linux-kernel - Re: [PATCH] mtd: nand: stm_nand

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20140703100522.756f9715@bbrezillon>
Date:	Thu, 3 Jul 2014 10:05:22 +0200
From:	Boris BREZILLON <boris.brezillon@...e-electrons.com>
To:	Brian Norris <computersforpeace@...il.com>
Cc:	Lee Jones <lee.jones@...aro.org>, devicetree@...r.kernel.org,
	Boris BREZILLON <b.brezillon.dev@...il.com>,
	kernel@...inux.com, linux-kernel@...r.kernel.org,
	linux-mtd@...ts.infradead.org, "Gupta, Pekon\"" <pekon@...com>,
	Ezequiel Garcia <ezequiel.garcia@...e-electrons.com>,
	linux-arm-kernel@...ts.infradead.org,
	Jason Gunthorpe <jgunthorpe@...idianresearch.com>
Subject: Re: [PATCH] mtd: nand: stm_nand_bch: add new driver

Hi Brian,

On Wed, 2 Jul 2014 17:22:37 -0700
Brian Norris <computersforpeace@...il.com> wrote:

> Hi Lee,
> 
> On Wed, May 28, 2014 at 10:20:05AM +0100, Lee Jones wrote:
> > This is a squashed version of the submission to avoid re-sending the
> > entire set over and over, essentially clogging up the MLs.
> 
> Thanks. I think I'd prefer to accept your driver in a form like this
> too. A few comments below.
> 
> And I'll get one big comment out of the way here: can you abstract your
> ST BBT code into its own self-contained portion, preferably in a
> separate source file, a la nand_bbt.c? Then, provide a way to optionally
> use either your ST BBT or the existing BBT -- perhaps a NAND_BBT_ST flag
> for chip->bbt_options, and a matching device tree property. That way,
> even though you require a legacy format for bootloader interoperability,
> someone can theoretically utilize more mainstream (albeit, not
> necessarily better...) BBT support from nand_bbt.c. I think this will
> provide the best balance between your existing product support and
> upstream-friendly modularity/flexibility. I'm open to other suggestions,
> of course.
> 
> > Cc: computersforpeace@...il.com
> > Cc: Gupta, Pekon" <pekon@...com>
> > Cc: Ezequiel Garcia <ezequiel.garcia@...e-electrons.com>
> > Cc: linux-mtd@...ts.infradead.org
> > Signed-off-by: Lee Jones <lee.jones@...aro.org>
> > ---
> 
> Please add versioning to your next patch(es), and describe changes here.
> 
> >  Documentation/devicetree/bindings/mtd/stm-nand.txt |   87 +
> 
> See:
> 
>   Documentation/devicetree/bindings/submitting-patches.txt
> 

[...]

> > +
> > +	nand_timing0: nand-timing {
> > +		sig-setup	= <10>;
> > +		sig-hold	= <10>;
> > +		CE-deassert	= <0>;
> > +		WE-to-RBn	= <100>;
> > +		wr-on		= <10>;
> > +		wr-off		= <30>;
> > +		rd-on		= <10>;
> > +		rd-off		= <30>;
> > +		chip-delay	= <30>;		/* delay in us */
> > +	};
> 
> You didn't document any of this node. And I don't think we want to
> specify every single timing parameter in DT; it may make sense to use
> Boris Brezillon's approach (I note this further down, in the driver
> code) for mapping non-ONFI NAND timings into a compatible ONFI timing
> mode. This will greatly simplify the bindings needed, since it's
> standardized and auto-detectable in many cases.


AFAIR, the NAND timing representation for non-ONFI chips question was
left unanswered:

https://lkml.org/lkml/2014/5/20/581

I can definitely respin my NAND timings series, but I'd like to be sure
this is how you want it done before doing so.

Just as a reminder, you and Jason thought NAND timings for non-ONFI
chips could be auto detected thanks to READID informations (by storing
some sort of "NANDID <-> timings" association table).

Best Regards,

Boris


-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/