linux-kernel - Re: [PATCH v1 1/3] usb: dwc2: reset AHB hclk domain before init

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <55CD6078.8010502@rock-chips.com>
Date:	Fri, 14 Aug 2015 11:28:56 +0800
From:	Yunzhi Li <lyz@...k-chips.com>
To:	John Youn <John.Youn@...opsys.com>,
	"jwerner@...omium.org" <jwerner@...omium.org>,
	"dianders@...omium.org" <dianders@...omium.org>
CC:	"huangtao@...k-chips.com" <huangtao@...k-chips.com>,
	"cf@...k-chips.com" <cf@...k-chips.com>,
	"hl@...k-chips.com" <hl@...k-chips.com>,
	"wulf@...k-chips.com" <wulf@...k-chips.com>,
	"gregory.herrero@...el.com" <gregory.herrero@...el.com>,
	"linux-rockchip@...ts.infradead.org" 
	<linux-rockchip@...ts.infradead.org>,
	Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
	"linux-usb@...r.kernel.org" <linux-usb@...r.kernel.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v1 1/3] usb: dwc2: reset AHB hclk domain before init



在 2015/8/14 8:09, John Youn 写道:
> On 8/11/2015 12:57 AM, Yunzhi Li wrote:
>> We initiate dwc2 usb controller in BIOS, when kernel driver
>> start-up we should reset AHB hclk domain to reset all AHB
>> interface registers to default. Without this the FIFO value
>> setting might be incorrect because calculating FIFO size need the
>> power-on value of GRXFSIZ/GNPTXFSIZ/HPTXFSIZ registers.
>>
>> This patch could avoid warnning massage like in rk3288 platform:
>> [    2.074764] dwc2 ff580000.usb: 256 invalid for
>> host_perio_tx_fifo_size. Check HW configuration.
>>
>> ......
> I didn't receive the other two patches in this series so I was
> confused about where the "ahb_reset" was coming from when I
> replied to your other patch.
>
> I see you changed the name and documented the DT so never mind.
>
> Another thing is that there probably shouldn't be a debug
> message on the IS_ERR condition since that is the common case
> and of no interest to other platforms.
>
> The other two resets you added aren't used by the driver
> anywhere right? Maybe those should be left out until they are.
>
> John
>
Hi John ,

   Here is the other two patches :
     https://patchwork.kernel.org/patch/6989541/
     https://patchwork.kernel.org/patch/6989531/

   ahb_reset is hreset_n signal of dwc2 IP. Our rk3288 SoC implement 
connect this signal to a special
register in clock ang reset unit (CRU) module, set this register will 
reset dwc2 control and status registers(CSR)
to default value. You could find more info in <<DesignWare Cores USB 2.0 
Hi Speed On-TheGo (OTG) Databook 3.10a>>
4.4.1 System Clock and Reset Signals.

   Our problem is that dwc2_get_hwparams() reads fifo size registers and 
reguards it as the power-on reset value,
then dwc2_set_param_host_perio_tx_fifo_size() will check this value and 
make sure the new fifo size value is no bigger
than the power-on reset value. But we init and set these fifo registers 
in BIOS, so here hw->xxx_fifo_size is not the
real power-on reset vaule. So we hope to reset CSR before 
dwc2_get_hwparams().

I have another ideal: we might use GRSTCTL.CSftRst instead of hreset_n 
to reset dwc2 CSR.


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/