_US			0x3
+
+/* MAX8973_CONTROL2 */
+#define MAX8973_WDTMR_ENABLE				BIT(6)
+#define MAX8973_DISCH_ENBABLE				BIT(5)
+#define MAX8973_FT_ENABLE				BIT(4)
+
+#define MAX8973_CKKADV_TRIP_DISABLE			0xC
+#define MAX8973_CKKADV_TRIP_75mV_PER_US			0x0
+#define MAX8973_CKKADV_TRIP_150mV_PER_US		0x4
+#define MAX8973_CKKADV_TRIP_75mV_PER_US_HIST_DIS	0x8
+#define MAX8973_CONTROL_CLKADV_TRIP_MASK		0x00030000
+
+#define MAX8973_INDUCTOR_MIN_30_PER			0x0
+#define MAX8973_INDUCTOR_NOMINAL			0x1
+#define MAX8973_INDUCTOR_PLUS_30_PER			0x2
+#define MAX8973_INDUCTOR_PLUS_60_PER			0x3
+#define MAX8973_CONTROL_INDUCTOR_VALUE_MASK		0x00300000
+
+#define MAX8973_MIN_VOLATGE				606250
+#define MAX8973_MAX_VOLATGE				1400000
+#define MAX8973_VOLATGE_STEP				6250
+#define MAX8973_BUCK_N_VOLTAGE				0x80
+
+/* Maxim 8973 chip information */
+struct max8973_chip {
+	struct device *dev;
+	struct regulator_desc desc;
+	struct regulator_dev *rdev;
+	struct regmap *regmap;
+	bool enable_external_control;
+	int dvs_gpio;
+	int lru_index[MAX8973_MAX_VOUT_REG];
+	int curr_vout_val[MAX8973_MAX_VOUT_REG];
+	int curr_vout_reg;
+	int curr_gpio_val;
+	bool valid_dvs_gpio;
+};
+
+/*
+ * find_voltage_set_register: Find new voltage configuration register (VOUT).
+ * The finding of the new VOUT register will be based on the LRU mechanism.
+ * Each VOUT register will have different voltage configured . This
+ * Function will look if any of the VOUT register have requested voltage set
+ * or not.
+ *     - If it is already there then it will make that register as most
+ *       recently used and return as found so that caller need not to set
+ *       the VOUT register but need to set the proper gpios to select this
+ *       VOUT register.
+ *     - If requested voltage is not found then it will use the least
+ *       recently mechanism to get new VOUT register for new configuration
+ *       and will return not_found so that caller need to set new VOUT
+ *       register and then gpios (both).
+ */
+static bool find_voltage_set_register(struct max8973_chip *tps,
+		int req_vsel, int *vout_reg, int *gpio_val)
+{
+	int i;
+	bool found = false;
+	int new_vout_reg = tps->lru_index[MAX8973_MAX_VOUT_REG - 1];
+	int found_index = MAX8973_MAX_VOUT_REG - 1;
+
+	for (i = 0; i < MAX8973_MAX_VOUT_REG; ++i) {
+		if (tps->curr_vout_val[tps->lru_index[i]] == req_vsel) {
+			new_vout_reg = tps->lru_index[i];
+			found_index = i;
+			found = true;
+			goto update_lru_index;
+		}
+	}
+
+update_lru_index:
+	for (i = found_index; i > 0; i--)
+		tps->lru_index[i] = tps->lru_index[i - 1];
+
+	tps->lru_index[0] = new_vout_reg;
+	*gpio_val = new_vout_reg;
+	*vout_reg = MAX8973_VOUT + new_vout_reg;
+	return found;
+}
+
+static int max8973_dcdc_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct max8973_chip *max = rdev_get_drvdata(rdev);
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(max->regmap, max->curr_vout_reg, &data);
+	if (ret < 0) {
+		dev_err(max->dev, "register %d read failed, err = %d\n",
+			max->curr_vout_reg, ret);
+		return ret;
+	}
+	return data & MAX8973_VOUT_MASK;
+}
+
+static int max8973_dcdc_set_voltage_sel(struct regulator_dev *rdev,
+	     unsigned vsel)
+{
+	struct max8973_chip *max = rdev_get_drvdata(rdev);
+	int ret;
+	bool found = false;
+	int vout_reg = max->curr_vout_reg;
+	int gpio_val = max->curr_gpio_val;
+
+	/*
+	 * If gpios are available to select the VOUT register then least
+	 * recently used register for new configuration.
+	 */
+	if (max->valid_dvs_gpio)
+		found = find_voltage_set_register(max, vsel,
+					&vout_reg, &gpio_val);
+
+	if (!found) {
+		ret = regmap_update_bits(max->regmap, vout_reg,
+					MAX8973_VOUT_MASK, vsel);
+		if (ret < 0) {
+			dev_err(max->dev, "register %d update failed, err %d\n",
+				 vout_reg, ret);
+			return ret;
+		}
+		max->curr_vout_reg = vout_reg;
+		max->curr_vout_val[gpio_val] = vsel;
+	}
+
+	/* Select proper VOUT register vio gpios */
+	if (max->valid_dvs_gpio) {
+		gpio_set_value_cansleep(max->dvs_gpio, gpio_val & 0x1);
+		max->curr_gpio_val = gpio_val;
+	}
+	return 0;
+}
+
+static int max8973_dcdc_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct max8973_chip *max = rdev_get_drvdata(rdev);
+	int ret;
+	int pwm;
+
+	/* Enable force PWM mode in FAST mode only. */
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		pwm = MAX8973_FPWM_EN_M;
+		break;
+
+	case REGULATOR_MODE_NORMAL:
+		pwm = 0;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	ret = regmap_update_bits(max->regmap, MAX8973_CONTROL1,
+				MAX8973_FPWM_EN_M, pwm);
+	if (ret < 0)
+		dev_err(max->dev, "register %d update failed, err %d\n",
+				MAX8973_CONTROL1, ret);
+	return ret;
+}
+
+static unsigned int max8973_dcdc_get_mode(struct regulator_dev *rdev)
+{
+	struct max8973_chip *max = rdev_get_drvdata(rdev);
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(max->regmap, MAX8973_CONTROL1, &data);
+	if (ret < 0) {
+		dev_err(max->dev, "register %d read failed, err %d\n",
+				MAX8973_CONTROL1, ret);
+		return ret;
+	}
+	return (data & MAX8973_FPWM_EN_M) ?
+		REGULATOR_MODE_FAST : REGULATOR_MODE_NORMAL;
+}
+
+static struct regulator_ops max8973_dcdc_ops = {
+	.get_voltage_sel	= max8973_dcdc_get_voltage_sel,
+	.set_voltage_sel	= max8973_dcdc_set_voltage_sel,
+	.list_voltage		= regulator_list_voltage_linear,
+	.set_mode		= max8973_dcdc_set_mode,
+	.get_mode		= max8973_dcdc_get_mode,
+};
+
+static int __devinit max8973_init_dcdc(struct max8973_chip *max,
+		struct max8973_regulator_platform_data *pdata)
+{
+	int ret;
+	uint8_t	control1 = 0;
+	uint8_t control2 = 0;
+
+	if (pdata->control_flags & MAX8973_CONTROL_REMOTE_SENSE_ENABLE)
+		control1 |= MAX8973_SNS_ENABLE;
+
+	if (!(pdata->control_flags & MAX8973_CONTROL_FALLING_SLEW_RATE_ENABLE))
+		control1 |= MAX8973_NFSR_ENABLE;
+
+	if (pdata->control_flags & MAX8973_CONTROL_OUTPUT_ACTIVE_DISCH_ENABLE)
+		control1 |= MAX8973_AD_ENABLE;
+
+	if (pdata->control_flags & MAX8973_CONTROL_BIAS_ENABLE)
+		control1 |= MAX8973_BIAS_ENABLE;
+
+	if (pdata->control_flags & MAX8973_CONTROL_FREQ_SHIFT_9PER_ENABLE)
+		control1 |= MAX8973_FREQSHIFT_9PER;
+
+	/* Set ramp delay */
+	if (pdata->reg_init_data &&
+			pdata->reg_init_data->constraints.ramp_delay) {
+		if (pdata->reg_init_data->constraints.ramp_delay < 25000)
+			control1 = MAX8973_RAMP_12mV_PER_US;
+		else if (pdata->reg_init_data->constraints.ramp_delay < 50000)
+			control1 = MAX8973_RAMP_25mV_PER_US;
+		else if (pdata->reg_init_data->constraints.ramp_delay < 200000)
+			control1 = MAX8973_RAMP_50mV_PER_US;
+		else
+			control1 = MAX8973_RAMP_200mV_PER_US;
+	} else {
+		control1 = MAX8973_RAMP_12mV_PER_US;
+		max->desc.ramp_delay = 12500;
+	}
+
+	if (!(pdata->control_flags & MAX8973_CONTROL_PULL_DOWN_ENABLE))
+		control2 |= MAX8973_DISCH_ENBABLE;
+
+	/*  Clock advance trip configuration */
+	switch (pdata->control_flags & MAX8973_CONTROL_CLKADV_TRIP_MASK) {
+	case MAX8973_CONTROL_CLKADV_TRIP_DISABLED:
+		control2 |= MAX8973_CKKADV_TRIP_DISABLE;
+		break;
+
+	case MAX8973_CONTROL_CLKADV_TRIP_75mV_PER_US:
+		control2 |= MAX8973_CKKADV_TRIP_75mV_PER_US;
+		break;
+
+	case MAX8973_CONTROL_CLKADV_TRIP_150mV_PER_US:
+		control2 |= MAX8973_CKKADV_TRIP_150mV_PER_US;
+		break;
+
+	case MAX8973_CONTROL_CLKADV_TRIP_75mV_PER_US_HIST_DIS:
+		control2 |= MAX8973_CKKADV_TRIP_75mV_PER_US_HIST_DIS;
+		break;
+	}
+
+	/* Configure inductor value */
+	switch (pdata->control_flags & MAX8973_CONTROL_INDUCTOR_VALUE_MASK) {
+	case MAX8973_CONTROL_INDUCTOR_VALUE_NOMINAL:
+		control2 |= MAX8973_INDUCTOR_NOMINAL;
+		break;
+
+	case MAX8973_CONTROL_INDUCTOR_VALUE_MINUS_30_PER:
+		control2 |= MAX8973_INDUCTOR_MIN_30_PER;
+		break;
+
+	case MAX8973_CONTROL_INDUCTOR_VALUE_PLUS_30_PER:
+		control2 |= MAX8973_INDUCTOR_PLUS_30_PER;
+		break;
+
+	case MAX8973_CONTROL_INDUCTOR_VALUE_PLUS_60_PER:
+		control2 |= MAX8973_INDUCTOR_PLUS_60_PER;
+		break;
+	}
+
+	ret = regmap_write(max->regmap, MAX8973_CONTROL1, control1);
+	if (ret < 0) {
+		dev_err(max->dev, "register %d write failed, err = %d",
+				MAX8973_CONTROL1, ret);
+		return ret;
+	}
+
+	ret = regmap_write(max->regmap, MAX8973_CONTROL2, control2);
+	if (ret < 0) {
+		dev_err(max->dev, "register %d write failed, err = %d",
+				MAX8973_CONTROL2, ret);
+		return ret;
+	}
+
+	/* If external control is enabled then disable EN bit */
+	if (max->enable_external_control) {
+		ret = regmap_update_bits(max->regmap, MAX8973_VOUT,
+						MAX8973_VOUT_ENABLE, 0);
+		if (ret < 0)
+			dev_err(max->dev, "register %d update failed, err = %d",
+				MAX8973_VOUT, ret);
+	}
+	return ret;
+}
+
+static const struct regmap_config max8973_regmap_config = {
+	.reg_bits		= 8,
+	.val_bits		= 8,
+	.max_register		= MAX8973_CHIPID2,
+	.cache_type		= REGCACHE_RBTREE,
+};
+
+static int __devinit max8973_probe(struct i2c_client *client,
+				     const struct i2c_device_id *id)
+{
+	struct max8973_regulator_platform_data *pdata;
+	struct regulator_config config = { };
+	struct regulator_dev *rdev;
+	struct max8973_chip *max;
+	int ret;
+
+	pdata = client->dev.platform_data;
+	if (!pdata) {
+		dev_err(&client->dev, "No Platform data");
+		return -EIO;
+	}
+
+	max = devm_kzalloc(&client->dev, sizeof(*max), GFP_KERNEL);
+	if (!max) {
+		dev_err(&client->dev, "Memory allocation for max failed\n");
+		return -ENOMEM;
+	}
+
+	max->regmap = devm_regmap_init_i2c(client, &max8973_regmap_config);
+	if (IS_ERR(max->regmap)) {
+		ret = PTR_ERR(max->regmap);
+		dev_err(&client->dev, "regmap init failed, err %d\n", ret);
+		return ret;
+	}
+
+	i2c_set_clientdata(client, max);
+	max->dev = &client->dev;
+	max->desc.name = id->name;
+	max->desc.id = 0;
+	max->desc.ops = &max8973_dcdc_ops;
+	max->desc.type = REGULATOR_VOLTAGE;
+	max->desc.owner = THIS_MODULE;
+	max->desc.min_uV = MAX8973_MIN_VOLATGE;
+	max->desc.uV_step = MAX8973_VOLATGE_STEP;
+	max->desc.n_voltages = MAX8973_BUCK_N_VOLTAGE;
+
+	if (pdata->enable_ext_control) {
+		max->desc.enable_reg = MAX8973_VOUT;
+		max->desc.enable_mask = MAX8973_VOUT_ENABLE;
+		max8973_dcdc_ops.enable = regulator_is_enabled_regmap;
+		max8973_dcdc_ops.disable = regulator_disable_regmap;
+		max8973_dcdc_ops.is_enabled = regulator_is_enabled_regmap;
+	}
+
+	max->enable_external_control = pdata->enable_ext_control;
+	max->dvs_gpio = pdata->dvs_gpio;
+	max->curr_gpio_val = pdata->dvs_def_state;
+	max->curr_vout_reg = MAX8973_VOUT + pdata->dvs_def_state;
+	max->lru_index[0] = max->curr_vout_reg;
+	max->valid_dvs_gpio = false;
+
+	if (gpio_is_valid(max->dvs_gpio)) {
+		int gpio_flags;
+		int i;
+
+		gpio_flags = (pdata->dvs_def_state) ?
+				GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
+		ret = devm_gpio_request_one(&client->dev, max->dvs_gpio,
+				gpio_flags, "max8973-dvs");
+		if (ret) {
+			dev_err(&client->dev,
+				"gpio_request for gpio %d failed, err = %d\n",
+				max->dvs_gpio, ret);
+			return ret;
+		}
+		max->valid_dvs_gpio = true;
+
+		/*
+		 * Initialize the lru index with vout_reg id
+		 * The index 0 will be most recently used and
+		 * set with the max->curr_vout_reg */
+		for (i = 0; i < MAX8973_MAX_VOUT_REG; ++i)
+			max->lru_index[i] = i;
+		max->lru_index[0] = max->curr_vout_reg;
+		max->lru_index[max->curr_vout_reg] = 0;
+	}
+
+	ret = max8973_init_dcdc(max, pdata);
+	if (ret < 0) {
+		dev_err(max->dev, "Max8973 Init failed, err = %d\n", ret);
+		return ret;
+	}
+
+	config.dev = &client->dev;
+	config.init_data = pdata->reg_init_data;
+	config.driver_data = max;
+	config.of_node = client->dev.of_node;
+	config.regmap = max->regmap;
+
+	/* Register the regulators */
+	rdev = regulator_register(&max->desc, &config);
+	if (IS_ERR(rdev)) {
+		ret = PTR_ERR(rdev);
+		dev_err(max->dev, "regulator register failed, err %d\n", ret);
+		return ret;
+	}
+
+	max->rdev = rdev;
+	return 0;
+}
+
+static int __devexit max8973_remove(struct i2c_client *client)
+{
+	struct max8973_chip *max = i2c_get_clientdata(client);
+
+	regulator_unregister(max->rdev);
+	return 0;
+}
+
+static const struct i2c_device_id max8973_id[] = {
+	{.name = "max8973",},
+	{},
+};
+
+MODULE_DEVICE_TABLE(i2c, max8973_id);
+
+static struct i2c_driver max8973_i2c_driver = {
+	.driver = {
+		.name = "max8973",
+		.owner = THIS_MODULE,
+	},
+	.probe = max8973_probe,
+	.remove = __devexit_p(max8973_remove),
+	.id_table = max8973_id,
+};
+
+static int __init max8973_init(void)
+{
+	return i2c_add_driver(&max8973_i2c_driver);
+}
+subsys_initcall(max8973_init);
+
+static void __exit max8973_cleanup(void)
+{
+	i2c_del_driver(&max8973_i2c_driver);
+}
+module_exit(max8973_cleanup);
+
+MODULE_AUTHOR("Laxman Dewangan <ldewangan@...dia.com>");
+MODULE_DESCRIPTION("MAX8973 voltage regulator driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/regulator/max8973-regulator.h b/include/linux/regulator/max8973-regulator.h
new file mode 100644
index 0000000..f8acc05
--- /dev/null
+++ b/include/linux/regulator/max8973-regulator.h
@@ -0,0 +1,72 @@
+/*
+ * max8973-regulator.h -- MAXIM 8973 regulator
+ *
+ * Interface for regulator driver for MAXIM 8973 DC-DC step-down
+ * switching regulator.
+ *
+ * Copyright (C) 2012 NVIDIA Corporation
+
+ * Author: Laxman Dewangan <ldewangan@...dia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA	02110-1301, USA.
+ *
+ */
+
+#ifndef __LINUX_REGULATOR_MAX8973_H
+#define __LINUX_REGULATOR_MAX8973_H
+
+/*
+ * Control flags for configuration of the device.
+ * Client need to pass this information with ORed
+ */
+#define MAX8973_CONTROL_REMOTE_SENSE_ENABLE			0x00000001
+#define MAX8973_CONTROL_FALLING_SLEW_RATE_ENABLE		0x00000002
+#define MAX8973_CONTROL_OUTPUT_ACTIVE_DISCH_ENABLE		0x00000004
+#define MAX8973_CONTROL_BIAS_ENABLE				0x00000008
+#define MAX8973_CONTROL_PULL_DOWN_ENABLE			0x00000010
+#define MAX8973_CONTROL_FREQ_SHIFT_9PER_ENABLE			0x00000020
+
+#define MAX8973_CONTROL_CLKADV_TRIP_DISABLED			0x00000000
+#define MAX8973_CONTROL_CLKADV_TRIP_75mV_PER_US			0x00010000
+#define MAX8973_CONTROL_CLKADV_TRIP_150mV_PER_US		0x00020000
+#define MAX8973_CONTROL_CLKADV_TRIP_75mV_PER_US_HIST_DIS	0x00030000
+
+#define MAX8973_CONTROL_INDUCTOR_VALUE_NOMINAL			0x00000000
+#define MAX8973_CONTROL_INDUCTOR_VALUE_MINUS_30_PER		0x00100000
+#define MAX8973_CONTROL_INDUCTOR_VALUE_PLUS_30_PER		0x00200000
+#define MAX8973_CONTROL_INDUCTOR_VALUE_PLUS_60_PER		0x00300000
+
+/*
+ * struct max8973_regulator_platform_data - max8973 regulator platform data.
+ *
+ * @reg_init_data: The regulator init data.
+ * @control_flags: Control flags which are ORed value of above flags to
+ *		configure device.
+ * @enable_ext_control: Enable the voltage enable/disable through external
+ *		control signal from EN input pin. If it is false then
+ *		voltage output will be enabled/disabled through EN bit of
+ *		device register.
+ * @dvs_gpio: GPIO for dvs. It should be -1 if this is tied with fixed logic.
+ * @dvs_def_state: Default state of dvs. 1 if it is high else 0.
+ */
+struct max8973_regulator_platform_data {
+	struct regulator_init_data *reg_init_data;
+	unsigned long control_flags;
+	bool enable_ext_control;
+	int dvs_gpio;
+	unsigned dvs_def_state:1;
+};
+
+#endif /* __LINUX_REGULATOR_MAX8973_H */
-- 
1.7.1.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists