| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20141222125750.GA29163@anne>
Date: Mon, 22 Dec 2014 13:57:50 +0100
From: Evgeni Dobrev <evgeni@...dio-punkt.com>
To: devicetree@...r.kernel.org
Cc: linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
Jason Cooper <jason@...edaemon.net>,
Sebastian Hesselbarth <sebastian.hesselbarth@...glemail.com>,
Gregory Clement <gregory.clement@...e-electrons.com>,
Andrew Lunn <andrew@...n.ch>
Subject: [PATCH v3 1/1] add support for Seagate BlackArmor NAS220
This patch adds support for Seagate BlackArmor NAS220.
The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has
32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two
USB 2.0 ports, two buttons and three LEDs. There is a serial port available on
the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND).
The only functionality still not implemented is the bi-color led on the front
panel (status). Pins mpp22 and mpp23 control this led. Setting mpp22 to high and
mpp23 to low results in orange color. Setting mpp22 to low and mpp23 to high
results in blue color.
The third led is wired to show the SATA activity on the two drives.
Signed-off-by: Evgeni Dobrev <evgeni@...dio-punkt.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/kirkwood-nas220.dts | 166 +++++++++++++++++++++++++++++++++
2 files changed, 167 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-nas220.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 38c89ca..8b9ad1d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -132,6 +132,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
kirkwood-lsxhl.dtb \
kirkwood-mplcec4.dtb \
kirkwood-mv88f6281gtw-ge.dtb \
+ kirkwood-nas220.dtb \
kirkwood-net2big.dtb \
kirkwood-net5big.dtb \
kirkwood-netgear_readynas_duo_v2.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-nas220.dts b/arch/arm/boot/dts/kirkwood-nas220.dts
new file mode 100644
index 0000000..8175f3d
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-nas220.dts
@@ -0,0 +1,166 @@
+/*
+ * Device Tree file for Seagate BlackArmor NAS220
+ *
+ * Copyright (C) 2014 Evgeni Dobrev <evgeni@...dio-punkt.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+ model = "Seagate NAS 220";
+ compatible = "seagate,nas220","marvell,kirkwood-88f6192","marvell,kirkwood";
+
+ memory { /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+ };
+
+ ocp@...00000 {
+ pinctrl: pin-controller@...00 {
+ pinctrl-0 = <&pmx_uart0
+ &pmx_button_reset
+ &pmx_button_power>;
+ pinctrl-names = "default";
+
+ pmx_act_sata0: pmx-act-sata0 {
+ marvell,pins = "mpp15";
+ marvell,function = "sata0";
+ };
+ pmx_act_sata1: pmx-act-sata1 {
+ marvell,pins = "mpp16";
+ marvell,function = "sata1";
+ };
+ pmx_power_sata0: pmx-power-sata0 {
+ marvell,pins = "mpp24";
+ marvell,function = "gpio";
+ };
+ pmx_power_sata1: pmx-power-sata1 {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+ pmx_button_reset: pmx-button-reset {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_button_power: pmx-button-power {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+ };
+
+
+ /*
+ * Serial port routed to connector CN5
+ *
+ * pin 1 - TX
+ * pin 4 - RX
+ * pin 6 - GND
+ */
+ serial@...00 {
+ status = "okay";
+ };
+
+ sata@...00 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
+ i2c@...00 {
+ status = "okay";
+ adt7476: adt7476a@2e {
+ compatible = "adi,adt7476";
+ reg = <0x2e>;
+ };
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ button@1{
+ label = "Reset push button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ button@2{
+ label = "Power push button";
+ linux,code = <KEY_SLEEP>;
+ gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ blue-power {
+ label = "nas220:blue:power";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>;
+ pinctrl-names = "default";
+
+ sata0_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 24 0>;
+ };
+
+ sata1_power: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 28 0>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+ ethphy0: ethernet-phy@8 {
+ reg = <8>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists