| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1382706463-3892-3-git-send-email-maxime.ripard@free-electrons.com>
Date: Fri, 25 Oct 2013 14:07:40 +0100
From: Maxime Ripard <maxime.ripard@...e-electrons.com>
To: daniel.lezcano@...aro.org, tglx@...utronix.de
Cc: linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
sboyd@...eaurora.org, kevin.z.m.zh@...il.com,
sunny@...winnertech.com, shuge@...winnertech.com,
zhuzhenhua@...winnertech.com,
Gregory Clement <gregory.clement@...e-electrons.com>,
Maxime Ripard <maxime.ripard@...e-electrons.com>
Subject: [PATCH v2 2/5] clocksource: Add Allwinner SoCs HS timers driver
Most of the Allwinner SoCs (at this time, all but the A10) also have a
High Speed timers that are not using the 24MHz oscillator as a source
but rather the AHB clock running much faster.
The IP is slightly different between the A10s/A13 and the one used in
the A20/A31, since the latter have 4 timers available, while the former
have only 2 of them.
Signed-off-by: Maxime Ripard <maxime.ripard@...e-electrons.com>
Tested-by: Emilio López <emilio@...pez.com.ar>
---
.../bindings/timer/allwinner,sun5i-a13-hstimer.txt | 22 +++
arch/arm/mach-sunxi/Kconfig | 1 +
drivers/clocksource/Kconfig | 4 +
drivers/clocksource/Makefile | 1 +
drivers/clocksource/timer-sun5i.c | 192 +++++++++++++++++++++
5 files changed, 220 insertions(+)
create mode 100644 Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt
create mode 100644 drivers/clocksource/timer-sun5i.c
diff --git a/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt
new file mode 100644
index 0000000..7c26154
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt
@@ -0,0 +1,22 @@
+Allwinner SoCs High Speed Timer Controller
+
+Required properties:
+
+- compatible : should be "allwinner,sun5i-a13-hstimer" or
+ "allwinner,sun7i-a20-hstimer"
+- reg : Specifies base physical address and size of the registers.
+- interrupts : The interrupts of these timers (2 for the sun5i IP, 4 for the sun7i
+ one)
+- clocks: phandle to the source clock (usually the AHB clock)
+
+Example:
+
+timer@...60000 {
+ compatible = "allwinner,sun7i-a20-hstimer";
+ reg = <0x01c60000 0x1000>;
+ interrupts = <0 51 1>,
+ <0 52 1>,
+ <0 53 1>,
+ <0 54 1>;
+ clocks = <&ahb1_gates 19>;
+};
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index c9e72c8..bce0d42 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -12,3 +12,4 @@ config ARCH_SUNXI
select PINCTRL_SUNXI
select SPARSE_IRQ
select SUN4I_TIMER
+ select SUN5I_HSTIMER
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index bdb953e..884eeff 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -37,6 +37,10 @@ config SUN4I_TIMER
select CLKSRC_MMIO
bool
+config SUN5I_HSTIMER
+ select CLKSRC_MMIO
+ bool
+
config VT8500_TIMER
bool
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 33621ef..358358d 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_ARCH_MOXART) += moxart_timer.o
obj-$(CONFIG_ARCH_MXS) += mxs_timer.o
obj-$(CONFIG_ARCH_PRIMA2) += timer-prima2.o
obj-$(CONFIG_SUN4I_TIMER) += sun4i_timer.o
+obj-$(CONFIG_SUN5I_HSTIMER) += timer-sun5i.o
obj-$(CONFIG_ARCH_TEGRA) += tegra20_timer.o
obj-$(CONFIG_VT8500_TIMER) += vt8500_timer.o
obj-$(CONFIG_ARCH_NSPIRE) += zevio-timer.o
diff --git a/drivers/clocksource/timer-sun5i.c b/drivers/clocksource/timer-sun5i.c
new file mode 100644
index 0000000..bddc522
--- /dev/null
+++ b/drivers/clocksource/timer-sun5i.c
@@ -0,0 +1,192 @@
+/*
+ * Allwinner SoCs hstimer driver.
+ *
+ * Copyright (C) 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@...e-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqreturn.h>
+#include <linux/sched_clock.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+
+#define TIMER_IRQ_EN_REG 0x00
+#define TIMER_IRQ_EN(val) BIT(val)
+#define TIMER_IRQ_ST_REG 0x04
+#define TIMER_CTL_REG(val) (0x20 * (val) + 0x10)
+#define TIMER_CTL_ENABLE BIT(0)
+#define TIMER_CTL_RELOAD BIT(1)
+#define TIMER_CTL_CLK_PRES(val) (((val) & 0x7) << 4)
+#define TIMER_CTL_ONESHOT BIT(7)
+#define TIMER_INTVAL_LO_REG(val) (0x20 * (val) + 0x14)
+#define TIMER_INTVAL_HI_REG(val) (0x20 * (val) + 0x18)
+#define TIMER_CNTVAL_LO_REG(val) (0x20 * (val) + 0x1c)
+#define TIMER_CNTVAL_HI_REG(val) (0x20 * (val) + 0x20)
+
+#define TIMER_SYNC_TICKS 3
+
+static void __iomem *timer_base;
+static u32 ticks_per_jiffy;
+
+/*
+ * When we disable a timer, we need to wait at least for 2 cycles of
+ * the timer source clock. We will use for that the clocksource timer
+ * that is already setup and runs at the same frequency than the other
+ * timers, and we never will be disabled.
+ */
+static void sun5i_clkevt_sync(void)
+{
+ u32 old = readl(timer_base + TIMER_CNTVAL_LO_REG(1));
+
+ while ((old - readl(timer_base + TIMER_CNTVAL_LO_REG(1))) < TIMER_SYNC_TICKS)
+ cpu_relax();
+}
+
+static void sun5i_clkevt_time_stop(u8 timer)
+{
+ u32 val = readl(timer_base + TIMER_CTL_REG(timer));
+ writel(val & ~TIMER_CTL_ENABLE, timer_base + TIMER_CTL_REG(timer));
+
+ sun5i_clkevt_sync();
+}
+
+static void sun5i_clkevt_time_setup(u8 timer, u32 delay)
+{
+ writel(delay, timer_base + TIMER_INTVAL_LO_REG(timer));
+}
+
+static void sun5i_clkevt_time_start(u8 timer, bool periodic)
+{
+ u32 val = readl(timer_base + TIMER_CTL_REG(timer));
+
+ if (periodic)
+ val &= ~TIMER_CTL_ONESHOT;
+ else
+ val |= TIMER_CTL_ONESHOT;
+
+ writel(val | TIMER_CTL_ENABLE | TIMER_CTL_RELOAD,
+ timer_base + TIMER_CTL_REG(timer));
+}
+
+static void sun5i_clkevt_mode(enum clock_event_mode mode,
+ struct clock_event_device *clk)
+{
+ switch (mode) {
+ case CLOCK_EVT_MODE_PERIODIC:
+ sun5i_clkevt_time_stop(0);
+ sun5i_clkevt_time_setup(0, ticks_per_jiffy);
+ sun5i_clkevt_time_start(0, true);
+ break;
+ case CLOCK_EVT_MODE_ONESHOT:
+ sun5i_clkevt_time_stop(0);
+ sun5i_clkevt_time_start(0, false);
+ break;
+ case CLOCK_EVT_MODE_UNUSED:
+ case CLOCK_EVT_MODE_SHUTDOWN:
+ default:
+ sun5i_clkevt_time_stop(0);
+ break;
+ }
+}
+
+static int sun5i_clkevt_next_event(unsigned long evt,
+ struct clock_event_device *unused)
+{
+ sun5i_clkevt_time_stop(0);
+ sun5i_clkevt_time_setup(0, evt - TIMER_SYNC_TICKS);
+ sun5i_clkevt_time_start(0, false);
+
+ return 0;
+}
+
+static struct clock_event_device sun5i_clockevent = {
+ .name = "sun5i_tick",
+ .rating = 340,
+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .set_mode = sun5i_clkevt_mode,
+ .set_next_event = sun5i_clkevt_next_event,
+};
+
+
+static irqreturn_t sun5i_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = (struct clock_event_device *)dev_id;
+
+ writel(0x1, timer_base + TIMER_IRQ_ST_REG);
+ evt->event_handler(evt);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction sun5i_timer_irq = {
+ .name = "sun5i_timer0",
+ .flags = IRQF_TIMER | IRQF_IRQPOLL,
+ .handler = sun5i_timer_interrupt,
+ .dev_id = &sun5i_clockevent,
+};
+
+static u32 sun5i_timer_sched_read(void)
+{
+ return ~readl(timer_base + TIMER_CNTVAL_LO_REG(1));
+}
+
+static void __init sun5i_timer_init(struct device_node *node)
+{
+ unsigned long rate;
+ struct clk *clk;
+ int ret, irq;
+ u32 val;
+
+ timer_base = of_iomap(node, 0);
+ if (!timer_base)
+ panic("Can't map registers");
+
+ irq = irq_of_parse_and_map(node, 0);
+ if (irq <= 0)
+ panic("Can't parse IRQ");
+
+ clk = of_clk_get(node, 0);
+ if (IS_ERR(clk))
+ panic("Can't get timer clock");
+ clk_prepare_enable(clk);
+ rate = clk_get_rate(clk);
+
+ writel(~0, timer_base + TIMER_INTVAL_LO_REG(1));
+ writel(TIMER_CTL_ENABLE | TIMER_CTL_RELOAD,
+ timer_base + TIMER_CTL_REG(1));
+
+ setup_sched_clock(sun5i_timer_sched_read, 32, rate);
+ clocksource_mmio_init(timer_base + TIMER_CNTVAL_LO_REG(1), node->name,
+ rate, 340, 32, clocksource_mmio_readl_down);
+
+ ticks_per_jiffy = DIV_ROUND_UP(rate, HZ);
+
+ ret = setup_irq(irq, &sun5i_timer_irq);
+ if (ret)
+ pr_warn("failed to setup irq %d\n", irq);
+
+ /* Enable timer0 interrupt */
+ val = readl(timer_base + TIMER_IRQ_EN_REG);
+ writel(val | TIMER_IRQ_EN(0), timer_base + TIMER_IRQ_EN_REG);
+
+ sun5i_clockevent.cpumask = cpu_possible_mask;
+ sun5i_clockevent.irq = irq;
+
+ clockevents_config_and_register(&sun5i_clockevent, rate,
+ TIMER_SYNC_TICKS, 0xffffffff);
+}
+CLOCKSOURCE_OF_DECLARE(sun5i_a13, "allwinner,sun5i-a13-hstimer",
+ sun5i_timer_init);
+CLOCKSOURCE_OF_DECLARE(sun7i_a20, "allwinner,sun7i-a20-hstimer",
+ sun5i_timer_init);
--
1.8.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists