| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20161022140118.7a6cb583@bbrezillon>
Date: Sat, 22 Oct 2016 14:01:18 +0200
From: Boris Brezillon <boris.brezillon@...e-electrons.com>
To: Lukasz Majewski <l.majewski@...ess.pl>
Cc: Stefan Agner <stefan@...er.ch>, thierry.reding@...il.com,
mark.rutland@....com, linux-pwm@...r.kernel.org,
Bhuvanchandra DV <bhuvanchandra.dv@...adex.com>,
linux-kernel@...r.kernel.org, robh+dt@...nel.org,
kernel@...gutronix.de, fabio.estevam@....com, shawnguo@...nel.org,
linux-arm-kernel@...ts.infradead.org,
Lothar Wassmann <LW@...o-electronics.de>
Subject: Re: [PATCH v3 3/6] pwm: imx: support output polarity inversion
On Fri, 21 Oct 2016 23:49:39 +0200
Lukasz Majewski <l.majewski@...ess.pl> wrote:
> Hi Stefan,
>
> > On 2016-10-20 01:30, Lukasz Majewski wrote:
> > > Hi Stefan,
> > >
> > >> Hi Stefan,
> > >>
> > >> > On 2016-10-12 15:15, Lukasz Majewski wrote:
> > >> > > Hi Stefan,
> > >> > >
> > >> > >> On 2016-10-07 08:11, Bhuvanchandra DV wrote:
> > >> > >> > From: Lothar Wassmann <LW@...O-electronics.de>
> > >> > >> >
> > >> > >> > The i.MX pwm unit on i.MX27 and newer SoCs provides a
> > >> > >> > configurable output polarity. This patch adds support to
> > >> > >> > utilize this feature where available.
> > >> > >> >
> > >> > >> > Signed-off-by: Lothar Waßmann <LW@...O-electronics.de>
> > >> > >> > Signed-off-by: Lukasz Majewski <l.majewski@...sung.com>
> > >> > >> > Signed-off-by: Bhuvanchandra DV
> > >> > >> > <bhuvanchandra.dv@...adex.com> Acked-by: Shawn Guo
> > >> > >> > <shawn.guo@...aro.org> Reviewed-by: Sascha Hauer
> > >> > >> > <s.hauer@...gutronix.de> ---
> > >> > >> > Documentation/devicetree/bindings/pwm/imx-pwm.txt | 6 +--
> > >> > >> > drivers/pwm/pwm-imx.c | 51
> > >> > >> > +++++++++++++++++++++-- 2 files changed, 51 insertions(+), 6
> > >> > >> > deletions(-)
> > >> > >> >
> > >> > >> > diff --git
> > >> > >> > a/Documentation/devicetree/bindings/pwm/imx-pwm.txt
> > >> > >> > b/Documentation/devicetree/bindings/pwm/imx-pwm.txt index
> > >> > >> > e00c2e9..c61bdf8 100644 ---
> > >> > >> > a/Documentation/devicetree/bindings/pwm/imx-pwm.txt +++
> > >> > >> > b/Documentation/devicetree/bindings/pwm/imx-pwm.txt @@ -6,8
> > >> > >> > +6,8 @@ Required properties:
> > >> > >> > - "fsl,imx1-pwm" for PWM compatible with the one
> > >> > >> > integrated on i.MX1
> > >> > >> > - "fsl,imx27-pwm" for PWM compatible with the one
> > >> > >> > integrated on i.MX27
> > >> > >> > - reg: physical base address and length of the controller's
> > >> > >> > registers -- #pwm-cells: should be 2. See pwm.txt in this
> > >> > >> > directory for a description of
> > >> > >> > - the cells format.
> > >> > >> > +- #pwm-cells: 2 for i.MX1 and 3 for i.MX27 and newer SoCs.
> > >> > >> > See pwm.txt
> > >> > >> > + in this directory for a description of the cells format.
> > >> > >> > - clocks : Clock specifiers for both ipg and per clocks.
> > >> > >> > - clock-names : Clock names should include both "ipg" and
> > >> > >> > "per" See the clock consumer binding,
> > >> > >> > @@ -17,7 +17,7 @@ See the clock consumer binding,
> > >> > >> > Example:
> > >> > >> >
> > >> > >> > pwm1: pwm@...b4000 {
> > >> > >> > - #pwm-cells = <2>;
> > >> > >> > + #pwm-cells = <3>;
> > >> > >> > compatible = "fsl,imx53-pwm", "fsl,imx27-pwm";
> > >> > >> > reg = <0x53fb4000 0x4000>;
> > >> > >> > clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>,
> > >> > >> > diff --git a/drivers/pwm/pwm-imx.c b/drivers/pwm/pwm-imx.c
> > >> > >> > index d600fd5..c37d223 100644
> > >> > >> > --- a/drivers/pwm/pwm-imx.c
> > >> > >> > +++ b/drivers/pwm/pwm-imx.c
> > >> > >> > @@ -38,6 +38,7 @@
> > >> > >> > #define MX3_PWMCR_DOZEEN (1 << 24)
> > >> > >> > #define MX3_PWMCR_WAITEN (1 << 23)
> > >> > >> > #define MX3_PWMCR_DBGEN (1 << 22)
> > >> > >> > +#define MX3_PWMCR_POUTC (1 << 18)
> > >> > >> > #define MX3_PWMCR_CLKSRC_IPG_HIGH (2 << 16)
> > >> > >> > #define MX3_PWMCR_CLKSRC_IPG (1 << 16)
> > >> > >> > #define MX3_PWMCR_SWR (1 << 3)
> > >> > >> > @@ -180,6 +181,9 @@ static int imx_pwm_config_v2(struct
> > >> > >> > pwm_chip *chip, if (enable)
> > >> > >> > cr |= MX3_PWMCR_EN;
> > >> > >> >
> > >> > >> > + if (pwm->args.polarity == PWM_POLARITY_INVERSED)
> > >> > >> > + cr |= MX3_PWMCR_POUTC;
> > >> > >> > +
> > >> > >>
> > >> > >> This seems wrong to me, the config callback is meant for
> > >> > >> period/duty cycle only.
> > >
> > > Unfortunately, it also resets the PWM IP block and setups it again
> > > (by writing to PWMCR register). In that function we setup for
> > > example MX3_PWMCR_DOZEEN
> > > and MX3_PWMCR_DBGEN. Why cannot we setup polarity as well?
> > >
> > >
> > > I've double checked the backlight and pwm code flow.
> > >
> > > Please find following snippet:
> > >
> > > [ 0.135545] ######### imx_pwm_probe
> > > [ 0.135581] PWM supports output inversion
> > > [ 0.136864] ######### pwm_backlight_probe
> > > [ 0.136913] backlight supply power not found, using dummy
> > > regulator [ 0.136984] ######### imx_pwm_set_polarity 1
> > > [ 0.136995] imx_pwm_set_polarity: polarity set to inverted cr:
> > > 0x40000 0xf08f8000
> > > [ 0.137005] #########0 imx_pwm_config_v2 cr: 0x40000
> > > [ 0.137683] #########1 imx_pwm_config_v2 cr: 0x0 0xf08f8000
> > > [ 0.137693] #########2 imx_pwm_config_v2 cr: 0x1c20050
> > > [ 0.137702] #########3 imx_pwm_config_v2 cr: 0x1c20050 0xf08f8000
> > > [ 0.137711] @@@@@@@@@@ pwm_apply_state
>
> Maybe a bit more logs:
>
> [ 0.135451] ######### imx_pwm_probe
> [ 0.135488] PWM supports output inversion
> [ 0.136777] ######### pwm_backlight_probe
> [ 0.136826] backlight supply power not found, using dummy regulator
> [ 0.136893] ********* pwm_apply_state state->enabled: 0
> [ 0.136902] ######### imx_pwm_set_polarity 1
> [ 0.136913] imx_pwm_set_polarity: polarity set to inverted cr: 0x40000 0xf08f8000
> [ 0.136923] #########0 imx_pwm_config_v2 cr: 0x40000
> [ 0.137692] #########1 imx_pwm_config_v2 cr: 0x0 0xf08f8000
> [ 0.137701] #########2 imx_pwm_config_v2 cr: 0x1c20050
> [ 0.137710] #########3 imx_pwm_config_v2 cr: 0x1c20050 0xf08f8000
> [ 0.137720] @@@@@@@@@@ pwm_apply_state
> [ 0.137856] ********* pwm_apply_state state->enabled: 0
> [ 0.137869] #########0 imx_pwm_config_v2 cr: 0x1c20050
> [ 0.138904] #########1 imx_pwm_config_v2 cr: 0x0 0xf08f8000
> [ 0.138913] #########2 imx_pwm_config_v2 cr: 0x1c20050
> [ 0.138921] #########3 imx_pwm_config_v2 cr: 0x1c20050 0xf08f8000
> [ 0.138928] @@@@@@@@@@ pwm_apply_state
> [ 0.138940] ********* pwm_apply_state state->enabled: 1
> ^^^^^^^^^^^^^^^^^^ this is called from
> pwm_backlight_power_on() from pwm_bl probe function
>
> The problem here is not the lack of ->apply() callback, but the requirement to
> perform software reset on the pwm_v2 fifo when the pwm_v2 is NOT enabled (state->enabled: 0).
>
> As fair as I can see the pwm_state has following members: period, duty cycle, polarity and enabled.
> I'm fine to implement ->apply() callback, which would change above values.
>
> However, there is a problem with ->config() (imx_pwm_config_v2 @ pwm-imx.c) and imx pwm_v2 software
> FIFO reset.
> We can set polarity in any other kernel subsystem, which uses PWM (backlight in this example) and
> then this setting would disappear when we call pwm_apply_state with state->enabled = 0 (as presented
> in the log). This imposes setting polarity at ->config when we enable the PWM (as this patch does).
>
>
>
> > >
> > > Here the pwm_backlight_probe calls set_polarity callback available
> > > in pwm - the polarity is set (the 0x40000 value).
> > >
> > > The above operation is performed in pwm_apply_state (@
> > > drivers/pwm/core.c). In the same function, latter we call the
> > > pwm->chip->ops->config(), which is the pointer to config_v2.
> > > Since the PWM is not yet enabled, this function performs SW reset
> > > and PWM inversion setting is cleared.
> >
> > That function should not do that.
>
> I do agree that it shouldn't. Correct me if I'm wrong, but it seems like an
> PWM HW requirement to perform the reset.
>
> >It was probably already problematic
> > in the old times, it is definitely now with the atomic PWM stuff.
>
> The "atomic"[*] code (with ->apply() provided) will not solve this issue.
>
> >
> > >
> > > Possible solutions:
> > >
> > > 1. Leave the original patch from Bhuvanchandra as it was (I'm for
> > > this option)
> >
> > That really seems like a hack to me, and makes transition to the
> > atomic PWM API more complex.
>
> Could you be more specific here?
>
> As I mentioned before, the problem is not with the lack of
> "atomic" API.
Below is a quick and dirty I made on top of this patch to show you how
atomic update can be implemented in this driver. It's not tested, and
probably not working, but it should give you a better idea of what is
expected.
--->8---
>From f4dc9a368a951b619a9c67791cb9515ca70da0ee Mon Sep 17 00:00:00 2001
From: Boris Brezillon <boris.brezillon@...e-electrons.com>
Date: Sat, 22 Oct 2016 13:55:19 +0200
Subject: [PATCH] pwm: imx: switch to the atomic interface and related cleanup
This is just a crappy commit to show you how atomic update can be
implemented. Please do not submit the changes as is.
This commit is based on https://lkml.org/lkml/2016/10/7/454.
Signed-off-by: Boris Brezillon <boris.brezillon@...e-electrons.com>
---
drivers/pwm/pwm-imx.c | 262 +++++++++++++++++++++++---------------------------
1 file changed, 119 insertions(+), 143 deletions(-)
diff --git a/drivers/pwm/pwm-imx.c b/drivers/pwm/pwm-imx.c
index c37d22371848..c6d55f92dc40 100644
--- a/drivers/pwm/pwm-imx.c
+++ b/drivers/pwm/pwm-imx.c
@@ -66,8 +66,6 @@ struct imx_chip {
static int imx_pwm_config_v1(struct pwm_chip *chip,
struct pwm_device *pwm, int duty_ns, int period_ns)
{
- struct imx_chip *imx = to_imx_chip(chip);
-
/*
* The PWM subsystem allows for exact frequencies. However,
* I cannot connect a scope on my device to the PWM line and
@@ -85,81 +83,118 @@ static int imx_pwm_config_v1(struct pwm_chip *chip,
* both the prescaler (/1 .. /128) and then by CLKSEL
* (/2 .. /16).
*/
+ struct imx_chip *imx = to_imx_chip(chip);
u32 max = readl(imx->mmio_base + MX1_PWMP);
u32 p = max * duty_ns / period_ns;
+ int ret;
+
+ ret = clk_prepare_enable(imx->clk_ipg);
+ if (ret)
+ return ret;
+
writel(max - p, imx->mmio_base + MX1_PWMS);
+ clk_disable_unprepare(imx->clk_ipg);
+
return 0;
}
-static void imx_pwm_set_enable_v1(struct pwm_chip *chip, bool enable)
+static int imx_pwm_enable_v1(struct pwm_chip *chip, struct pwm_device *pwm)
{
struct imx_chip *imx = to_imx_chip(chip);
+ int ret;
u32 val;
+ ret = clk_prepare_enable(imx->clk_ipg);
+ if (ret)
+ return ret;
+
val = readl(imx->mmio_base + MX1_PWMC);
- if (enable)
- val |= MX1_PWMC_EN;
- else
- val &= ~MX1_PWMC_EN;
+ val |= MX1_PWMC_EN;
writel(val, imx->mmio_base + MX1_PWMC);
+
+ clk_disable_unprepare(imx->clk_per);
+
+ return 0;
}
-static int imx_pwm_config_v2(struct pwm_chip *chip,
- struct pwm_device *pwm, int duty_ns, int period_ns)
+static void imx_pwm_disable_v1(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct imx_chip *imx = to_imx_chip(chip);
+ u32 val;
+
+ val = readl(imx->mmio_base + MX1_PWMC);
+
+ val &= ~MX1_PWMC_EN;
+
+ writel(val, imx->mmio_base + MX1_PWMC);
+
+ clk_disable_unprepare(imx->clk_per);
+}
+
+static void imx_pwm_wait_fifo_slot(struct pwm_chip *chip, struct pwm_device *pwm)
{
struct imx_chip *imx = to_imx_chip(chip);
struct device *dev = chip->dev;
- unsigned long long c;
- unsigned long period_cycles, duty_cycles, prescale;
unsigned int period_ms;
- bool enable = pwm_is_enabled(pwm);
- int wait_count = 0, fifoav;
- u32 cr, sr;
+ int fifoav;
+ u32 sr;
+
+ sr = readl(imx->mmio_base + MX3_PWMSR);
+ fifoav = sr & MX3_PWMSR_FIFOAV_MASK;
+ if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+ period_ms = DIV_ROUND_UP(pwm_get_period(pwm),
+ NSEC_PER_MSEC);
+ msleep(period_ms);
- /*
- * i.MX PWMv2 has a 4-word sample FIFO.
- * In order to avoid FIFO overflow issue, we do software reset
- * to clear all sample FIFO if the controller is disabled or
- * wait for a full PWM cycle to get a relinquished FIFO slot
- * when the controller is enabled and the FIFO is fully loaded.
- */
- if (enable) {
sr = readl(imx->mmio_base + MX3_PWMSR);
- fifoav = sr & MX3_PWMSR_FIFOAV_MASK;
- if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
- period_ms = DIV_ROUND_UP(pwm_get_period(pwm),
- NSEC_PER_MSEC);
- msleep(period_ms);
-
- sr = readl(imx->mmio_base + MX3_PWMSR);
- if (fifoav == (sr & MX3_PWMSR_FIFOAV_MASK))
- dev_warn(dev, "there is no free FIFO slot\n");
- }
- } else {
- writel(MX3_PWMCR_SWR, imx->mmio_base + MX3_PWMCR);
- do {
- usleep_range(200, 1000);
- cr = readl(imx->mmio_base + MX3_PWMCR);
- } while ((cr & MX3_PWMCR_SWR) &&
- (wait_count++ < MX3_PWM_SWR_LOOP));
-
- if (cr & MX3_PWMCR_SWR)
- dev_warn(dev, "software reset timeout\n");
+ if (fifoav == (sr & MX3_PWMSR_FIFOAV_MASK))
+ dev_warn(dev, "there is no free FIFO slot\n");
}
+}
+
+static void imx_pwm_empty_fifo(struct pwm_chip *chip)
+{
+ struct imx_chip *imx = to_imx_chip(chip);
+ struct device *dev = chip->dev;
+ int wait_count = 0;
+ u32 cr;
+
+ writel(MX3_PWMCR_SWR, imx->mmio_base + MX3_PWMCR);
+ do {
+ usleep_range(200, 1000);
+ cr = readl(imx->mmio_base + MX3_PWMCR);
+ } while ((cr & MX3_PWMCR_SWR) &&
+ (wait_count++ < MX3_PWM_SWR_LOOP));
+
+ if (cr & MX3_PWMCR_SWR)
+ dev_warn(dev, "software reset timeout\n");
+}
+
+static int imx_pwm_apply_v2(struct pwm_chip *chip, struct pwm_device *pwm,
+ struct pwm_state *state)
+{
+ struct imx_chip *imx = to_imx_chip(chip);
+ unsigned long long c;
+ unsigned long period_cycles, duty_cycles, prescale;
+ struct pwm_state cstate;
+ int ret;
+ u32 cr = 0;
+
+ pwm_get_state(pwm, &cstate);
c = clk_get_rate(imx->clk_per);
- c = c * period_ns;
+ c = c * state->period;
do_div(c, 1000000000);
period_cycles = c;
prescale = period_cycles / 0x10000 + 1;
period_cycles /= prescale;
- c = (unsigned long long)period_cycles * duty_ns;
- do_div(c, period_ns);
+ c = (unsigned long long)period_cycles * state->duty_cycle;
+ do_div(c, state->period);
duty_cycles = c;
/*
@@ -171,134 +206,72 @@ static int imx_pwm_config_v2(struct pwm_chip *chip,
else
period_cycles = 0;
- writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
- writel(period_cycles, imx->mmio_base + MX3_PWMPR);
-
- cr = MX3_PWMCR_PRESCALER(prescale) |
- MX3_PWMCR_DOZEEN | MX3_PWMCR_WAITEN |
- MX3_PWMCR_DBGEN | MX3_PWMCR_CLKSRC_IPG_HIGH;
-
- if (enable)
- cr |= MX3_PWMCR_EN;
-
- if (pwm->args.polarity == PWM_POLARITY_INVERSED)
- cr |= MX3_PWMCR_POUTC;
-
- writel(cr, imx->mmio_base + MX3_PWMCR);
-
- return 0;
-}
-
-static void imx_pwm_set_enable_v2(struct pwm_chip *chip, bool enable)
-{
- struct imx_chip *imx = to_imx_chip(chip);
- u32 val;
-
- val = readl(imx->mmio_base + MX3_PWMCR);
-
- if (enable)
- val |= MX3_PWMCR_EN;
- else
- val &= ~MX3_PWMCR_EN;
-
- writel(val, imx->mmio_base + MX3_PWMCR);
-}
-
-static int imx_pwm_config(struct pwm_chip *chip,
- struct pwm_device *pwm, int duty_ns, int period_ns)
-{
- struct imx_chip *imx = to_imx_chip(chip);
- int ret;
-
- ret = clk_prepare_enable(imx->clk_ipg);
- if (ret)
- return ret;
-
- ret = imx->config(chip, pwm, duty_ns, period_ns);
-
- clk_disable_unprepare(imx->clk_ipg);
-
- return ret;
-}
-
-static int imx_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
-{
- struct imx_chip *imx = to_imx_chip(chip);
- int ret;
-
ret = clk_prepare_enable(imx->clk_per);
if (ret)
return ret;
- imx->set_enable(chip, true);
-
- return 0;
-}
+ /* Enable the clock if the PWM is being enabled. */
+ if (state->enabled && !cstate.enabled) {
+ ret = clk_prepare_enable(imx->clk_per);
+ if (ret)
+ return ret;
+ }
-static void imx_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
-{
- struct imx_chip *imx = to_imx_chip(chip);
+ /*
+ * Wait for a free FIFO slot if the PWM is already enabled, and flush
+ * the FIFO if the PWM was disabled and is about to be enabled.
+ */
+ if (cstate.enabled)
+ imx_pwm_wait_fifo_slot(chip, pwm);
+ else if (state->enabled)
+ imx_pwm_empty_fifo(chip);
- imx->set_enable(chip, false);
+ writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+ writel(period_cycles, imx->mmio_base + MX3_PWMPR);
- clk_disable_unprepare(imx->clk_per);
-}
+ cr |= MX3_PWMCR_PRESCALER(prescale) |
+ MX3_PWMCR_DOZEEN | MX3_PWMCR_WAITEN |
+ MX3_PWMCR_DBGEN | MX3_PWMCR_CLKSRC_IPG_HIGH;
-static int imx_pwm_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
- enum pwm_polarity polarity)
-{
- struct imx_chip *imx = to_imx_chip(chip);
- u32 val;
+ if (state->enabled)
+ cr |= MX3_PWMCR_EN;
- if (polarity == pwm->args.polarity)
- return 0;
+ if (state->polarity == PWM_POLARITY_INVERSED)
+ cr |= MX3_PWMCR_POUTC;
- val = readl(imx->mmio_base + MX3_PWMCR);
- if (polarity == PWM_POLARITY_INVERSED)
- val |= MX3_PWMCR_POUTC;
- else
- val &= ~MX3_PWMCR_POUTC;
+ writel(cr, imx->mmio_base + MX3_PWMCR);
- writel(val, imx->mmio_base + MX3_PWMCR);
+ /* Disable the clock if the PWM is being disabled. */
+ if (!state->enabled && cstate.enabled)
+ clk_disable_unprepare(imx->clk_per);
- dev_dbg(imx->chip.dev, "%s: polarity set to %s\n", __func__,
- polarity == PWM_POLARITY_INVERSED ? "inverted" : "normal");
+ clk_disable_unprepare(imx->clk_per);
return 0;
}
static struct pwm_ops imx_pwm_ops_v1 = {
- .enable = imx_pwm_enable,
- .disable = imx_pwm_disable,
- .config = imx_pwm_config,
+ .enable = imx_pwm_enable_v1,
+ .disable = imx_pwm_disable_v1,
+ .config = imx_pwm_config_v1,
.owner = THIS_MODULE,
};
static struct pwm_ops imx_pwm_ops_v2 = {
- .enable = imx_pwm_enable,
- .disable = imx_pwm_disable,
- .set_polarity = imx_pwm_set_polarity,
- .config = imx_pwm_config,
+ .apply = imx_pwm_apply_v2,
.owner = THIS_MODULE,
};
struct imx_pwm_data {
- int (*config)(struct pwm_chip *chip,
- struct pwm_device *pwm, int duty_ns, int period_ns);
- void (*set_enable)(struct pwm_chip *chip, bool enable);
struct pwm_ops *pwm_ops;
};
static struct imx_pwm_data imx_pwm_data_v1 = {
- .config = imx_pwm_config_v1,
- .set_enable = imx_pwm_set_enable_v1,
.pwm_ops = &imx_pwm_ops_v1,
};
static struct imx_pwm_data imx_pwm_data_v2 = {
- .config = imx_pwm_config_v2,
- .set_enable = imx_pwm_set_enable_v2,
.pwm_ops = &imx_pwm_ops_v2,
};
@@ -317,6 +290,7 @@ static int imx_pwm_probe(struct platform_device *pdev)
struct imx_chip *imx;
struct resource *r;
int ret = 0;
+ u32 cells;
if (!of_id)
return -ENODEV;
@@ -346,7 +320,12 @@ static int imx_pwm_probe(struct platform_device *pdev)
imx->chip.base = -1;
imx->chip.npwm = 1;
imx->chip.can_sleep = true;
- if (data->pwm_ops->set_polarity) {
+
+ ret = of_property_read_u32(pdev->dev.of_node, "#pwm-cells", &cells);
+ if (ret)
+ return ret;
+
+ if (cells == 3) {
dev_dbg(&pdev->dev, "PWM supports output inversion\n");
imx->chip.of_xlate = of_pwm_xlate_with_flags;
imx->chip.of_pwm_n_cells = 3;
@@ -357,9 +336,6 @@ static int imx_pwm_probe(struct platform_device *pdev)
if (IS_ERR(imx->mmio_base))
return PTR_ERR(imx->mmio_base);
- imx->config = data->config;
- imx->set_enable = data->set_enable;
-
ret = pwmchip_add(&imx->chip);
if (ret < 0)
return ret;
--
2.7.4
Powered by blists - more mailing lists