| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20130603141851.GG3370@gmail.com>
Date: Mon, 3 Jun 2013 15:18:51 +0100
From: Lee Jones <lee.jones@...aro.org>
To: J Keerthy <j-keerthy@...com>
Cc: linux-kernel@...r.kernel.org, linux-doc@...r.kernel.org,
devicetree-discuss@...ts.ozlabs.org, swarren@...dotorg.org,
broonie@...nsource.wolfsonmicro.com, rob.herring@...xeda.com,
rob@...dley.net, mturquette@...aro.org, sameo@...ux.intel.com,
wim@...ana.be, lgirdwood@...il.com, gg@...mlogic.co.uk,
t-kristo@...com, Ian Lartey <ian@...mlogic.co.uk>
Subject: Re: [PATCH] mfd: DT bindings for the palmas family MFD
On Mon, 03 Jun 2013, J Keerthy wrote:
> From: Graeme Gregory <gg@...mlogic.co.uk>
>
> Add the various binding files for the palmas family of chips. There is a
> top level MFD binding then a seperate binding for regulators IP blocks on chips.
>
> Signed-off-by: Graeme Gregory <gg@...mlogic.co.uk>
> Signed-off-by: J Keerthy <j-keerthy@...com>
> Signed-off-by: Ian Lartey <ian@...mlogic.co.uk>
> ---
> Documentation/devicetree/bindings/mfd/palmas.txt | 49 ++++++
> .../devicetree/bindings/regulator/palmas-pmic.txt | 165 ++++++++++++++++++++
> 2 files changed, 214 insertions(+), 0 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/mfd/palmas.txt
> create mode 100644 Documentation/devicetree/bindings/regulator/palmas-pmic.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/palmas.txt b/Documentation/devicetree/bindings/mfd/palmas.txt
> new file mode 100644
> index 0000000..c6c5e78
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/palmas.txt
> @@ -0,0 +1,49 @@
> +* palmas device tree bindings
> +
> +The TI palmas family current members :-
> +twl6035 (palmas)
> +twl6037 (palmas)
> +tps65913 (palmas)
> +tps65914 (palmas)
> +
> +Required properties:
> +- compatible : Should be from the list
> + ti,twl6035
> + ti,twl6036
> + ti,twl6037
> + ti,tps65913
> + ti,tps65914
> + ti,tps80036
> +and also the generic series names
> + ti,palmas
> +- interrupt-controller : palmas has its own internal IRQs
> +- #interrupt-cells : should be set to 2 for IRQ number and flags
> + The first cell is the IRQ number.
> + The second cell is the flags, encoded as the trigger masks from
> + Documentation/devicetree/bindings/interrupts.txt
> +- interrupt-parent : The parent interrupt controller.
> +
> +Optional properties:
> + ti,mux_padX : set the pad register X (1-2) to the correct muxing for the
> + hardware, if not set will use muxing in OTP.
> +
> +Example:
> +
> +palmas {
Should this be 'palmas@48 {', as it has an address?
> + compatible = "ti,twl6035", "ti,palmas";
> + reg = <0x48>
> + interrupt-parent = <&intc>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + ti,mux-pad1 = <0>;
> + ti,mux-pad2 = <0>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmic {
> + compatible = "ti,twl6035-pmic", "ti,palmas-pmic";
> + ....
> + };
> +}
> diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt
> new file mode 100644
> index 0000000..f7bbc3e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt
> @@ -0,0 +1,165 @@
> +* palmas regulator IP block devicetree bindings
> +
> +Required properties:
> +- compatible : Should be from the list
> + ti,twl6035-pmic
> + ti,twl6036-pmic
> + ti,twl6037-pmic
> + ti,tps65913-pmic
> + ti,tps65914-pmic
> +and also the generic series names
> + ti,palmas-pmic
> +
> +Optional properties:
> +- ti,ldo6-vibrator : ldo6 is in vibrator mode
> +
> +Optional nodes:
> +- regulators : should contain the constrains and init information for the
> + regulators. It should contain a subnode per regulator from the
> + list.
> + For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP,
> + smps45, smps457, smps7 depending on varient, smps6, smps[8-10],
> + ldo[1-9], ldoln, ldousb
> +
> + optional chip specific regulator fields :-
> + ti,warm-reset - maintain voltage during warm reset(boolean)
Pushing the boat out a bit here, but is it possible to reuse
'regulator-always-on' for this?
> + ti,roof-floor - control voltage selection by pin(boolean)
Is this the same as a GPIO regulator?
If so, you might not need to add superfluous vendor specific properties.
See: Documentation/devicetree/bindings/regulator/gpio-regulator.txt
> + ti,sleep-mode - mode to adopt in pmic sleep 0 - off, 1 - auto,
> + 2 - eco, 3 - forced pwm
I've seen lots of sleep-mode properties, can't we define a generic
one?
> + ti,tstep - slope control 0 - Jump, 1 10mV/us, 2 5mV/us, 3 2.5mV/us
> + ti,smps-range - OTP has the wrong range set for the hardware so override
> + 0 - low range, 1 - high range
> +
> +Example:
> +
> +pmic@0 {
May as well drop the '@0' here unless it's meaningful.
> + compatible = "ti,twl6035-pmic", "ti,palmas-pmic";
> + interrupt-parent = <&palmas>;
> + interrupts = <14 0>;
Use the defines found in:
arch/arm/boot/dts/include/dt-bindings/interrupt-controller/irq.h
> + interrupt-name = "short-irq";
> +
> + ti,ldo6_vibrator;
DT doesn't like '_'s, use a '-'s instead.
> + regulators {
> + smps12_reg : smps12 {
> + regulator-name = "smps12";
> + regulator-min-microvolt = < 600000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-always-on;
> + regulator-boot-on;
> + ti,warm-reset;
Hmm.. I see you're using 'regulator-always-on' and 'ti,warm-reset'
here. Is there every a case where there is one without the other?
> + ti,roof-floor;
> + ti,mode-sleep = <0>;
> + ti,tstep = <0>;
> + ti,smps-range = <1>;
> + };
> +
> + smps3_reg: smps3 {
> + regulator-name = "smps3";
> + regulator-min-microvolt = < 600000>;
> + regulator-max-microvolt = <1310000>;
> + };
Wow, this is a big example.
I don't think you need to provide more than 1 or 2 of these _reg nodes.
> + smps45_reg: smps45 {
> + regulator-name = "smps45";
> + regulator-min-microvolt = < 600000>;
> + regulator-max-microvolt = <1310000>;
> + };
> +
> + smps6_reg: smps6 {
> + regulator-name = "smps6";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + };
> +
> + smps7_reg: smps7 {
> + regulator-name = "smps7";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + smps8_reg: smps8 {
> + regulator-name = "smps8";
> + regulator-min-microvolt = < 600000>;
> + regulator-max-microvolt = <1310000>;
> + };
> +
> + smps9_reg: smps9 {
> + regulator-name = "smps9";
> + regulator-min-microvolt = <2100000>;
> + regulator-max-microvolt = <2100000>;
> + };
> +
> + smps10_reg: smps10 {
> + regulator-name = "smps10";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + ldo1_reg: ldo1 {
> + regulator-name = "ldo1";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + };
> +
> + ldo2_reg: ldo2 {
> + regulator-name = "ldo2";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + };
> +
> + ldo3_reg: ldo3 {
> + regulator-name = "ldo3";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + };
> +
> + ldo4_reg: ldo4 {
> + regulator-name = "ldo4";
> + regulator-min-microvolt = <2200000>;
> + regulator-max-microvolt = <2200000>;
> + };
> +
> + ldo5_reg: ldo5 {
> + regulator-name = "ldo5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + ldo6_reg: ldo6 {
> + regulator-name = "ldo6";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + };
> +
> + ldo7_reg: ldo7 {
> + regulator-name = "ldo7";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + };
> +
> + ldo8_reg: ldo8 {
> + regulator-name = "ldo8";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + };
> +
> + ldo9_reg: ldo9 {
> + regulator-name = "ldo9";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + ldoln_reg: ldoln {
> + regulator-name = "ldoln";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + ldousb_reg: ldousb {
> + regulator-name = "ldousb";
> + regulator-min-microvolt = <3250000>;
> + regulator-max-microvolt = <3250000>;
> + };
> + };
> +};
--
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists