| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20141223113128.GN32716@lunn.ch>
Date: Tue, 23 Dec 2014 12:31:28 +0100
From: Andrew Lunn <andrew@...n.ch>
To: Evgeni Dobrev <evgeni@...dio-punkt.com>
Cc: devicetree@...r.kernel.org, Jason Cooper <jason@...edaemon.net>,
Sebastian Hesselbarth <sebastian.hesselbarth@...glemail.com>,
linux-kernel@...r.kernel.org,
Gregory Clement <gregory.clement@...e-electrons.com>,
linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH v3 1/1] add support for Seagate BlackArmor NAS220
On Mon, Dec 22, 2014 at 01:57:50PM +0100, Evgeni Dobrev wrote:
> This patch adds support for Seagate BlackArmor NAS220.
>
> The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has
> 32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two
> USB 2.0 ports, two buttons and three LEDs. There is a serial port available on
> the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND).
>
> The only functionality still not implemented is the bi-color led on the front
> panel (status). Pins mpp22 and mpp23 control this led. Setting mpp22 to high and
> mpp23 to low results in orange color. Setting mpp22 to low and mpp23 to high
> results in blue color.
>
> The third led is wired to show the SATA activity on the two drives.
H Evgeni
This is looking good now. I will wait a few days to see if anybody
else has any comments, and it not, pull it into mvebu/dt.
Thanks
Andrew
>
> Signed-off-by: Evgeni Dobrev <evgeni@...dio-punkt.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/kirkwood-nas220.dts | 166 +++++++++++++++++++++++++++++++++
> 2 files changed, 167 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-nas220.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 38c89ca..8b9ad1d 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -132,6 +132,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
> kirkwood-lsxhl.dtb \
> kirkwood-mplcec4.dtb \
> kirkwood-mv88f6281gtw-ge.dtb \
> + kirkwood-nas220.dtb \
> kirkwood-net2big.dtb \
> kirkwood-net5big.dtb \
> kirkwood-netgear_readynas_duo_v2.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-nas220.dts b/arch/arm/boot/dts/kirkwood-nas220.dts
> new file mode 100644
> index 0000000..8175f3d
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-nas220.dts
> @@ -0,0 +1,166 @@
> +/*
> + * Device Tree file for Seagate BlackArmor NAS220
> + *
> + * Copyright (C) 2014 Evgeni Dobrev <evgeni@...dio-punkt.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6192.dtsi"
> +
> +/ {
> + model = "Seagate NAS 220";
> + compatible = "seagate,nas220","marvell,kirkwood-88f6192","marvell,kirkwood";
> +
> + memory { /* 128 MB */
> + device_type = "memory";
> + reg = <0x00000000 0x8000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + stdout-path = &uart0;
> + };
> +
> + ocp@...00000 {
> + pinctrl: pin-controller@...00 {
> + pinctrl-0 = <&pmx_uart0
> + &pmx_button_reset
> + &pmx_button_power>;
> + pinctrl-names = "default";
> +
> + pmx_act_sata0: pmx-act-sata0 {
> + marvell,pins = "mpp15";
> + marvell,function = "sata0";
> + };
> + pmx_act_sata1: pmx-act-sata1 {
> + marvell,pins = "mpp16";
> + marvell,function = "sata1";
> + };
> + pmx_power_sata0: pmx-power-sata0 {
> + marvell,pins = "mpp24";
> + marvell,function = "gpio";
> + };
> + pmx_power_sata1: pmx-power-sata1 {
> + marvell,pins = "mpp28";
> + marvell,function = "gpio";
> + };
> + pmx_button_reset: pmx-button-reset {
> + marvell,pins = "mpp29";
> + marvell,function = "gpio";
> + };
> + pmx_button_power: pmx-button-power {
> + marvell,pins = "mpp26";
> + marvell,function = "gpio";
> + };
> + };
> +
> +
> + /*
> + * Serial port routed to connector CN5
> + *
> + * pin 1 - TX
> + * pin 4 - RX
> + * pin 6 - GND
> + */
> + serial@...00 {
> + status = "okay";
> + };
> +
> + sata@...00 {
> + status = "okay";
> + nr-ports = <2>;
> + };
> +
> + i2c@...00 {
> + status = "okay";
> + adt7476: adt7476a@2e {
> + compatible = "adi,adt7476";
> + reg = <0x2e>;
> + };
> + };
> + };
> +
> + gpio_poweroff {
> + compatible = "gpio-poweroff";
> + gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + button@1{
> + label = "Reset push button";
> + linux,code = <KEY_POWER>;
> + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
> + };
> + button@2{
> + label = "Power push button";
> + linux,code = <KEY_SLEEP>;
> + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + blue-power {
> + label = "nas220:blue:power";
> + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>;
> + pinctrl-names = "default";
> +
> + sata0_power: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "SATA0 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 24 0>;
> + };
> +
> + sata1_power: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "SATA1 Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio0 28 0>;
> + };
> + };
> +};
> +
> +&nand {
> + status = "okay";
> +};
> +
> +&mdio {
> + status = "okay";
> + ethphy0: ethernet-phy@8 {
> + reg = <8>;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet0-port@0 {
> + phy-handle = <ðphy0>;
> + };
> +};
> --
> 1.7.10.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@...ts.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists