[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Date: Mon, 10 Oct 2016 15:10:31 -0500
From: Rob Herring <robh@...nel.org>
To: Pantelis Antoniou <pantelis.antoniou@...sulko.com>
Cc: Lee Jones <lee.jones@...aro.org>,
Linus Walleij <linus.walleij@...aro.org>,
Alexandre Courbot <gnurou@...il.com>,
Mark Rutland <mark.rutland@....com>,
Frank Rowand <frowand.list@...il.com>,
Georgi Vlaev <gvlaev@...iper.net>,
Guenter Roeck <linux@...ck-us.net>,
JawaharBalaji Thirumalaisamy <jawaharb@...iper.net>,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-gpio@...r.kernel.org, linux-i2c@...r.kernel.org,
linux-mtd@...ts.infradead.org, linux-watchdog@...r.kernel.org,
netdev@...r.kernel.org
Subject: Re: [PATCH 2/4] mfd: ptxpmb-ext-cpld: Add documentation for PTXPMB
extended CPLD
On Fri, Oct 07, 2016 at 06:19:32PM +0300, Pantelis Antoniou wrote:
> From: Georgi Vlaev <gvlaev@...iper.net>
>
> Add DT bindings document for the PTXPMB extended CPLD device.
>
> Signed-off-by: Georgi Vlaev <gvlaev@...iper.net>
> [Ported from Juniper kernel]
> Signed-off-by: Pantelis Antoniou <pantelis.antoniou@...sulko.com>
> ---
> .../bindings/mfd/jnx-ptxpmb-ext-cpld.txt | 35 ++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/jnx-ptxpmb-ext-cpld.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/jnx-ptxpmb-ext-cpld.txt b/Documentation/devicetree/bindings/mfd/jnx-ptxpmb-ext-cpld.txt
> new file mode 100644
> index 0000000..098a548a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/jnx-ptxpmb-ext-cpld.txt
> @@ -0,0 +1,35 @@
> +* Device tree bindings for Juniper's PTXPMB Extended CPLD FPGA MFD driver
> +
> +The device supports a gpio block which is described in the
> +jnx-gpio-ptxpmb-ext-cpld document.
> +
> +Required properties:
> +
> +- compatible: "jnx,ptxpmb-ext-cpld"
> +
> +- reg: contains offset/length value for device state control
> + registers space.
> +
> +Optional properties:
> +
> +- interrupts: The interrupt line(s) the /IRQ signal(s) for the device is
> + connected to.
> +
> +- interrupt-parent: The parent interrupt controller.
> +
> +Example:
> +
> +ext-cpld@1,0 {
> + compatible = "jnx,ptxpmb-ext-cpld";
> + reg = <0x1 0 0x1000>;
What's the bus type here? Unit address is probably wrong.
> + interrupt-parent = <&mpic>;
> + interrupts = <7 2>, <8 2>;
> +
> + gpio_ext_cpld: cpld-ext-gpio {
> + compatible = "jnx,gpio-ptxpmb-ext-cpld";
> + #gpio-cells = <2>;
> + #interrupt-cells = <2>;
> + gpio-controller;
> + interrupt-controller;
> + };
> +};
> --
> 1.9.1
>
Powered by blists - more mailing lists