| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CADGdYn52fxgmq-ESz25fwHURonP0vCB4_5XOBq=i=Dn3sFe9pA@mail.gmail.com>
Date: Fri, 10 May 2013 07:47:57 +0530
From: amit daniel kachhap <amit.daniel@...sung.com>
To: Eduardo Valentin <eduardo.valentin@...com>
Cc: linux-pm@...r.kernel.org, Zhang Rui <rui.zhang@...el.com>,
linux-samsung-soc@...r.kernel.org, linux-kernel@...r.kernel.org,
Kukjin Kim <kgene.kim@...sung.com>
Subject: Re: [PATCH V3 09/21] thermal: exynos: Move register definitions from
driver file to data file
Hi Eduardo,
On Thu, May 9, 2013 at 8:02 PM, Eduardo Valentin
<eduardo.valentin@...com> wrote:
> Hey Amit,
>
> On 07-05-2013 09:00, Amit Daniel Kachhap wrote:
>> This patch migrates the TMU register definition/bitfields to data file. This
>> is needed to support SoC's which use the same TMU controller but register
>> validity, offsets or bitfield may slightly vary across SOC's.
>>
>> Acked-by: Kukjin Kim <kgene.kim@...sung.com>
>> Signed-off-by: Amit Daniel Kachhap <amit.daniel@...sung.com>
>> ---
>> drivers/thermal/samsung/exynos_tmu.c | 177 +++++++++-------------------
>> drivers/thermal/samsung/exynos_tmu.h | 76 ++++++++++++
>> drivers/thermal/samsung/exynos_tmu_data.c | 59 ++++++++++
>> drivers/thermal/samsung/exynos_tmu_data.h | 68 +++++++++++
>> 4 files changed, 260 insertions(+), 120 deletions(-)
>>
>> diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
>> index 23baeeb..97b87aa 100644
>> --- a/drivers/thermal/samsung/exynos_tmu.c
>> +++ b/drivers/thermal/samsung/exynos_tmu.c
>> @@ -36,77 +36,6 @@
>> #include "exynos_tmu.h"
>> #include "exynos_tmu_data.h"
>>
>> -/* Exynos generic registers */
>> -#define EXYNOS_TMU_REG_TRIMINFO 0x0
>> -#define EXYNOS_TMU_REG_CONTROL 0x20
>> -#define EXYNOS_TMU_REG_STATUS 0x28
>> -#define EXYNOS_TMU_REG_CURRENT_TEMP 0x40
>> -#define EXYNOS_TMU_REG_INTEN 0x70
>> -#define EXYNOS_TMU_REG_INTSTAT 0x74
>> -#define EXYNOS_TMU_REG_INTCLEAR 0x78
>> -
>> -#define EXYNOS_TMU_TRIM_TEMP_MASK 0xff
>> -#define EXYNOS_TMU_GAIN_SHIFT 8
>> -#define EXYNOS_TMU_GAIN_MASK 0xf
>> -#define EXYNOS_TMU_REF_VOLTAGE_SHIFT 24
>> -#define EXYNOS_TMU_REF_VOLTAGE_MASK 0x1f
>> -#define EXYNOS_TMU_BUF_SLOPE_SEL_MASK 0xf
>> -#define EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT 8
>> -#define EXYNOS_TMU_CORE_EN_SHIFT 0
>> -
>> -/* Exynos4210 specific registers */
>> -#define EXYNOS4210_TMU_REG_THRESHOLD_TEMP 0x44
>> -#define EXYNOS4210_TMU_REG_TRIG_LEVEL0 0x50
>> -#define EXYNOS4210_TMU_REG_TRIG_LEVEL1 0x54
>> -#define EXYNOS4210_TMU_REG_TRIG_LEVEL2 0x58
>> -#define EXYNOS4210_TMU_REG_TRIG_LEVEL3 0x5C
>> -#define EXYNOS4210_TMU_REG_PAST_TEMP0 0x60
>> -#define EXYNOS4210_TMU_REG_PAST_TEMP1 0x64
>> -#define EXYNOS4210_TMU_REG_PAST_TEMP2 0x68
>> -#define EXYNOS4210_TMU_REG_PAST_TEMP3 0x6C
>> -
>> -#define EXYNOS4210_TMU_TRIG_LEVEL0_MASK 0x1
>> -#define EXYNOS4210_TMU_TRIG_LEVEL1_MASK 0x10
>> -#define EXYNOS4210_TMU_TRIG_LEVEL2_MASK 0x100
>> -#define EXYNOS4210_TMU_TRIG_LEVEL3_MASK 0x1000
>> -#define EXYNOS4210_TMU_TRIG_LEVEL_MASK 0x1111
>> -#define EXYNOS4210_TMU_INTCLEAR_VAL 0x1111
>> -
>> -/* Exynos5250 and Exynos4412 specific registers */
>> -#define EXYNOS_TMU_TRIMINFO_CON 0x14
>> -#define EXYNOS_THD_TEMP_RISE 0x50
>> -#define EXYNOS_THD_TEMP_FALL 0x54
>> -#define EXYNOS_EMUL_CON 0x80
>> -
>> -#define EXYNOS_TRIMINFO_RELOAD 0x1
>> -#define EXYNOS_TRIMINFO_SHIFT 0x0
>> -#define EXYNOS_TMU_RISE_INT_MASK 0x111
>> -#define EXYNOS_TMU_RISE_INT_SHIFT 0
>> -#define EXYNOS_TMU_FALL_INT_MASK 0x111
>> -#define EXYNOS_TMU_FALL_INT_SHIFT 12
>> -#define EXYNOS_TMU_CLEAR_RISE_INT 0x111
>> -#define EXYNOS_TMU_CLEAR_FALL_INT (0x111 << 12)
>> -#define EXYNOS_TMU_TRIP_MODE_SHIFT 13
>> -#define EXYNOS_TMU_TRIP_MODE_MASK 0x7
>> -#define EXYNOS_TMU_THERM_TRIP_EN_SHIFT 12
>> -
>> -#define EXYNOS_TMU_INTEN_RISE0_SHIFT 0
>> -#define EXYNOS_TMU_INTEN_RISE1_SHIFT 4
>> -#define EXYNOS_TMU_INTEN_RISE2_SHIFT 8
>> -#define EXYNOS_TMU_INTEN_RISE3_SHIFT 12
>> -#define EXYNOS_TMU_INTEN_FALL0_SHIFT 16
>> -#define EXYNOS_TMU_INTEN_FALL1_SHIFT 20
>> -#define EXYNOS_TMU_INTEN_FALL2_SHIFT 24
>> -
>> -#ifdef CONFIG_THERMAL_EMULATION
>> -#define EXYNOS_EMUL_TIME 0x57F0
>> -#define EXYNOS_EMUL_TIME_MASK 0xffff
>> -#define EXYNOS_EMUL_TIME_SHIFT 16
>> -#define EXYNOS_EMUL_DATA_SHIFT 8
>> -#define EXYNOS_EMUL_DATA_MASK 0xFF
>> -#define EXYNOS_EMUL_ENABLE 0x1
>> -#endif /* CONFIG_THERMAL_EMULATION */
>> -
>> struct exynos_tmu_data {
>> struct exynos_tmu_platform_data *pdata;
>> struct resource *mem;
>> @@ -191,6 +120,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
>> {
>> struct exynos_tmu_data *data = platform_get_drvdata(pdev);
>> struct exynos_tmu_platform_data *pdata = data->pdata;
>> + struct exynos_tmu_registers *reg = pdata->registers;
>> unsigned int status, trim_info, con;
>> unsigned int rising_threshold = 0, falling_threshold = 0;
>> int ret = 0, threshold_code, i, trigger_levs = 0;
>> @@ -198,20 +128,20 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
>> mutex_lock(&data->lock);
>> clk_enable(data->clk);
>>
>> - status = readb(data->base + EXYNOS_TMU_REG_STATUS);
>> + status = readb(data->base + reg->tmu_status);
>> if (!status) {
>> ret = -EBUSY;
>> goto out;
>> }
>>
>> - if (data->soc == SOC_ARCH_EXYNOS) {
>> - __raw_writel(EXYNOS_TRIMINFO_RELOAD,
>> - data->base + EXYNOS_TMU_TRIMINFO_CON);
>> - }
>> + if (data->soc == SOC_ARCH_EXYNOS)
>> + __raw_writel(1, data->base + reg->triminfo_ctrl);
>> +
>> /* Save trimming info in order to perform calibration */
>> - trim_info = readl(data->base + EXYNOS_TMU_REG_TRIMINFO);
>> - data->temp_error1 = trim_info & EXYNOS_TMU_TRIM_TEMP_MASK;
>> - data->temp_error2 = ((trim_info >> 8) & EXYNOS_TMU_TRIM_TEMP_MASK);
>> + trim_info = readl(data->base + reg->triminfo_data);
>> + data->temp_error1 = trim_info & EXYNOS_TMU_TEMP_MASK;
>> + data->temp_error2 = ((trim_info >> reg->triminfo_85_shift) &
>> + EXYNOS_TMU_TEMP_MASK);
>
> You changed from EXYNOS_TMU_TRIM_TEMP_MASK to EXYNOS_TMU_TEMP_MASK. Was
> it this really what you wanted?
Actually temp masks are same so removed EXYNOS_TMU_TRIM_TEMP_MASK.
>
>>
>> if ((pdata->min_efuse_value > data->temp_error1) ||
>> (data->temp_error1 > pdata->max_efuse_value) ||
>> @@ -231,13 +161,12 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
>> goto out;
>> }
>> writeb(threshold_code,
>> - data->base + EXYNOS4210_TMU_REG_THRESHOLD_TEMP);
>> + data->base + reg->threshold_temp);
>> for (i = 0; i < trigger_levs; i++)
>> writeb(pdata->trigger_levels[i],
>> - data->base + EXYNOS4210_TMU_REG_TRIG_LEVEL0 + i * 4);
>> + data->base + reg->threshold_th0 + i * 4);
>>
>
> Is 4 your addressing unit? I believe there is a macro definition for this.
yes 4 is a addressing unit. This is only used for 1 SOC so didn't define macro.
>
>> - writel(EXYNOS4210_TMU_INTCLEAR_VAL,
>> - data->base + EXYNOS_TMU_REG_INTCLEAR);
>> + writel(reg->inten_rise_mask, data->base + reg->tmu_intclear);
>> } else if (data->soc == SOC_ARCH_EXYNOS) {
>> /* Write temperature code for rising and falling threshold */
>> for (i = 0; i < trigger_levs; i++) {
>> @@ -258,18 +187,19 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
>> }
>> if (pdata->trigger_type[i] != HW_TRIP)
>> continue;
>> - con = readl(data->base + EXYNOS_TMU_REG_CONTROL);
>> - con |= (1 << EXYNOS_TMU_THERM_TRIP_EN_SHIFT);
>> - writel(con, data->base + EXYNOS_TMU_REG_CONTROL);
>> + con = readl(data->base + reg->tmu_ctrl);
>> + con |= (1 << reg->therm_trip_en_shift);
>> + writel(con, data->base + reg->tmu_ctrl);
>> }
>>
>> writel(rising_threshold,
>> - data->base + EXYNOS_THD_TEMP_RISE);
>> + data->base + reg->threshold_th0);
>> writel(falling_threshold,
>> - data->base + EXYNOS_THD_TEMP_FALL);
>> + data->base + reg->threshold_th1);
>>
>> - writel(EXYNOS_TMU_CLEAR_RISE_INT | EXYNOS_TMU_CLEAR_FALL_INT,
>> - data->base + EXYNOS_TMU_REG_INTCLEAR);
>> + writel((reg->inten_rise_mask << reg->inten_rise_shift) |
>> + (reg->inten_fall_mask << reg->inten_fall_shift),
>> + data->base + reg->tmu_intclear);
>> }
>> out:
>> clk_disable(data->clk);
>> @@ -282,46 +212,46 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on)
>> {
>> struct exynos_tmu_data *data = platform_get_drvdata(pdev);
>> struct exynos_tmu_platform_data *pdata = data->pdata;
>> + struct exynos_tmu_registers *reg = pdata->registers;
>> unsigned int con, interrupt_en;
>>
>> mutex_lock(&data->lock);
>> clk_enable(data->clk);
>>
>> - con = readl(data->base + EXYNOS_TMU_REG_CONTROL);
>> + con = readl(data->base + reg->tmu_ctrl);
>>
>> if (pdata->reference_voltage) {
>> - con &= ~(EXYNOS_TMU_REF_VOLTAGE_MASK <<
>> - EXYNOS_TMU_REF_VOLTAGE_SHIFT);
>> - con |= pdata->reference_voltage << EXYNOS_TMU_REF_VOLTAGE_SHIFT;
>> + con &= ~(reg->buf_vref_sel_mask << reg->buf_vref_sel_shift);
>> + con |= pdata->reference_voltage << reg->buf_vref_sel_shift;
>> }
>>
>> if (pdata->gain) {
>> - con &= ~(EXYNOS_TMU_GAIN_MASK << EXYNOS_TMU_GAIN_SHIFT);
>> - con |= (pdata->gain << EXYNOS_TMU_GAIN_SHIFT);
>> + con &= ~(reg->buf_slope_sel_mask << reg->buf_slope_sel_shift);
>> + con |= (pdata->gain << reg->buf_slope_sel_shift);
>> }
>>
>> if (pdata->noise_cancel_mode) {
>> - con &= ~(EXYNOS_TMU_TRIP_MODE_MASK <<
>> - EXYNOS_TMU_TRIP_MODE_SHIFT);
>> - con |= (pdata->noise_cancel_mode << EXYNOS_TMU_TRIP_MODE_SHIFT);
>> + con &= ~(reg->therm_trip_mode_mask <<
>> + reg->therm_trip_mode_shift);
>> + con |= (pdata->noise_cancel_mode << reg->therm_trip_mode_shift);
>> }
>>
>> if (on) {
>> - con |= (1 << EXYNOS_TMU_CORE_EN_SHIFT);
>> + con |= (1 << reg->core_en_shift);
>> interrupt_en =
>> - pdata->trigger_enable[3] << EXYNOS_TMU_INTEN_RISE3_SHIFT |
>> - pdata->trigger_enable[2] << EXYNOS_TMU_INTEN_RISE2_SHIFT |
>> - pdata->trigger_enable[1] << EXYNOS_TMU_INTEN_RISE1_SHIFT |
>> - pdata->trigger_enable[0] << EXYNOS_TMU_INTEN_RISE0_SHIFT;
>> + pdata->trigger_enable[3] << reg->inten_rise3_shift |
>> + pdata->trigger_enable[2] << reg->inten_rise2_shift |
>> + pdata->trigger_enable[1] << reg->inten_rise1_shift |
>> + pdata->trigger_enable[0] << reg->inten_rise0_shift;
>> if (pdata->threshold_falling)
>> interrupt_en |=
>> - interrupt_en << EXYNOS_TMU_INTEN_FALL0_SHIFT;
>> + interrupt_en << reg->inten_fall0_shift;
>> } else {
>> - con &= ~(1 << EXYNOS_TMU_CORE_EN_SHIFT);
>> + con &= ~(1 << reg->core_en_shift);
>> interrupt_en = 0; /* Disable all interrupts */
>> }
>> - writel(interrupt_en, data->base + EXYNOS_TMU_REG_INTEN);
>> - writel(con, data->base + EXYNOS_TMU_REG_CONTROL);
>> + writel(interrupt_en, data->base + reg->tmu_inten);
>> + writel(con, data->base + reg->tmu_ctrl);
>>
>> clk_disable(data->clk);
>> mutex_unlock(&data->lock);
>> @@ -329,13 +259,15 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on)
>>
>> static int exynos_tmu_read(struct exynos_tmu_data *data)
>> {
>> + struct exynos_tmu_platform_data *pdata = data->pdata;
>> + struct exynos_tmu_registers *reg = pdata->registers;
>> u8 temp_code;
>> int temp;
>>
>> mutex_lock(&data->lock);
>> clk_enable(data->clk);
>>
>> - temp_code = readb(data->base + EXYNOS_TMU_REG_CURRENT_TEMP);
>> + temp_code = readb(data->base + reg->tmu_cur_temp);
>> temp = code_to_temp(data, temp_code);
>>
>> clk_disable(data->clk);
>> @@ -348,7 +280,9 @@ static int exynos_tmu_read(struct exynos_tmu_data *data)
>> static int exynos_tmu_set_emulation(void *drv_data, unsigned long temp)
>> {
>> struct exynos_tmu_data *data = drv_data;
>> - unsigned int reg;
>> + struct exynos_tmu_platform_data *pdata = data->pdata;
>> + struct exynos_tmu_registers *reg = pdata->registers;
>> + unsigned int val;
>> int ret = -EINVAL;
>>
>> if (data->soc == SOC_ARCH_EXYNOS4210)
>> @@ -360,19 +294,19 @@ static int exynos_tmu_set_emulation(void *drv_data, unsigned long temp)
>> mutex_lock(&data->lock);
>> clk_enable(data->clk);
>>
>> - reg = readl(data->base + EXYNOS_EMUL_CON);
>> + val = readl(data->base + reg->emul_con);
>>
>> if (temp) {
>> temp /= MCELSIUS;
>>
>> - reg = (EXYNOS_EMUL_TIME << EXYNOS_EMUL_TIME_SHIFT) |
>> + val = (EXYNOS_EMUL_TIME << reg->emul_time_shift) |
>> (temp_to_code(data, temp)
>> - << EXYNOS_EMUL_DATA_SHIFT) | EXYNOS_EMUL_ENABLE;
>> + << reg->emul_temp_shift) | EXYNOS_EMUL_ENABLE;
>> } else {
>> - reg &= ~EXYNOS_EMUL_ENABLE;
>> + val &= ~EXYNOS_EMUL_ENABLE;
>> }
>>
>> - writel(reg, data->base + EXYNOS_EMUL_CON);
>> + writel(val, data->base + reg->emul_con);
>>
>> clk_disable(data->clk);
>> mutex_unlock(&data->lock);
>> @@ -389,17 +323,20 @@ static void exynos_tmu_work(struct work_struct *work)
>> {
>> struct exynos_tmu_data *data = container_of(work,
>> struct exynos_tmu_data, irq_work);
>> + struct exynos_tmu_platform_data *pdata = data->pdata;
>> + struct exynos_tmu_registers *reg = pdata->registers;
>>
>> exynos_report_trigger();
>> mutex_lock(&data->lock);
>> clk_enable(data->clk);
>> +
>> if (data->soc == SOC_ARCH_EXYNOS)
>> - writel(EXYNOS_TMU_CLEAR_RISE_INT |
>> - EXYNOS_TMU_CLEAR_FALL_INT,
>> - data->base + EXYNOS_TMU_REG_INTCLEAR);
>> + writel((reg->inten_rise_mask << reg->inten_rise_shift) |
>> + (reg->inten_fall_mask << reg->inten_fall_shift),
>> + data->base + reg->tmu_intclear);
>> else
>> - writel(EXYNOS4210_TMU_INTCLEAR_VAL,
>> - data->base + EXYNOS_TMU_REG_INTCLEAR);
>> + writel(reg->inten_rise_mask, data->base + reg->tmu_intclear);
>> +
>> clk_disable(data->clk);
>> mutex_unlock(&data->lock);
>>
>> diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
>> index 70cc518..1e5e492 100644
>> --- a/drivers/thermal/samsung/exynos_tmu.h
>> +++ b/drivers/thermal/samsung/exynos_tmu.h
>> @@ -46,6 +46,81 @@ enum soc_type {
>> };
>>
>> /**
>> + * struct exynos_tmu_register - register descriptors to access registers and
>> + * bitfields. The register validity, offsets and bitfield values may vary
>> + * slightly across different exynos SOC's.
>
> No documentation for your registers? Or at least where to find explanation?
yes didn't write documentation. Will do it.
>
>> + */
>> +struct exynos_tmu_registers {
>> + u32 triminfo_data;
>> + u32 triminfo_25_shift;
>> + u32 triminfo_85_shift;
>> +
>> + u32 triminfo_ctrl;
>> + u32 triminfo_reload_shift;
>> +
>> + u32 tmu_ctrl;
>> + u32 buf_vref_sel_shift;
>> + u32 buf_vref_sel_mask;
>> + u32 therm_trip_mode_shift;
>> + u32 therm_trip_mode_mask;
>> + u32 therm_trip_en_shift;
>> + u32 buf_slope_sel_shift;
>> + u32 buf_slope_sel_mask;
>> + u32 therm_trip_tq_en_shift;
>> + u32 core_en_shift;
>> +
>> + u32 tmu_status;
>> +
>> + u32 tmu_cur_temp;
>> + u32 tmu_cur_temp_shift;
>> +
>> + u32 threshold_temp;
>> +
>> + u32 threshold_th0;
>> + u32 threshold_th0_l0_shift;
>> + u32 threshold_th0_l1_shift;
>> + u32 threshold_th0_l2_shift;
>> + u32 threshold_th0_l3_shift;
>> +
>> + u32 threshold_th1;
>> + u32 threshold_th1_l0_shift;
>> + u32 threshold_th1_l1_shift;
>> + u32 threshold_th1_l2_shift;
>> + u32 threshold_th1_l3_shift;
>> +
>> + u32 threshold_th2;
>> + u32 threshold_th2_l0_shift;
>> +
>> + u32 threshold_th3;
>> + u32 threshold_th3_l0_shift;
>> +
>> + u32 tmu_inten;
>> + u32 inten_rise_shift;
>> + u32 inten_rise_mask;
>> + u32 inten_fall_shift;
>> + u32 inten_fall_mask;
>> + u32 inten_rise0_shift;
>> + u32 inten_rise1_shift;
>> + u32 inten_rise2_shift;
>> + u32 inten_rise3_shift;
>> + u32 inten_fall0_shift;
>> + u32 inten_fall1_shift;
>> + u32 inten_fall2_shift;
>> + u32 inten_fall3_shift;
>> +
>> + u32 tmu_intstat;
>> +
>> + u32 tmu_intclear;
>> +
>> + u32 tmu_evten;
>> +
>> + u32 emul_con;
>> + u32 emul_temp_shift;
>> + u32 emul_time_shift;
>> + u32 emul_time_mask;
>> +};
>> +
>> +/**
>> * struct exynos_tmu_platform_data
>> * @threshold: basic temperature for generating interrupt
>> * 25 <= threshold <= 125 [unit: degree Celsius]
>> @@ -116,5 +191,6 @@ struct exynos_tmu_platform_data {
>> enum soc_type type;
>> struct freq_clip_table freq_tab[4];
>> unsigned int freq_tab_count;
>> + struct exynos_tmu_registers *registers;
>> };
>> #endif /* _LINUX_EXYNOS_THERMAL_H */
>> diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c
>> index 6b937f5..3a1ded1 100644
>> --- a/drivers/thermal/samsung/exynos_tmu_data.c
>> +++ b/drivers/thermal/samsung/exynos_tmu_data.c
>> @@ -25,6 +25,28 @@
>> #include "exynos_tmu_data.h"
>>
>> #if defined(CONFIG_CPU_EXYNOS4210)
>> +static struct exynos_tmu_registers exynos4210_tmu_registers = {
>> + .triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
>> + .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
>> + .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
>> + .tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
>> + .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
>> + .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
>> + .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
>> + .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
>> + .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
>> + .tmu_status = EXYNOS_TMU_REG_STATUS,
>> + .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
>> + .threshold_temp = EXYNOS4210_TMU_REG_THRESHOLD_TEMP,
>> + .threshold_th0 = EXYNOS4210_TMU_REG_TRIG_LEVEL0,
>> + .tmu_inten = EXYNOS_TMU_REG_INTEN,
>> + .inten_rise_mask = EXYNOS4210_TMU_TRIG_LEVEL_MASK,
>> + .inten_rise0_shift = EXYNOS_TMU_INTEN_RISE0_SHIFT,
>> + .inten_rise1_shift = EXYNOS_TMU_INTEN_RISE1_SHIFT,
>> + .inten_rise2_shift = EXYNOS_TMU_INTEN_RISE2_SHIFT,
>> + .inten_rise3_shift = EXYNOS_TMU_INTEN_RISE3_SHIFT,
>> + .tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
>> +};
>> struct exynos_tmu_platform_data const exynos4210_default_tmu_data = {
>> .threshold = 80,
>> .trigger_levels[0] = 5,
>> @@ -55,10 +77,46 @@ struct exynos_tmu_platform_data const exynos4210_default_tmu_data = {
>> },
>> .freq_tab_count = 2,
>> .type = SOC_ARCH_EXYNOS4210,
>> + .registers = &exynos4210_tmu_registers,
>> };
>> #endif
>>
>> #if defined(CONFIG_SOC_EXYNOS5250) || defined(CONFIG_SOC_EXYNOS4412)
>> +static struct exynos_tmu_registers exynos5250_tmu_registers = {
>> + .triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
>> + .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
>> + .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
>> + .triminfo_ctrl = EXYNOS_TMU_TRIMINFO_CON,
>> + .triminfo_reload_shift = EXYNOS_TRIMINFO_RELOAD_SHIFT,
>> + .tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
>> + .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
>> + .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
>> + .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
>> + .therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
>> + .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
>> + .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
>> + .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
>> + .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
>> + .tmu_status = EXYNOS_TMU_REG_STATUS,
>> + .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
>> + .threshold_th0 = EXYNOS_THD_TEMP_RISE,
>> + .threshold_th1 = EXYNOS_THD_TEMP_FALL,
>> + .tmu_inten = EXYNOS_TMU_REG_INTEN,
>> + .inten_rise_mask = EXYNOS_TMU_RISE_INT_MASK,
>> + .inten_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT,
>> + .inten_fall_mask = EXYNOS_TMU_FALL_INT_MASK,
>> + .inten_fall_shift = EXYNOS_TMU_FALL_INT_SHIFT,
>> + .inten_rise0_shift = EXYNOS_TMU_INTEN_RISE0_SHIFT,
>> + .inten_rise1_shift = EXYNOS_TMU_INTEN_RISE1_SHIFT,
>> + .inten_rise2_shift = EXYNOS_TMU_INTEN_RISE2_SHIFT,
>> + .inten_rise3_shift = EXYNOS_TMU_INTEN_RISE3_SHIFT,
>> + .inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT,
>> + .tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
>> + .emul_con = EXYNOS_EMUL_CON,
>> + .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
>> + .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT,
>> + .emul_time_mask = EXYNOS_EMUL_TIME_MASK,
>> +};
>> struct exynos_tmu_platform_data const exynos5250_default_tmu_data = {
>> .threshold_falling = 10,
>> .trigger_levels[0] = 85,
>> @@ -93,5 +151,6 @@ struct exynos_tmu_platform_data const exynos5250_default_tmu_data = {
>> },
>> .freq_tab_count = 2,
>> .type = SOC_ARCH_EXYNOS,
>> + .registers = &exynos5250_tmu_registers,
>> };
>> #endif
>
> One thing, I believe your data can be declared as const.
yes they are already const.
Thanks,
Amit Daniel
>
>> diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h
>> index 5b69711..0560413 100644
>> --- a/drivers/thermal/samsung/exynos_tmu_data.h
>> +++ b/drivers/thermal/samsung/exynos_tmu_data.h
>> @@ -23,6 +23,74 @@
>> #ifndef _LINUX_EXYNOS_TMU_DATA_H
>> #define _LINUX_EXYNOS_TMU_DATA_H
>>
>> +/* Exynos generic registers */
>> +#define EXYNOS_TMU_REG_TRIMINFO 0x0
>> +#define EXYNOS_TMU_REG_CONTROL 0x20
>> +#define EXYNOS_TMU_REG_STATUS 0x28
>> +#define EXYNOS_TMU_REG_CURRENT_TEMP 0x40
>> +#define EXYNOS_TMU_REG_INTEN 0x70
>> +#define EXYNOS_TMU_REG_INTSTAT 0x74
>> +#define EXYNOS_TMU_REG_INTCLEAR 0x78
>> +
>> +#define EXYNOS_TMU_TEMP_MASK 0xff
>> +#define EXYNOS_TMU_REF_VOLTAGE_SHIFT 24
>> +#define EXYNOS_TMU_REF_VOLTAGE_MASK 0x1f
>> +#define EXYNOS_TMU_BUF_SLOPE_SEL_MASK 0xf
>> +#define EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT 8
>> +#define EXYNOS_TMU_CORE_EN_SHIFT 0
>> +
>> +/* Exynos4210 specific registers */
>> +#define EXYNOS4210_TMU_REG_THRESHOLD_TEMP 0x44
>> +#define EXYNOS4210_TMU_REG_TRIG_LEVEL0 0x50
>> +#define EXYNOS4210_TMU_REG_TRIG_LEVEL1 0x54
>> +#define EXYNOS4210_TMU_REG_TRIG_LEVEL2 0x58
>> +#define EXYNOS4210_TMU_REG_TRIG_LEVEL3 0x5C
>> +#define EXYNOS4210_TMU_REG_PAST_TEMP0 0x60
>> +#define EXYNOS4210_TMU_REG_PAST_TEMP1 0x64
>> +#define EXYNOS4210_TMU_REG_PAST_TEMP2 0x68
>> +#define EXYNOS4210_TMU_REG_PAST_TEMP3 0x6C
>> +
>> +#define EXYNOS4210_TMU_TRIG_LEVEL0_MASK 0x1
>> +#define EXYNOS4210_TMU_TRIG_LEVEL1_MASK 0x10
>> +#define EXYNOS4210_TMU_TRIG_LEVEL2_MASK 0x100
>> +#define EXYNOS4210_TMU_TRIG_LEVEL3_MASK 0x1000
>> +#define EXYNOS4210_TMU_TRIG_LEVEL_MASK 0x1111
>> +#define EXYNOS4210_TMU_INTCLEAR_VAL 0x1111
>> +
>> +/* Exynos5250 and Exynos4412 specific registers */
>> +#define EXYNOS_TMU_TRIMINFO_CON 0x14
>> +#define EXYNOS_THD_TEMP_RISE 0x50
>> +#define EXYNOS_THD_TEMP_FALL 0x54
>> +#define EXYNOS_EMUL_CON 0x80
>> +
>> +#define EXYNOS_TRIMINFO_RELOAD_SHIFT 1
>> +#define EXYNOS_TRIMINFO_25_SHIFT 0
>> +#define EXYNOS_TRIMINFO_85_SHIFT 8
>> +#define EXYNOS_TMU_RISE_INT_MASK 0x111
>> +#define EXYNOS_TMU_RISE_INT_SHIFT 0
>> +#define EXYNOS_TMU_FALL_INT_MASK 0x111
>> +#define EXYNOS_TMU_FALL_INT_SHIFT 12
>> +#define EXYNOS_TMU_CLEAR_RISE_INT 0x111
>> +#define EXYNOS_TMU_CLEAR_FALL_INT (0x111 << 12)
>> +#define EXYNOS_TMU_TRIP_MODE_SHIFT 13
>> +#define EXYNOS_TMU_TRIP_MODE_MASK 0x7
>> +#define EXYNOS_TMU_THERM_TRIP_EN_SHIFT 12
>> +
>> +#define EXYNOS_TMU_INTEN_RISE0_SHIFT 0
>> +#define EXYNOS_TMU_INTEN_RISE1_SHIFT 4
>> +#define EXYNOS_TMU_INTEN_RISE2_SHIFT 8
>> +#define EXYNOS_TMU_INTEN_RISE3_SHIFT 12
>> +#define EXYNOS_TMU_INTEN_FALL0_SHIFT 16
>> +#define EXYNOS_TMU_INTEN_FALL1_SHIFT 20
>> +#define EXYNOS_TMU_INTEN_FALL2_SHIFT 24
>> +
>> +#define EXYNOS_EMUL_TIME 0x57F0
>> +#define EXYNOS_EMUL_TIME_MASK 0xffff
>> +#define EXYNOS_EMUL_TIME_SHIFT 16
>> +#define EXYNOS_EMUL_DATA_SHIFT 8
>> +#define EXYNOS_EMUL_DATA_MASK 0xFF
>> +#define EXYNOS_EMUL_ENABLE 0x1
>> +
>> #if defined(CONFIG_CPU_EXYNOS4210) && defined(CONFIG_EXYNOS_THERMAL_DATA)
>> extern struct exynos_tmu_platform_data const exynos4210_default_tmu_data;
>> #define EXYNOS4210_TMU_DRV_DATA (&exynos4210_default_tmu_data)
>>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists