| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20141020131412.GF7443@ldesroches-Latitude-E6320>
Date: Mon, 20 Oct 2014 15:14:12 +0200
From: Ludovic Desroches <ludovic.desroches@...el.com>
To: Wenyou Yang <wenyou.yang@...el.com>, <wsa@...-dreams.de>,
<linux-i2c@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<nicolas.ferre@...el.com>, <linux-arm-kernel@...ts.infradead.org>
CC: <khilman@...nel.org>
Subject: Re: [PATCH 1/3] i2c/at91: add support for runtime PM
Adding Kevin in the CC list since he had some comments about the PM
runtime support for the SPI driver.
On Mon, Oct 20, 2014 at 02:39:14PM +0200, Ludovic Desroches wrote:
> Hi Wenyou,
>
> On Mon, Oct 20, 2014 at 11:42:12AM +0800, Wenyou Yang wrote:
> > Drivers should put the device into low power states proactively whenever the
> > device is not in use. Thus implement support for runtime PM and use the
> > autosuspend feature to make sure that we can still perform well in case we see
> > lots of i2c traffic within short period of time.
> >
> > Signed-off-by: Wenyou Yang <wenyou.yang@...el.com>
> > ---
> > drivers/i2c/busses/i2c-at91.c | 48 ++++++++++++++++++++++++++++++++---------
> > 1 file changed, 38 insertions(+), 10 deletions(-)
> >
> > diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
> > index 917d545..03b9f48 100644
> > --- a/drivers/i2c/busses/i2c-at91.c
> > +++ b/drivers/i2c/busses/i2c-at91.c
> > @@ -31,10 +31,12 @@
> > #include <linux/platform_device.h>
> > #include <linux/slab.h>
> > #include <linux/platform_data/dma-atmel.h>
> > +#include <linux/pm_runtime.h>
> >
> > #define DEFAULT_TWI_CLK_HZ 100000 /* max 400 Kbits/s */
> > #define AT91_I2C_TIMEOUT msecs_to_jiffies(100) /* transfer timeout */
> > #define AT91_I2C_DMA_THRESHOLD 8 /* enable DMA if transfer size is bigger than this threshold */
> > +#define AUTOSUSPEND_TIMEOUT 2000
> >
> > /* AT91 TWI register definitions */
> > #define AT91_TWI_CR 0x0000 /* Control Register */
> > @@ -475,12 +477,16 @@ error:
> > static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
> > {
> > struct at91_twi_dev *dev = i2c_get_adapdata(adap);
> > - int ret;
> > + int ret = 0;
>
> Not necessary.
>
> > unsigned int_addr_flag = 0;
> > struct i2c_msg *m_start = msg;
> >
> > dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num);
> >
> > + ret = pm_runtime_get_sync(dev->dev);
> > + if (ret < 0)
> > + goto out;
> > +
> > /*
> > * The hardware can handle at most two messages concatenated by a
> > * repeated start via it's internal address feature.
> > @@ -488,18 +494,21 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
> > if (num > 2) {
> > dev_err(dev->dev,
> > "cannot handle more than two concatenated messages.\n");
> > - return 0;
> > + ret = 0;
> > + goto out;
> > } else if (num == 2) {
> > int internal_address = 0;
> > int i;
> >
> > if (msg->flags & I2C_M_RD) {
> > dev_err(dev->dev, "first transfer must be write.\n");
> > - return -EINVAL;
> > + ret = -EINVAL;
> > + goto out;
> > }
> > if (msg->len > 3) {
> > dev_err(dev->dev, "first message size must be <= 3.\n");
> > - return -EINVAL;
> > + ret = -EINVAL;
> > + goto out;
> > }
> >
> > /* 1st msg is put into the internal address, start with 2nd */
> > @@ -523,7 +532,13 @@ static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
> >
> > ret = at91_do_twi_transfer(dev);
> >
> > - return (ret < 0) ? ret : num;
> > + if (ret == 0)
>
> I don't figure out why you've changed this condition.
>
> > + ret = num;
> > +out:
> > + pm_runtime_mark_last_busy(dev->dev);
> > + pm_runtime_put_autosuspend(dev->dev);
> > +
> > + return ret;
> > }
> >
> > static u32 at91_twi_func(struct i2c_adapter *adapter)
> > @@ -795,11 +810,20 @@ static int at91_twi_probe(struct platform_device *pdev)
> > dev->adapter.timeout = AT91_I2C_TIMEOUT;
> > dev->adapter.dev.of_node = pdev->dev.of_node;
> >
> > + pm_runtime_set_autosuspend_delay(dev->dev, AUTOSUSPEND_TIMEOUT);
> > + pm_runtime_use_autosuspend(dev->dev);
> > + pm_runtime_set_active(dev->dev);
> > + pm_runtime_enable(dev->dev);
> > +
> > rc = i2c_add_numbered_adapter(&dev->adapter);
> > if (rc) {
> > dev_err(dev->dev, "Adapter %s registration failed\n",
> > dev->adapter.name);
> > clk_disable_unprepare(dev->clk);
> > +
> > + pm_runtime_disable(dev->dev);
> > + pm_runtime_set_suspended(dev->dev);
> > +
> > return rc;
> > }
> >
> > @@ -814,16 +838,19 @@ static int at91_twi_remove(struct platform_device *pdev)
> > i2c_del_adapter(&dev->adapter);
> > clk_disable_unprepare(dev->clk);
> >
> > + pm_runtime_disable(dev->dev);
> > + pm_runtime_set_suspended(dev->dev);
> > +
> > return 0;
> > }
> >
> > #ifdef CONFIG_PM
> > -
> > +#ifdef CONFIG_PM_RUNTIME
> > static int at91_twi_runtime_suspend(struct device *dev)
> > {
> > struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
> >
> > - clk_disable(twi_dev->clk);
> > + clk_disable_unprepare(twi_dev->clk);
> >
> > return 0;
> > }
> > @@ -832,12 +859,13 @@ static int at91_twi_runtime_resume(struct device *dev)
> > {
> > struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
> >
> > - return clk_enable(twi_dev->clk);
> > + return clk_prepare_enable(twi_dev->clk);
> > }
> > +#endif
> >
> > static const struct dev_pm_ops at91_twi_pm = {
> > - .runtime_suspend = at91_twi_runtime_suspend,
> > - .runtime_resume = at91_twi_runtime_resume,
> > + SET_RUNTIME_PM_OPS(at91_twi_runtime_suspend,
> > + at91_twi_runtime_resume, NULL)
> > };
> >
> > #define at91_twi_pm_ops (&at91_twi_pm)
> > --
> > 1.7.9.5
> >
>
>
> Regards
>
> Ludovic
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists