| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <5689FD36.4020609@westnet.com.au>
Date: Mon, 4 Jan 2016 15:03:50 +1000
From: Greg Ungerer <gregungerer@...tnet.com.au>
To: Linux/m68k <linux-m68k@...r.kernel.org>
Cc: Geert Uytterhoeven <geert@...ux-m68k.org>,
Frederik Völkel <frederik.voelkel@....de>,
Jiri Slaby <jslaby@...e.com>,
Greg KH <gregkh@...uxfoundation.org>,
"linux-serial@...r.kernel.org" <linux-serial@...r.kernel.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
linux-kernel@...cs.fau.de, Lukas Braun <lukas.braun@....de>,
uClinux development list <uclinux-dev@...inux.org>
Subject: Re: [PATCH] serial: Remove 68328 driver
If 68328serial.c is removed is there any point keeping the
architecture support for 68328 platforms?
The 68328serial.c provides pretty much the only type of console
that can be used on these devices. They are largely useless
without this.
Regards
Greg
On 19/12/15 00:27, Geert Uytterhoeven wrote:
> CC linux-m68k, uClinux-dev
>
> On Fri, Dec 18, 2015 at 12:28 PM, Frederik Völkel
> <frederik.voelkel@....de> wrote:
>> It's old, messy and mostly unmaintained.
>> Remove it as suggested by Peter Hurley and Alan.
>>
>> Signed-off-by: Frederik Völkel <frederik.voelkel@....de>
>> Signed-off-by: Lukas Braun <lukas.braun@....de>
>> ---
>> Should we remove other drivers like framebuffer as well?
>> It is probably useless without serial support.
>> ---
>> drivers/tty/serial/68328serial.c | 1322 --------------------------------------
>> drivers/tty/serial/Kconfig | 11 -
>> drivers/tty/serial/Makefile | 1 -
>> 3 files changed, 1334 deletions(-)
>> delete mode 100644 drivers/tty/serial/68328serial.c
>>
>> diff --git a/drivers/tty/serial/68328serial.c b/drivers/tty/serial/68328serial.c
>> deleted file mode 100644
>> index 0140ba4..0000000
>> --- a/drivers/tty/serial/68328serial.c
>> +++ /dev/null
>> @@ -1,1322 +0,0 @@
>> -/* 68328serial.c: Serial port driver for 68328 microcontroller
>> - *
>> - * Copyright (C) 1995 David S. Miller <davem@...p.rutgers.edu>
>> - * Copyright (C) 1998 Kenneth Albanowski <kjahds@...hds.com>
>> - * Copyright (C) 1998, 1999 D. Jeff Dionne <jeff@...inux.org>
>> - * Copyright (C) 1999 Vladimir Gurevich <vgurevic@...co.com>
>> - * Copyright (C) 2002-2003 David McCullough <davidm@...pgear.com>
>> - * Copyright (C) 2002 Greg Ungerer <gerg@...pgear.com>
>> - *
>> - * VZ Support/Fixes Evan Stawnyczy <e@...eo.ca>
>> - * Multiple UART support Daniel Potts <danielp@....unsw.edu.au>
>> - * Power management support Daniel Potts <danielp@....unsw.edu.au>
>> - * VZ Second Serial Port enable Phil Wilshire
>> - * 2.4/2.5 port David McCullough
>> - */
>> -
>> -#include <linux/module.h>
>> -#include <linux/errno.h>
>> -#include <linux/serial.h>
>> -#include <linux/signal.h>
>> -#include <linux/sched.h>
>> -#include <linux/timer.h>
>> -#include <linux/interrupt.h>
>> -#include <linux/tty.h>
>> -#include <linux/tty_flip.h>
>> -#include <linux/major.h>
>> -#include <linux/string.h>
>> -#include <linux/fcntl.h>
>> -#include <linux/mm.h>
>> -#include <linux/kernel.h>
>> -#include <linux/console.h>
>> -#include <linux/reboot.h>
>> -#include <linux/keyboard.h>
>> -#include <linux/init.h>
>> -#include <linux/pm.h>
>> -#include <linux/bitops.h>
>> -#include <linux/delay.h>
>> -#include <linux/gfp.h>
>> -
>> -#include <asm/io.h>
>> -#include <asm/irq.h>
>> -#include <asm/delay.h>
>> -#include <asm/uaccess.h>
>> -
>> -/* (es) */
>> -/* note: perhaps we can murge these files, so that you can just
>> - * define 1 of them, and they can sort that out for themselves
>> - */
>> -#if defined(CONFIG_M68EZ328)
>> -#include <asm/MC68EZ328.h>
>> -#else
>> -#if defined(CONFIG_M68VZ328)
>> -#include <asm/MC68VZ328.h>
>> -#else
>> -#include <asm/MC68328.h>
>> -#endif /* CONFIG_M68VZ328 */
>> -#endif /* CONFIG_M68EZ328 */
>> -
>> -/* Turn off usage of real serial interrupt code, to "support" Copilot */
>> -#ifdef CONFIG_XCOPILOT_BUGS
>> -#undef USE_INTS
>> -#else
>> -#define USE_INTS
>> -#endif
>> -
>> -/*
>> - * I believe this is the optimal setting that reduces the number of interrupts.
>> - * At high speeds the output might become a little "bursted" (use USTCNT_TXHE
>> - * if that bothers you), but in most cases it will not, since we try to
>> - * transmit characters every time rs_interrupt is called. Thus, quite often
>> - * you'll see that a receive interrupt occures before the transmit one.
>> - * -- Vladimir Gurevich
>> - */
>> -#define USTCNT_TX_INTR_MASK (USTCNT_TXEE)
>> -
>> -/*
>> - * 68328 and 68EZ328 UARTS are a little bit different. EZ328 has special
>> - * "Old data interrupt" which occures whenever the data stay in the FIFO
>> - * longer than 30 bits time. This allows us to use FIFO without compromising
>> - * latency. '328 does not have this feature and without the real 328-based
>> - * board I would assume that RXRE is the safest setting.
>> - *
>> - * For EZ328 I use RXHE (Half empty) interrupt to reduce the number of
>> - * interrupts. RXFE (receive queue full) causes the system to lose data
>> - * at least at 115200 baud
>> - *
>> - * If your board is busy doing other stuff, you might consider to use
>> - * RXRE (data ready intrrupt) instead.
>> - *
>> - * The other option is to make these INTR masks run-time configurable, so
>> - * that people can dynamically adapt them according to the current usage.
>> - * -- Vladimir Gurevich
>> - */
>> -
>> -/* (es) */
>> -#if defined(CONFIG_M68EZ328) || defined(CONFIG_M68VZ328)
>> -#define USTCNT_RX_INTR_MASK (USTCNT_RXHE | USTCNT_ODEN)
>> -#elif defined(CONFIG_M68328)
>> -#define USTCNT_RX_INTR_MASK (USTCNT_RXRE)
>> -#else
>> -#error Please, define the Rx interrupt events for your CPU
>> -#endif
>> -/* (/es) */
>> -
>> -/*
>> - * This is our internal structure for each serial port's state.
>> - */
>> -struct m68k_serial {
>> - struct tty_port tport;
>> - char is_cons; /* Is this our console. */
>> - int magic;
>> - int baud_base;
>> - int port;
>> - int irq;
>> - int type; /* UART type */
>> - int custom_divisor;
>> - int x_char; /* xon/xoff character */
>> - int line;
>> - unsigned char *xmit_buf;
>> - int xmit_head;
>> - int xmit_tail;
>> - int xmit_cnt;
>> -};
>> -
>> -#define SERIAL_MAGIC 0x5301
>> -
>> -/*
>> - * Define the number of ports supported and their irqs.
>> - */
>> -#define NR_PORTS 1
>> -
>> -static struct m68k_serial m68k_soft[NR_PORTS];
>> -
>> -static unsigned int uart_irqs[NR_PORTS] = { UART_IRQ_NUM };
>> -
>> -/* multiple ports are contiguous in memory */
>> -m68328_uart *uart_addr = (m68328_uart *)USTCNT_ADDR;
>> -
>> -struct tty_driver *serial_driver;
>> -
>> -static void change_speed(struct m68k_serial *info, struct tty_struct *tty);
>> -
>> -/*
>> - * Setup for console. Argument comes from the boot command line.
>> - */
>> -
>> -/* note: this is messy, but it works, again, perhaps defined somewhere else?*/
>> -#ifdef CONFIG_M68VZ328
>> -#define CONSOLE_BAUD_RATE 19200
>> -#define DEFAULT_CBAUD B19200
>> -#endif
>> -
>> -
>> -#ifndef CONSOLE_BAUD_RATE
>> -#define CONSOLE_BAUD_RATE 9600
>> -#define DEFAULT_CBAUD B9600
>> -#endif
>> -
>> -
>> -static int m68328_console_initted = 0;
>> -static int m68328_console_baud = CONSOLE_BAUD_RATE;
>> -static int m68328_console_cbaud = DEFAULT_CBAUD;
>> -
>> -
>> -static inline int serial_paranoia_check(struct m68k_serial *info,
>> - char *name, const char *routine)
>> -{
>> -#ifdef SERIAL_PARANOIA_CHECK
>> - static const char *badmagic =
>> - "Warning: bad magic number for serial struct %s in %s\n";
>> - static const char *badinfo =
>> - "Warning: null m68k_serial for %s in %s\n";
>> -
>> - if (!info) {
>> - printk(badinfo, name, routine);
>> - return 1;
>> - }
>> - if (info->magic != SERIAL_MAGIC) {
>> - printk(badmagic, name, routine);
>> - return 1;
>> - }
>> -#endif
>> - return 0;
>> -}
>> -
>> -/*
>> - * This is used to figure out the divisor speeds and the timeouts
>> - */
>> -static int baud_table[] = {
>> - 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
>> - 9600, 19200, 38400, 57600, 115200, 0 };
>> -
>> -/* Utility routines */
>> -static inline int get_baud(struct m68k_serial *ss)
>> -{
>> - unsigned long result = 115200;
>> - unsigned short int baud = uart_addr[ss->line].ubaud;
>> - if (GET_FIELD(baud, UBAUD_PRESCALER) == 0x38) result = 38400;
>> - result >>= GET_FIELD(baud, UBAUD_DIVIDE);
>> -
>> - return result;
>> -}
>> -
>> -/*
>> - * ------------------------------------------------------------
>> - * rs_stop() and rs_start()
>> - *
>> - * This routines are called before setting or resetting tty->stopped.
>> - * They enable or disable transmitter interrupts, as necessary.
>> - * ------------------------------------------------------------
>> - */
>> -static void rs_stop(struct tty_struct *tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned long flags;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_stop"))
>> - return;
>> -
>> - local_irq_save(flags);
>> - uart->ustcnt &= ~USTCNT_TXEN;
>> - local_irq_restore(flags);
>> -}
>> -
>> -static int rs_put_char(char ch)
>> -{
>> - unsigned long flags;
>> - int loops = 0;
>> -
>> - local_irq_save(flags);
>> -
>> - while (!(UTX & UTX_TX_AVAIL) && (loops < 1000)) {
>> - loops++;
>> - udelay(5);
>> - }
>> -
>> - UTX_TXDATA = ch;
>> - udelay(5);
>> - local_irq_restore(flags);
>> - return 1;
>> -}
>> -
>> -static void rs_start(struct tty_struct *tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned long flags;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_start"))
>> - return;
>> -
>> - local_irq_save(flags);
>> - if (info->xmit_cnt && info->xmit_buf && !(uart->ustcnt & USTCNT_TXEN)) {
>> -#ifdef USE_INTS
>> - uart->ustcnt |= USTCNT_TXEN | USTCNT_TX_INTR_MASK;
>> -#else
>> - uart->ustcnt |= USTCNT_TXEN;
>> -#endif
>> - }
>> - local_irq_restore(flags);
>> -}
>> -
>> -static void receive_chars(struct m68k_serial *info, unsigned short rx)
>> -{
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned char ch, flag;
>> -
>> - /*
>> - * This do { } while() loop will get ALL chars out of Rx FIFO
>> - */
>> -#ifndef CONFIG_XCOPILOT_BUGS
>> - do {
>> -#endif
>> - ch = GET_FIELD(rx, URX_RXDATA);
>> -
>> - if(info->is_cons) {
>> - if(URX_BREAK & rx) { /* whee, break received */
>> - return;
>> -#ifdef CONFIG_MAGIC_SYSRQ
>> - } else if (ch == 0x10) { /* ^P */
>> - show_state();
>> - show_free_areas(0);
>> - show_buffers();
>> -/* show_net_buffers(); */
>> - return;
>> - } else if (ch == 0x12) { /* ^R */
>> - emergency_restart();
>> - return;
>> -#endif /* CONFIG_MAGIC_SYSRQ */
>> - }
>> - }
>> -
>> - flag = TTY_NORMAL;
>> -
>> - if (rx & URX_PARITY_ERROR)
>> - flag = TTY_PARITY;
>> - else if (rx & URX_OVRUN)
>> - flag = TTY_OVERRUN;
>> - else if (rx & URX_FRAME_ERROR)
>> - flag = TTY_FRAME;
>> -
>> - tty_insert_flip_char(&info->tport, ch, flag);
>> -#ifndef CONFIG_XCOPILOT_BUGS
>> - } while((rx = uart->urx.w) & URX_DATA_READY);
>> -#endif
>> -
>> - tty_schedule_flip(&info->tport);
>> -}
>> -
>> -static void transmit_chars(struct m68k_serial *info, struct tty_struct *tty)
>> -{
>> - m68328_uart *uart = &uart_addr[info->line];
>> -
>> - if (info->x_char) {
>> - /* Send next char */
>> - uart->utx.b.txdata = info->x_char;
>> - info->x_char = 0;
>> - goto clear_and_return;
>> - }
>> -
>> - if ((info->xmit_cnt <= 0) || !tty || tty->stopped) {
>> - /* That's peculiar... TX ints off */
>> - uart->ustcnt &= ~USTCNT_TX_INTR_MASK;
>> - goto clear_and_return;
>> - }
>> -
>> - /* Send char */
>> - uart->utx.b.txdata = info->xmit_buf[info->xmit_tail++];
>> - info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
>> - info->xmit_cnt--;
>> -
>> - if(info->xmit_cnt <= 0) {
>> - /* All done for now... TX ints off */
>> - uart->ustcnt &= ~USTCNT_TX_INTR_MASK;
>> - goto clear_and_return;
>> - }
>> -
>> -clear_and_return:
>> - /* Clear interrupt (should be auto)*/
>> - return;
>> -}
>> -
>> -/*
>> - * This is the serial driver's generic interrupt routine
>> - */
>> -irqreturn_t rs_interrupt(int irq, void *dev_id)
>> -{
>> - struct m68k_serial *info = dev_id;
>> - struct tty_struct *tty = tty_port_tty_get(&info->tport);
>> - m68328_uart *uart;
>> - unsigned short rx;
>> - unsigned short tx;
>> -
>> - uart = &uart_addr[info->line];
>> - rx = uart->urx.w;
>> -
>> -#ifdef USE_INTS
>> - tx = uart->utx.w;
>> -
>> - if (rx & URX_DATA_READY)
>> - receive_chars(info, rx);
>> - if (tx & UTX_TX_AVAIL)
>> - transmit_chars(info, tty);
>> -#else
>> - receive_chars(info, rx);
>> -#endif
>> - tty_kref_put(tty);
>> -
>> - return IRQ_HANDLED;
>> -}
>> -
>> -static int startup(struct m68k_serial *info, struct tty_struct *tty)
>> -{
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned long flags;
>> -
>> - if (info->tport.flags & ASYNC_INITIALIZED)
>> - return 0;
>> -
>> - if (!info->xmit_buf) {
>> - info->xmit_buf = (unsigned char *) __get_free_page(GFP_KERNEL);
>> - if (!info->xmit_buf)
>> - return -ENOMEM;
>> - }
>> -
>> - local_irq_save(flags);
>> -
>> - /*
>> - * Clear the FIFO buffers and disable them
>> - * (they will be reenabled in change_speed())
>> - */
>> -
>> - uart->ustcnt = USTCNT_UEN;
>> - uart->ustcnt = USTCNT_UEN | USTCNT_RXEN | USTCNT_TXEN;
>> - (void)uart->urx.w;
>> -
>> - /*
>> - * Finally, enable sequencing and interrupts
>> - */
>> -#ifdef USE_INTS
>> - uart->ustcnt = USTCNT_UEN | USTCNT_RXEN |
>> - USTCNT_RX_INTR_MASK | USTCNT_TX_INTR_MASK;
>> -#else
>> - uart->ustcnt = USTCNT_UEN | USTCNT_RXEN | USTCNT_RX_INTR_MASK;
>> -#endif
>> -
>> - if (tty)
>> - clear_bit(TTY_IO_ERROR, &tty->flags);
>> - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
>> -
>> - /*
>> - * and set the speed of the serial port
>> - */
>> -
>> - change_speed(info, tty);
>> -
>> - info->tport.flags |= ASYNC_INITIALIZED;
>> - local_irq_restore(flags);
>> - return 0;
>> -}
>> -
>> -/*
>> - * This routine will shutdown a serial port; interrupts are disabled, and
>> - * DTR is dropped if the hangup on close termio flag is on.
>> - */
>> -static void shutdown(struct m68k_serial *info, struct tty_struct *tty)
>> -{
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned long flags;
>> -
>> - uart->ustcnt = 0; /* All off! */
>> - if (!(info->tport.flags & ASYNC_INITIALIZED))
>> - return;
>> -
>> - local_irq_save(flags);
>> -
>> - if (info->xmit_buf) {
>> - free_page((unsigned long) info->xmit_buf);
>> - info->xmit_buf = 0;
>> - }
>> -
>> - if (tty)
>> - set_bit(TTY_IO_ERROR, &tty->flags);
>> -
>> - info->tport.flags &= ~ASYNC_INITIALIZED;
>> - local_irq_restore(flags);
>> -}
>> -
>> -struct {
>> - int divisor, prescale;
>> -}
>> -#ifndef CONFIG_M68VZ328
>> - hw_baud_table[18] = {
>> - {0,0}, /* 0 */
>> - {0,0}, /* 50 */
>> - {0,0}, /* 75 */
>> - {0,0}, /* 110 */
>> - {0,0}, /* 134 */
>> - {0,0}, /* 150 */
>> - {0,0}, /* 200 */
>> - {7,0x26}, /* 300 */
>> - {6,0x26}, /* 600 */
>> - {5,0x26}, /* 1200 */
>> - {0,0}, /* 1800 */
>> - {4,0x26}, /* 2400 */
>> - {3,0x26}, /* 4800 */
>> - {2,0x26}, /* 9600 */
>> - {1,0x26}, /* 19200 */
>> - {0,0x26}, /* 38400 */
>> - {1,0x38}, /* 57600 */
>> - {0,0x38}, /* 115200 */
>> -};
>> -#else
>> - hw_baud_table[18] = {
>> - {0,0}, /* 0 */
>> - {0,0}, /* 50 */
>> - {0,0}, /* 75 */
>> - {0,0}, /* 110 */
>> - {0,0}, /* 134 */
>> - {0,0}, /* 150 */
>> - {0,0}, /* 200 */
>> - {0,0}, /* 300 */
>> - {7,0x26}, /* 600 */
>> - {6,0x26}, /* 1200 */
>> - {0,0}, /* 1800 */
>> - {5,0x26}, /* 2400 */
>> - {4,0x26}, /* 4800 */
>> - {3,0x26}, /* 9600 */
>> - {2,0x26}, /* 19200 */
>> - {1,0x26}, /* 38400 */
>> - {0,0x26}, /* 57600 */
>> - {1,0x38}, /* 115200 */
>> -};
>> -#endif
>> -/* rate = 1036800 / ((65 - prescale) * (1<<divider)) */
>> -
>> -/*
>> - * This routine is called to set the UART divisor registers to match
>> - * the specified baud rate for a serial port.
>> - */
>> -static void change_speed(struct m68k_serial *info, struct tty_struct *tty)
>> -{
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned short port;
>> - unsigned short ustcnt;
>> - unsigned cflag;
>> - int i;
>> -
>> - cflag = tty->termios.c_cflag;
>> - port = info->port;
>> - if (!port)
>> - return;
>> -
>> - ustcnt = uart->ustcnt;
>> - uart->ustcnt = ustcnt & ~USTCNT_TXEN;
>> -
>> - i = cflag & CBAUD;
>> - if (i & CBAUDEX) {
>> - i = (i & ~CBAUDEX) + B38400;
>> - }
>> -
>> - uart->ubaud = PUT_FIELD(UBAUD_DIVIDE, hw_baud_table[i].divisor) |
>> - PUT_FIELD(UBAUD_PRESCALER, hw_baud_table[i].prescale);
>> -
>> - ustcnt &= ~(USTCNT_PARITYEN | USTCNT_ODD_EVEN | USTCNT_STOP | USTCNT_8_7);
>> -
>> - if ((cflag & CSIZE) == CS8)
>> - ustcnt |= USTCNT_8_7;
>> -
>> - if (cflag & CSTOPB)
>> - ustcnt |= USTCNT_STOP;
>> -
>> - if (cflag & PARENB)
>> - ustcnt |= USTCNT_PARITYEN;
>> - if (cflag & PARODD)
>> - ustcnt |= USTCNT_ODD_EVEN;
>> -
>> -#ifdef CONFIG_SERIAL_68328_RTS_CTS
>> - if (cflag & CRTSCTS) {
>> - uart->utx.w &= ~ UTX_NOCTS;
>> - } else {
>> - uart->utx.w |= UTX_NOCTS;
>> - }
>> -#endif
>> -
>> - ustcnt |= USTCNT_TXEN;
>> -
>> - uart->ustcnt = ustcnt;
>> - return;
>> -}
>> -
>> -/*
>> - * Fair output driver allows a process to speak.
>> - */
>> -static void rs_fair_output(void)
>> -{
>> - int left; /* Output no more than that */
>> - unsigned long flags;
>> - struct m68k_serial *info = &m68k_soft[0];
>> - char c;
>> -
>> - if (info == NULL) return;
>> - if (info->xmit_buf == NULL) return;
>> -
>> - local_irq_save(flags);
>> - left = info->xmit_cnt;
>> - while (left != 0) {
>> - c = info->xmit_buf[info->xmit_tail];
>> - info->xmit_tail = (info->xmit_tail+1) & (SERIAL_XMIT_SIZE-1);
>> - info->xmit_cnt--;
>> - local_irq_restore(flags);
>> -
>> - rs_put_char(c);
>> -
>> - local_irq_save(flags);
>> - left = min(info->xmit_cnt, left-1);
>> - }
>> -
>> - /* Last character is being transmitted now (hopefully). */
>> - udelay(5);
>> -
>> - local_irq_restore(flags);
>> - return;
>> -}
>> -
>> -/*
>> - * m68k_console_print is registered for printk.
>> - */
>> -void console_print_68328(const char *p)
>> -{
>> - char c;
>> -
>> - while((c=*(p++)) != 0) {
>> - if(c == '\n')
>> - rs_put_char('\r');
>> - rs_put_char(c);
>> - }
>> -
>> - /* Comment this if you want to have a strict interrupt-driven output */
>> - rs_fair_output();
>> -
>> - return;
>> -}
>> -
>> -static void rs_set_ldisc(struct tty_struct *tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_set_ldisc"))
>> - return;
>> -
>> - info->is_cons = (tty->termios.c_line == N_TTY);
>> -
>> - printk("ttyS%d console mode %s\n", info->line, info->is_cons ? "on" : "off");
>> -}
>> -
>> -static void rs_flush_chars(struct tty_struct *tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned long flags;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_flush_chars"))
>> - return;
>> -#ifndef USE_INTS
>> - for(;;) {
>> -#endif
>> -
>> - /* Enable transmitter */
>> - local_irq_save(flags);
>> -
>> - if (info->xmit_cnt <= 0 || tty->stopped || !info->xmit_buf) {
>> - local_irq_restore(flags);
>> - return;
>> - }
>> -
>> -#ifdef USE_INTS
>> - uart->ustcnt |= USTCNT_TXEN | USTCNT_TX_INTR_MASK;
>> -#else
>> - uart->ustcnt |= USTCNT_TXEN;
>> -#endif
>> -
>> -#ifdef USE_INTS
>> - if (uart->utx.w & UTX_TX_AVAIL) {
>> -#else
>> - if (1) {
>> -#endif
>> - /* Send char */
>> - uart->utx.b.txdata = info->xmit_buf[info->xmit_tail++];
>> - info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
>> - info->xmit_cnt--;
>> - }
>> -
>> -#ifndef USE_INTS
>> - while (!(uart->utx.w & UTX_TX_AVAIL)) udelay(5);
>> - }
>> -#endif
>> - local_irq_restore(flags);
>> -}
>> -
>> -extern void console_printn(const char * b, int count);
>> -
>> -static int rs_write(struct tty_struct * tty,
>> - const unsigned char *buf, int count)
>> -{
>> - int c, total = 0;
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned long flags;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_write"))
>> - return 0;
>> -
>> - if (!tty || !info->xmit_buf)
>> - return 0;
>> -
>> - local_save_flags(flags);
>> - while (1) {
>> - local_irq_disable();
>> - c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
>> - SERIAL_XMIT_SIZE - info->xmit_head));
>> - local_irq_restore(flags);
>> -
>> - if (c <= 0)
>> - break;
>> -
>> - memcpy(info->xmit_buf + info->xmit_head, buf, c);
>> -
>> - local_irq_disable();
>> - info->xmit_head = (info->xmit_head + c) & (SERIAL_XMIT_SIZE-1);
>> - info->xmit_cnt += c;
>> - local_irq_restore(flags);
>> - buf += c;
>> - count -= c;
>> - total += c;
>> - }
>> -
>> - if (info->xmit_cnt && !tty->stopped) {
>> - /* Enable transmitter */
>> - local_irq_disable();
>> -#ifndef USE_INTS
>> - while(info->xmit_cnt) {
>> -#endif
>> -
>> - uart->ustcnt |= USTCNT_TXEN;
>> -#ifdef USE_INTS
>> - uart->ustcnt |= USTCNT_TX_INTR_MASK;
>> -#else
>> - while (!(uart->utx.w & UTX_TX_AVAIL)) udelay(5);
>> -#endif
>> - if (uart->utx.w & UTX_TX_AVAIL) {
>> - uart->utx.b.txdata = info->xmit_buf[info->xmit_tail++];
>> - info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
>> - info->xmit_cnt--;
>> - }
>> -
>> -#ifndef USE_INTS
>> - }
>> -#endif
>> - local_irq_restore(flags);
>> - }
>> -
>> - return total;
>> -}
>> -
>> -static int rs_write_room(struct tty_struct *tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> - int ret;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_write_room"))
>> - return 0;
>> - ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
>> - if (ret < 0)
>> - ret = 0;
>> - return ret;
>> -}
>> -
>> -static int rs_chars_in_buffer(struct tty_struct *tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer"))
>> - return 0;
>> - return info->xmit_cnt;
>> -}
>> -
>> -static void rs_flush_buffer(struct tty_struct *tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> - unsigned long flags;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_flush_buffer"))
>> - return;
>> - local_irq_save(flags);
>> - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
>> - local_irq_restore(flags);
>> - tty_wakeup(tty);
>> -}
>> -
>> -/*
>> - * ------------------------------------------------------------
>> - * rs_throttle()
>> - *
>> - * This routine is called by the upper-layer tty layer to signal that
>> - * incoming characters should be throttled.
>> - * ------------------------------------------------------------
>> - */
>> -static void rs_throttle(struct tty_struct * tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_throttle"))
>> - return;
>> -
>> - if (I_IXOFF(tty))
>> - info->x_char = STOP_CHAR(tty);
>> -
>> - /* Turn off RTS line (do this atomic) */
>> -}
>> -
>> -static void rs_unthrottle(struct tty_struct * tty)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_unthrottle"))
>> - return;
>> -
>> - if (I_IXOFF(tty)) {
>> - if (info->x_char)
>> - info->x_char = 0;
>> - else
>> - info->x_char = START_CHAR(tty);
>> - }
>> -
>> - /* Assert RTS line (do this atomic) */
>> -}
>> -
>> -/*
>> - * ------------------------------------------------------------
>> - * rs_ioctl() and friends
>> - * ------------------------------------------------------------
>> - */
>> -
>> -static int get_serial_info(struct m68k_serial * info,
>> - struct serial_struct * retinfo)
>> -{
>> - struct serial_struct tmp;
>> -
>> - if (!retinfo)
>> - return -EFAULT;
>> - memset(&tmp, 0, sizeof(tmp));
>> - tmp.type = info->type;
>> - tmp.line = info->line;
>> - tmp.port = info->port;
>> - tmp.irq = info->irq;
>> - tmp.flags = info->tport.flags;
>> - tmp.baud_base = info->baud_base;
>> - tmp.close_delay = info->tport.close_delay;
>> - tmp.closing_wait = info->tport.closing_wait;
>> - tmp.custom_divisor = info->custom_divisor;
>> - if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
>> - return -EFAULT;
>> -
>> - return 0;
>> -}
>> -
>> -static int set_serial_info(struct m68k_serial *info, struct tty_struct *tty,
>> - struct serial_struct * new_info)
>> -{
>> - struct tty_port *port = &info->tport;
>> - struct serial_struct new_serial;
>> - struct m68k_serial old_info;
>> - int retval = 0;
>> -
>> - if (!new_info)
>> - return -EFAULT;
>> - if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
>> - return -EFAULT;
>> - old_info = *info;
>> -
>> - if (!capable(CAP_SYS_ADMIN)) {
>> - if ((new_serial.baud_base != info->baud_base) ||
>> - (new_serial.type != info->type) ||
>> - (new_serial.close_delay != port->close_delay) ||
>> - ((new_serial.flags & ~ASYNC_USR_MASK) !=
>> - (port->flags & ~ASYNC_USR_MASK)))
>> - return -EPERM;
>> - port->flags = ((port->flags & ~ASYNC_USR_MASK) |
>> - (new_serial.flags & ASYNC_USR_MASK));
>> - info->custom_divisor = new_serial.custom_divisor;
>> - goto check_and_exit;
>> - }
>> -
>> - if (port->count > 1)
>> - return -EBUSY;
>> -
>> - /*
>> - * OK, past this point, all the error checking has been done.
>> - * At this point, we start making changes.....
>> - */
>> -
>> - info->baud_base = new_serial.baud_base;
>> - port->flags = ((port->flags & ~ASYNC_FLAGS) |
>> - (new_serial.flags & ASYNC_FLAGS));
>> - info->type = new_serial.type;
>> - port->close_delay = new_serial.close_delay;
>> - port->closing_wait = new_serial.closing_wait;
>> -
>> -check_and_exit:
>> - retval = startup(info, tty);
>> - return retval;
>> -}
>> -
>> -/*
>> - * get_lsr_info - get line status register info
>> - *
>> - * Purpose: Let user call ioctl() to get info when the UART physically
>> - * is emptied. On bus types like RS485, the transmitter must
>> - * release the bus after transmitting. This must be done when
>> - * the transmit shift register is empty, not be done when the
>> - * transmit holding register is empty. This functionality
>> - * allows an RS485 driver to be written in user space.
>> - */
>> -static int get_lsr_info(struct m68k_serial * info, unsigned int *value)
>> -{
>> -#ifdef CONFIG_SERIAL_68328_RTS_CTS
>> - m68328_uart *uart = &uart_addr[info->line];
>> -#endif
>> - unsigned char status;
>> - unsigned long flags;
>> -
>> - local_irq_save(flags);
>> -#ifdef CONFIG_SERIAL_68328_RTS_CTS
>> - status = (uart->utx.w & UTX_CTS_STAT) ? 1 : 0;
>> -#else
>> - status = 0;
>> -#endif
>> - local_irq_restore(flags);
>> - return put_user(status, value);
>> -}
>> -
>> -/*
>> - * This routine sends a break character out the serial port.
>> - */
>> -static void send_break(struct m68k_serial * info, unsigned int duration)
>> -{
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned long flags;
>> - if (!info->port)
>> - return;
>> - local_irq_save(flags);
>> -#ifdef USE_INTS
>> - uart->utx.w |= UTX_SEND_BREAK;
>> - msleep_interruptible(duration);
>> - uart->utx.w &= ~UTX_SEND_BREAK;
>> -#endif
>> - local_irq_restore(flags);
>> -}
>> -
>> -static int rs_ioctl(struct tty_struct *tty,
>> - unsigned int cmd, unsigned long arg)
>> -{
>> - struct m68k_serial * info = (struct m68k_serial *)tty->driver_data;
>> - int retval;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
>> - return -ENODEV;
>> -
>> - if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
>> - (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) &&
>> - (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
>> - if (tty->flags & (1 << TTY_IO_ERROR))
>> - return -EIO;
>> - }
>> -
>> - switch (cmd) {
>> - case TCSBRK: /* SVID version: non-zero arg --> no break */
>> - retval = tty_check_change(tty);
>> - if (retval)
>> - return retval;
>> - tty_wait_until_sent(tty, 0);
>> - if (!arg)
>> - send_break(info, 250); /* 1/4 second */
>> - return 0;
>> - case TCSBRKP: /* support for POSIX tcsendbreak() */
>> - retval = tty_check_change(tty);
>> - if (retval)
>> - return retval;
>> - tty_wait_until_sent(tty, 0);
>> - send_break(info, arg ? arg*(100) : 250);
>> - return 0;
>> - case TIOCGSERIAL:
>> - return get_serial_info(info,
>> - (struct serial_struct *) arg);
>> - case TIOCSSERIAL:
>> - return set_serial_info(info, tty,
>> - (struct serial_struct *) arg);
>> - case TIOCSERGETLSR: /* Get line status register */
>> - return get_lsr_info(info, (unsigned int *) arg);
>> - case TIOCSERGSTRUCT:
>> - if (copy_to_user((struct m68k_serial *) arg,
>> - info, sizeof(struct m68k_serial)))
>> - return -EFAULT;
>> - return 0;
>> - default:
>> - return -ENOIOCTLCMD;
>> - }
>> - return 0;
>> -}
>> -
>> -static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
>> -{
>> - struct m68k_serial *info = (struct m68k_serial *)tty->driver_data;
>> -
>> - change_speed(info, tty);
>> -
>> - if ((old_termios->c_cflag & CRTSCTS) &&
>> - !(tty->termios.c_cflag & CRTSCTS))
>> - rs_start(tty);
>> -
>> -}
>> -
>> -/*
>> - * ------------------------------------------------------------
>> - * rs_close()
>> - *
>> - * This routine is called when the serial port gets closed. First, we
>> - * wait for the last remaining data to be sent. Then, we unlink its
>> - * S structure from the interrupt chain if necessary, and we free
>> - * that IRQ if nothing is left in the chain.
>> - * ------------------------------------------------------------
>> - */
>> -static void rs_close(struct tty_struct *tty, struct file * filp)
>> -{
>> - struct m68k_serial * info = (struct m68k_serial *)tty->driver_data;
>> - struct tty_port *port = &info->tport;
>> - m68328_uart *uart = &uart_addr[info->line];
>> - unsigned long flags;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_close"))
>> - return;
>> -
>> - local_irq_save(flags);
>> -
>> - if (tty_hung_up_p(filp)) {
>> - local_irq_restore(flags);
>> - return;
>> - }
>> -
>> - if ((tty->count == 1) && (port->count != 1)) {
>> - /*
>> - * Uh, oh. tty->count is 1, which means that the tty
>> - * structure will be freed. Info->count should always
>> - * be one in these conditions. If it's greater than
>> - * one, we've got real problems, since it means the
>> - * serial port won't be shutdown.
>> - */
>> - printk("rs_close: bad serial port count; tty->count is 1, "
>> - "port->count is %d\n", port->count);
>> - port->count = 1;
>> - }
>> - if (--port->count < 0) {
>> - printk("rs_close: bad serial port count for ttyS%d: %d\n",
>> - info->line, port->count);
>> - port->count = 0;
>> - }
>> - if (port->count) {
>> - local_irq_restore(flags);
>> - return;
>> - }
>> - port->flags |= ASYNC_CLOSING;
>> - /*
>> - * Now we wait for the transmit buffer to clear; and we notify
>> - * the line discipline to only process XON/XOFF characters.
>> - */
>> - tty->closing = 1;
>> - if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE)
>> - tty_wait_until_sent(tty, port->closing_wait);
>> - /*
>> - * At this point we stop accepting input. To do this, we
>> - * disable the receive line status interrupts, and tell the
>> - * interrupt driver to stop checking the data ready bit in the
>> - * line status register.
>> - */
>> -
>> - uart->ustcnt &= ~USTCNT_RXEN;
>> - uart->ustcnt &= ~(USTCNT_RXEN | USTCNT_RX_INTR_MASK);
>> -
>> - shutdown(info, tty);
>> - rs_flush_buffer(tty);
>> -
>> - tty_ldisc_flush(tty);
>> - tty->closing = 0;
>> - tty_port_tty_set(&info->tport, NULL);
>> -#warning "This is not and has never been valid so fix it"
>> -#if 0
>> - if (tty->ldisc.num != ldiscs[N_TTY].num) {
>> - if (tty->ldisc.close)
>> - (tty->ldisc.close)(tty);
>> - tty->ldisc = ldiscs[N_TTY];
>> - tty->termios.c_line = N_TTY;
>> - if (tty->ldisc.open)
>> - (tty->ldisc.open)(tty);
>> - }
>> -#endif
>> - if (port->blocked_open) {
>> - if (port->close_delay)
>> - msleep_interruptible(jiffies_to_msecs(port->close_delay));
>> - wake_up_interruptible(&port->open_wait);
>> - }
>> - port->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
>> - local_irq_restore(flags);
>> -}
>> -
>> -/*
>> - * rs_hangup() --- called by tty_hangup() when a hangup is signaled.
>> - */
>> -void rs_hangup(struct tty_struct *tty)
>> -{
>> - struct m68k_serial * info = (struct m68k_serial *)tty->driver_data;
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_hangup"))
>> - return;
>> -
>> - rs_flush_buffer(tty);
>> - shutdown(info, tty);
>> - info->tport.count = 0;
>> - info->tport.flags &= ~ASYNC_NORMAL_ACTIVE;
>> - tty_port_tty_set(&info->tport, NULL);
>> - wake_up_interruptible(&info->tport.open_wait);
>> -}
>> -
>> -/*
>> - * This routine is called whenever a serial port is opened. It
>> - * enables interrupts for a serial port, linking in its S structure into
>> - * the IRQ chain. It also performs the serial-specific
>> - * initialization for the tty structure.
>> - */
>> -int rs_open(struct tty_struct *tty, struct file * filp)
>> -{
>> - struct m68k_serial *info;
>> - int retval;
>> -
>> - info = &m68k_soft[tty->index];
>> -
>> - if (serial_paranoia_check(info, tty->name, "rs_open"))
>> - return -ENODEV;
>> -
>> - info->tport.count++;
>> - tty->driver_data = info;
>> - tty_port_tty_set(&info->tport, tty);
>> -
>> - /*
>> - * Start up serial port
>> - */
>> - retval = startup(info, tty);
>> - if (retval)
>> - return retval;
>> -
>> - return tty_port_block_til_ready(&info->tport, tty, filp);
>> -}
>> -
>> -/* Finally, routines used to initialize the serial driver. */
>> -
>> -static void show_serial_version(void)
>> -{
>> - printk("MC68328 serial driver version 1.00\n");
>> -}
>> -
>> -static const struct tty_operations rs_ops = {
>> - .open = rs_open,
>> - .close = rs_close,
>> - .write = rs_write,
>> - .flush_chars = rs_flush_chars,
>> - .write_room = rs_write_room,
>> - .chars_in_buffer = rs_chars_in_buffer,
>> - .flush_buffer = rs_flush_buffer,
>> - .ioctl = rs_ioctl,
>> - .throttle = rs_throttle,
>> - .unthrottle = rs_unthrottle,
>> - .set_termios = rs_set_termios,
>> - .stop = rs_stop,
>> - .start = rs_start,
>> - .hangup = rs_hangup,
>> - .set_ldisc = rs_set_ldisc,
>> -};
>> -
>> -static const struct tty_port_operations rs_port_ops = {
>> -};
>> -
>> -/* rs_init inits the driver */
>> -static int __init
>> -rs68328_init(void)
>> -{
>> - unsigned long flags;
>> - int i;
>> - struct m68k_serial *info;
>> -
>> - serial_driver = alloc_tty_driver(NR_PORTS);
>> - if (!serial_driver)
>> - return -ENOMEM;
>> -
>> - show_serial_version();
>> -
>> - /* Initialize the tty_driver structure */
>> - /* SPARC: Not all of this is exactly right for us. */
>> -
>> - serial_driver->name = "ttyS";
>> - serial_driver->major = TTY_MAJOR;
>> - serial_driver->minor_start = 64;
>> - serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
>> - serial_driver->subtype = SERIAL_TYPE_NORMAL;
>> - serial_driver->init_termios = tty_std_termios;
>> - serial_driver->init_termios.c_cflag =
>> - m68328_console_cbaud | CS8 | CREAD | HUPCL | CLOCAL;
>> - serial_driver->flags = TTY_DRIVER_REAL_RAW;
>> - tty_set_operations(serial_driver, &rs_ops);
>> -
>> - local_irq_save(flags);
>> -
>> - for(i=0;i<NR_PORTS;i++) {
>> -
>> - info = &m68k_soft[i];
>> - tty_port_init(&info->tport);
>> - info->tport.ops = &rs_port_ops;
>> - info->magic = SERIAL_MAGIC;
>> - info->port = (int) &uart_addr[i];
>> - info->irq = uart_irqs[i];
>> - info->custom_divisor = 16;
>> - info->x_char = 0;
>> - info->line = i;
>> - info->is_cons = 1; /* Means shortcuts work */
>> -
>> - printk("%s%d at 0x%08x (irq = %d)", serial_driver->name, info->line,
>> - info->port, info->irq);
>> - printk(" is a builtin MC68328 UART\n");
>> -
>> -#ifdef CONFIG_M68VZ328
>> - if (i > 0 )
>> - PJSEL &= 0xCF; /* PSW enable second port output */
>> -#endif
>> -
>> - if (request_irq(uart_irqs[i],
>> - rs_interrupt,
>> - 0,
>> - "M68328_UART", info))
>> - panic("Unable to attach 68328 serial interrupt\n");
>> -
>> - tty_port_link_device(&info->tport, serial_driver, i);
>> - }
>> - local_irq_restore(flags);
>> -
>> - if (tty_register_driver(serial_driver)) {
>> - put_tty_driver(serial_driver);
>> - for (i = 0; i < NR_PORTS; i++)
>> - tty_port_destroy(&m68k_soft[i].tport);
>> - printk(KERN_ERR "Couldn't register serial driver\n");
>> - return -ENOMEM;
>> - }
>> -
>> - return 0;
>> -}
>> -
>> -module_init(rs68328_init);
>> -
>> -
>> -
>> -static void m68328_set_baud(void)
>> -{
>> - unsigned short ustcnt;
>> - int i;
>> -
>> - ustcnt = USTCNT;
>> - USTCNT = ustcnt & ~USTCNT_TXEN;
>> -
>> -again:
>> - for (i = 0; i < ARRAY_SIZE(baud_table); i++)
>> - if (baud_table[i] == m68328_console_baud)
>> - break;
>> - if (i >= ARRAY_SIZE(baud_table)) {
>> - m68328_console_baud = 9600;
>> - goto again;
>> - }
>> -
>> - UBAUD = PUT_FIELD(UBAUD_DIVIDE, hw_baud_table[i].divisor) |
>> - PUT_FIELD(UBAUD_PRESCALER, hw_baud_table[i].prescale);
>> - ustcnt &= ~(USTCNT_PARITYEN | USTCNT_ODD_EVEN | USTCNT_STOP | USTCNT_8_7);
>> - ustcnt |= USTCNT_8_7;
>> - ustcnt |= USTCNT_TXEN;
>> - USTCNT = ustcnt;
>> - m68328_console_initted = 1;
>> - return;
>> -}
>> -
>> -
>> -int m68328_console_setup(struct console *cp, char *arg)
>> -{
>> - int i, n = CONSOLE_BAUD_RATE;
>> -
>> - if (!cp)
>> - return(-1);
>> -
>> - if (arg)
>> - n = simple_strtoul(arg,NULL,0);
>> -
>> - for (i = 0; i < ARRAY_SIZE(baud_table); i++)
>> - if (baud_table[i] == n)
>> - break;
>> - if (i < ARRAY_SIZE(baud_table)) {
>> - m68328_console_baud = n;
>> - m68328_console_cbaud = 0;
>> - if (i > 15) {
>> - m68328_console_cbaud |= CBAUDEX;
>> - i -= 15;
>> - }
>> - m68328_console_cbaud |= i;
>> - }
>> -
>> - m68328_set_baud(); /* make sure baud rate changes */
>> - return(0);
>> -}
>> -
>> -
>> -static struct tty_driver *m68328_console_device(struct console *c, int *index)
>> -{
>> - *index = c->index;
>> - return serial_driver;
>> -}
>> -
>> -
>> -void m68328_console_write (struct console *co, const char *str,
>> - unsigned int count)
>> -{
>> - if (!m68328_console_initted)
>> - m68328_set_baud();
>> - while (count--) {
>> - if (*str == '\n')
>> - rs_put_char('\r');
>> - rs_put_char( *str++ );
>> - }
>> -}
>> -
>> -
>> -static struct console m68328_driver = {
>> - .name = "ttyS",
>> - .write = m68328_console_write,
>> - .device = m68328_console_device,
>> - .setup = m68328_console_setup,
>> - .flags = CON_PRINTBUFFER,
>> - .index = -1,
>> -};
>> -
>> -
>> -static int __init m68328_console_init(void)
>> -{
>> - register_console(&m68328_driver);
>> - return 0;
>> -}
>> -
>> -console_initcall(m68328_console_init);
>> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
>> index f38beb2..a261457 100644
>> --- a/drivers/tty/serial/Kconfig
>> +++ b/drivers/tty/serial/Kconfig
>> @@ -790,17 +790,6 @@ config SERIAL_CORE_CONSOLE
>> config CONSOLE_POLL
>> bool
>>
>> -config SERIAL_68328
>> - bool "68328 serial support"
>> - depends on M68328 || M68EZ328 || M68VZ328
>> - help
>> - This driver supports the built-in serial port of the Motorola 68328
>> - (standard, EZ and VZ varieties).
>> -
>> -config SERIAL_68328_RTS_CTS
>> - bool "Support RTS/CTS on 68328 serial port"
>> - depends on SERIAL_68328
>> -
>> config SERIAL_MCF
>> bool "Coldfire serial support"
>> depends on COLDFIRE
>> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
>> index 5ab4111..9d35387 100644
>> --- a/drivers/tty/serial/Makefile
>> +++ b/drivers/tty/serial/Makefile
>> @@ -34,7 +34,6 @@ obj-$(CONFIG_SERIAL_MAX3100) += max3100.o
>> obj-$(CONFIG_SERIAL_MAX310X) += max310x.o
>> obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o
>> obj-$(CONFIG_SERIAL_MUX) += mux.o
>> -obj-$(CONFIG_SERIAL_68328) += 68328serial.o
>> obj-$(CONFIG_SERIAL_MCF) += mcf.o
>> obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
>> obj-$(CONFIG_SERIAL_HS_LPC32XX) += lpc32xx_hs.o
>> --
>> 1.9.1
>
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@...ux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
> --
> To unsubscribe from this list: send the line "unsubscribe linux-m68k" in
> the body of a message to majordomo@...r.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists