| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1494408696.31307.30.camel@mtkswgap22>
Date: Wed, 10 May 2017 17:31:36 +0800
From: Ryder Lee <ryder.lee@...iatek.com>
To: Matthias Brugger <matthias.bgg@...il.com>
CC: Bjorn Helgaas <bhelgaas@...gle.com>,
Rob Herring <robh+dt@...nel.org>,
Arnd Bergmann <arnd@...db.de>, <devicetree@...r.kernel.org>,
Red Hung <red.hung@...iatek.com>, <linux-pci@...r.kernel.org>,
<linux-kernel@...r.kernel.org>,
<linux-mediatek@...ts.infradead.org>,
<linux-arm-kernel@...ts.infradead.org>
Subject: Re: [PATCH v3 2/2] dt-bindings: pcie: Add documentation for
Mediatek PCIe
On Wed, 2017-05-10 at 09:58 +0200, Matthias Brugger wrote:
>
> On 10/05/17 04:07, Ryder Lee wrote:
> > Add documentation for PCIe host driver available in MT7623
> > series SoCs.
> >
> > Signed-off-by: Ryder Lee <ryder.lee@...iatek.com>
> > Acked-by: Rob Herring <robh@...nel.org>
> > ---
> > .../bindings/pci/mediatek,mt7623-pcie.txt | 149 +++++++++++++++++++++
> > 1 file changed, 149 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt
> >
> > diff --git a/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt
> > new file mode 100644
> > index 0000000..a9393ce
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt
> > @@ -0,0 +1,149 @@
> > +Mediatek Gen2 PCIe controller which is available on MT7623 series SoCs
> > +
> > +PCIe subsys supports single root complex (RC) with 3 Root Ports. Each root
> > +ports supports a Gen2 1-lane Link and has PIPE interface to PHY.
> > +
> > +Required properties:
> > +- compatible: Should contain "mediatek,mt7623-pcie".
> > +- device_type: Must be "pci"
> > +- reg: Base addresses and lengths of the PCIe controller.
> > +- #address-cells: Address representation for root ports (must be 3)
> > +- #size-cells: Size representation for root ports (must be 2)
> > +- #interrupt-cells: Size representation for interrupts (must be 1)
> > +- interrupts: Three interrupt outputs of the controller. Must contain an
> > + entry for each entry in the interrupt-names property.
> > +- interrupt-names: Must include the following names
> > + - "pcie-int0"
> > + - "pcie-int1"
> > + - "pcie-int2"
> > +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
> > + Please refer to the standard PCI bus binding document for a more detailed
> > + explanation.
> > +- clocks: Must contain an entry for each entry in clock-names.
> > + See ../clocks/clock-bindings.txt for details.
> > +- clock-names: Must include the following entries:
> > + - free_ck :for reference clock of PCIe subsys
> > + - sys_ck0 :for clock of Port0
> > + - sys_ck1 :for clock of Port1
> > + - sys_ck2 :for clock of Port2
> > +- resets: Must contain an entry for each entry in reset-names.
> > + See ../reset/reset.txt for details.
> > +- reset-names: Must include the following entries:
> > + - pcie-rst0 :port0 reset
> > + - pcie-rst1 :port1 reset
> > + - pcie-rst2 :port2 reset
> > +- phys: list of PHY specifiers (used by generic PHY framework).
> > +- phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
> > + number of PHYs as specified in *phys* property.
> > +- power-domains: A phandle and power domain specifier pair to the power domain
> > + which is responsible for collapsing and restoring power to the peripheral.
> > +- bus-range: Range of bus numbers associated with this controller.
> > +- ranges:
> > + - The first three entries are expected to translate the addresses for the root
> > + port registers, which are referenced by the assigned-addresses property of
> > + the root port nodes (see below).
> > + - The remaining entries setup the mapping for the standard I/O and memory
> > + regions.
> > + Please refer to the standard PCI bus binding document for a more detailed
> > + explanation.
> > +
> > +In addition, the device tree node must have sub-nodes describing each
> > +PCIe port interface, having the following mandatory properties:
> > +
> > +Required properties:
> > +- device_type: Must be "pci"
> > +- assigned-addresses: Address and size of the port configuration registers
> > +- reg: Only the first four bytes are used to refer to the correct bus number
> > + and device number.
> > +- #address-cells: Must be 3
> > +- #size-cells: Must be 2
> > +- #interrupt-cells: Must be 1
> > +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
> > + Please refer to the standard PCI bus binding document for a more detailed
> > + explanation.
> > +- ranges: Sub-ranges distributed from the PCIe controller node. An empty
> > + property is sufficient.
> > +- num-lanes: Number of lanes to use for this port.
> > +
> > +Examples:
> > +
> > + hifsys: syscon@...00000 {
> > + compatible = "mediatek,mt7623-hifsys", "syscon";
>
> If you want to put the clock controller subsystem node to the example,
> please use a valid compatible, for example:
>
> compatible = "mediatek,mt7623-hifsys",
> "mediatek,mt2701-hifsys",
> "syscon";
>
> Thanks,
> Matthias
OK i will correct it.
>
> > + reg = <0 0x1a000000 0 0x1000>;
> > + #clock-cells = <1>;
> > + #reset-cells = <1>;
> > + };
> > +
> > + pcie: pcie-controller@...40000 {
> > + compatible = "mediatek,mt7623-pcie";
> > + device_type = "pci";
> > + reg = <0 0x1a140000 0 0x1000>; /* PCIe shared registers */
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + #interrupt-cells = <1>;
> > + interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
> > + <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
> > + <GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
> > + interrupt-names = "pcie-int0", "pcie-int1", "pcie-int2";
> > + interrupt-map-mask = <0xf800 0 0 0>;
> > + interrupt-map = <0x0000 0 0 0 &gic GIC_SPI 193 IRQ_TYPE_NONE>,
> > + <0x0800 0 0 0 &gic GIC_SPI 194 IRQ_TYPE_NONE>,
> > + <0x1000 0 0 0 &gic GIC_SPI 195 IRQ_TYPE_NONE>;
> > + clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
> > + <&hifsys CLK_HIFSYS_PCIE0>,
> > + <&hifsys CLK_HIFSYS_PCIE1>,
> > + <&hifsys CLK_HIFSYS_PCIE2>;
> > + clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2";
> > + resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>,
> > + <&hifsys MT2701_HIFSYS_PCIE1_RST>,
> > + <&hifsys MT2701_HIFSYS_PCIE2_RST>;
> > + reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2";
> > + phys = <&pcie0_phy>, <&pcie1_phy>, <&pcie2_phy>;
> > + phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2";
> > + power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
> > + bus-range = <0x00 0xff>;
> > + ranges = <0x82000000 0 0x1a142000 0 0x1a142000 0 0x1000 /* Port0 registers */
> > + 0x82000000 0 0x1a143000 0 0x1a143000 0 0x1000 /* Port1 registers */
> > + 0x82000000 0 0x1a144000 0 0x1a144000 0 0x1000 /* Port2 registers */
> > + 0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000 /* I/O space */
> > + 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */
> > +
> > + pcie@0,0 {
> > + device_type = "pci";
> > + assigned-addresses = <0x82000000 0 0x1a142000 0 0x1000>;
> > + reg = <0x0000 0 0 0 0>;
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + #interrupt-cells = <1>;
> > + interrupt-map-mask = <0 0 0 0>;
> > + interrupt-map = <0 0 0 0 &gic GIC_SPI 193 IRQ_TYPE_NONE>;
> > + ranges;
> > + num-lanes = <1>;
> > + };
> > +
> > + pcie@1,0 {
> > + device_type = "pci";
> > + assigned-addresses = <0x82000800 0 0x1a143000 0 0x1000>;
> > + reg = <0x0800 0 0 0 0>;
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + #interrupt-cells = <1>;
> > + interrupt-map-mask = <0 0 0 0>;
> > + interrupt-map = <0 0 0 0 &gic GIC_SPI 194 IRQ_TYPE_NONE>;
> > + ranges;
> > + num-lanes = <1>;
> > + };
> > +
> > + pcie@2,0 {
> > + device_type = "pci";
> > + assigned-addresses = <0x82001000 0 0x1a144000 0 0x1000>;
> > + reg = <0x1000 0 0 0 0>;
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + #interrupt-cells = <1>;
> > + interrupt-map-mask = <0 0 0 0>;
> > + interrupt-map = <0 0 0 0 &gic GIC_SPI 195 IRQ_TYPE_NONE>;
> > + ranges;
> > + num-lanes = <1>;
> > + };
> > + };
> >
Powered by blists - more mailing lists