Message-ID: <d37dae42-77df-72b7-0898-a4873ccbbcce@arm.com>
Date:   Fri, 16 Jun 2017 10:35:28 +0100
From:   Marc Zyngier <marc.zyngier@....com>
To:     Jerome Brunet <jbrunet@...libre.com>,
        Jason Cooper <jason@...edaemon.net>,
        Thomas Gleixner <tglx@...utronix.de>,
        Kevin Hilman <khilman@...libre.com>
Cc:     Carlo Caione <carlo@...one.org>, linux-amlogic@...ts.infradead.org,
        linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org,
        Heiner Kallweit <hkallweit1@...il.com>
Subject: Re: [PATCH v3 2/6] irqchip: meson: add support for gpio interrupt
 controller

+ Heiner.

On 15/06/17 17:18, Jerome Brunet wrote:
> Add support for the interrupt gpio controller found on Amlogic's meson
> SoC family.
> 
> Unlike what the IP name suggest, it is not directly linked to the gpio
> subsystem. This separate controller is able to spy on the SoC pad. It is
> essentially a 256 to 8 router with a filtering block to select level or
> edge and polarity. The number of actual mappable inputs depends on the
> SoC.
> 
> Signed-off-by: Jerome Brunet <jbrunet@...libre.com>
> ---
>  drivers/irqchip/Kconfig          |   8 +
>  drivers/irqchip/Makefile         |   1 +
>  drivers/irqchip/irq-meson-gpio.c | 407 +++++++++++++++++++++++++++++++++++++++
>  3 files changed, 416 insertions(+)
>  create mode 100644 drivers/irqchip/irq-meson-gpio.c
> 
> diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
> index 478f8ace2664..be577a7512cc 100644
> --- a/drivers/irqchip/Kconfig
> +++ b/drivers/irqchip/Kconfig
> @@ -301,3 +301,11 @@ config QCOM_IRQ_COMBINER
>  	help
>  	  Say yes here to add support for the IRQ combiner devices embedded
>  	  in Qualcomm Technologies chips.
> +
> +config MESON_IRQ_GPIO
> +       bool "Meson GPIO Interrupt Multiplexer"
> +       depends on ARCH_MESON || COMPILE_TEST
> +       select IRQ_DOMAIN
> +       select IRQ_DOMAIN_HIERARCHY
> +       help
> +         Support Meson SoC Family GPIO Interrupt Multiplexer
> diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
> index b64c59b838a0..95bf2715850e 100644
> --- a/drivers/irqchip/Makefile
> +++ b/drivers/irqchip/Makefile
> @@ -76,3 +76,4 @@ obj-$(CONFIG_EZNPS_GIC)			+= irq-eznps.o
>  obj-$(CONFIG_ARCH_ASPEED)		+= irq-aspeed-vic.o
>  obj-$(CONFIG_STM32_EXTI) 		+= irq-stm32-exti.o
>  obj-$(CONFIG_QCOM_IRQ_COMBINER)		+= qcom-irq-combiner.o
> +obj-$(CONFIG_MESON_IRQ_GPIO)		+= irq-meson-gpio.o
> diff --git a/drivers/irqchip/irq-meson-gpio.c b/drivers/irqchip/irq-meson-gpio.c
> new file mode 100644
> index 000000000000..3b6d0ffec357
> --- /dev/null
> +++ b/drivers/irqchip/irq-meson-gpio.c
> @@ -0,0 +1,407 @@
> +/*
> + * Copyright (c) 2015 Endless Mobile, Inc.
> + * Author: Carlo Caione <carlo@...lessm.com>
> + * Copyright (c) 2016 BayLibre, SAS.
> + * Author: Jerome Brunet <jbrunet@...libre.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of version 2 of the GNU General Public License as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful, but
> + * WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
> + * General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, see <http://www.gnu.org/licenses/>.
> + * The full GNU General Public License is included in this distribution
> + * in the file called COPYING.
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/irq.h>
> +#include <linux/irqdomain.h>
> +#include <linux/irqchip.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +
> +#define NUM_UPSTREAM_IRQ 8
> +#define MAX_INPUT_MUX 256
> +
> +#define REG_EDGE_POL	0x00
> +#define REG_PIN_03_SEL	0x04
> +#define REG_PIN_47_SEL	0x08
> +#define REG_FILTER_SEL	0x0c
> +
> +#define REG_EDGE_POL_MASK(x)	(BIT(x) | BIT(16 + (x)))
> +#define REG_EDGE_POL_EDGE(x)	BIT(x)
> +#define REG_EDGE_POL_LOW(x)	BIT(16 + (x))
> +#define REG_PIN_SEL_SHIFT(x)	(((x) % 4) * 8)
> +#define REG_FILTER_SEL_SHIFT(x)	((x) * 4)
> +
> +struct meson_gpio_irq_params {
> +	unsigned int nr_hwirq;
> +};
> +
> +static const struct meson_gpio_irq_params meson8b_params = {
> +	.nr_hwirq = 119,
> +};
> +
> +static const struct meson_gpio_irq_params gxbb_params = {
> +	.nr_hwirq = 133,
> +};
> +
> +static const struct meson_gpio_irq_params gxl_params = {
> +	.nr_hwirq = 110,
> +};
> +
> +static const struct of_device_id meson_irq_gpio_matches[] = {
> +	{ .compatible = "amlogic,meson8b-gpio-intc", .data = &meson8b_params },
> +	{ .compatible = "amlogic,meson-gxbb-gpio-intc", .data = &gxbb_params },
> +	{ .compatible = "amlogic,meson-gxl-gpio-intc", .data = &gxl_params },
> +	{ }
> +};
> +
> +struct meson_gpio_irq_controller {
> +	unsigned int nr_hwirq;
> +	void __iomem *base;
> +	u32 upstream_irq[NUM_UPSTREAM_IRQ];
> +	DECLARE_BITMAP(map, NUM_UPSTREAM_IRQ);

upstream_irq doesn't mean much. You use "channel" elsewhere, which makes
a bit more sense (and map could become channel_map).

This NUM_UPSTREAM_IRQ could potentially become a SoC-specific parameter
(I wouldn't be surprised if a new SoC would have more of these).

> +	spinlock_t lock;
> +};
> +
> +static void meson_gpio_irq_update_bits(struct meson_gpio_irq_controller *ctl,
> +				       unsigned int reg, u32 mask, u32 val)
> +{
> +	u32 tmp;
> +
> +	tmp = readl_relaxed(ctl->base + reg);
> +	tmp &= ~mask;
> +	tmp |= val;
> +	writel_relaxed(tmp, ctl->base + reg);
> +}
> +
> +static int
> +meson_gpio_irq_request_channel(struct meson_gpio_irq_controller *ctl,
> +			       unsigned long  hwirq,
> +			       u32 **parent_hwirq)
> +{
> +	unsigned int reg, channel;
> +	unsigned long flags;
> +
> +	spin_lock_irqsave(&ctl->lock, flags);

You don't seem to take this spinlock in interrupt context. In that case,
you don't need to use the _irqsave version. Same thing for the set_type
callback.

> +
> +	/* Find a free channel */
> +	channel = find_first_zero_bit(ctl->map, NUM_UPSTREAM_IRQ);
> +	if (channel >= NUM_UPSTREAM_IRQ) {
> +		spin_unlock_irqrestore(&ctl->lock, flags);
> +		pr_err("No channel available\n");
> +		return -ENOSPC;
> +	}
> +
> +	/* Mark the channel as used */
> +	set_bit(channel, ctl->map);
> +
> +	/*
> +	 * Setup the mux of the channel to route the signal of the pad
> +	 * to the appropriate input of the GIC
> +	 */
> +	reg = (channel < 4) ? REG_PIN_03_SEL : REG_PIN_47_SEL;

Make a helper for this (channel_to_reg?).

> +	meson_gpio_irq_update_bits(ctl, reg,
> +				   0xff << REG_PIN_SEL_SHIFT(channel),
> +				   hwirq << REG_PIN_SEL_SHIFT(channel));
> +
> +	/* Get the parent hwirq number assigned to this channel */
> +	*parent_hwirq = &(ctl->upstream_irq[channel]);

A comment explaining how this simplifies the channel number computation
at runtime would be great, it took me a moment to understand how this works.

> +
> +	spin_unlock_irqrestore(&ctl->lock, flags);
> +
> +	pr_debug("hwirq %lu assigned to channel %d - parent %u\n",
> +		 hwirq, channel, **parent_hwirq);
> +
> +	return 0;
> +}
> +
> +static unsigned int
> +meson_gpio_irq_get_channel(struct meson_gpio_irq_controller *ctl,
> +			   u32 *parent_hwirq)
> +{
> +	return parent_hwirq - ctl->upstream_irq;
> +}
> +
> +static void
> +meson_gpio_irq_release_channel(struct meson_gpio_irq_controller *ctl,
> +			       u32 *parent_hwirq)
> +{
> +	unsigned int channel;
> +
> +	channel = meson_gpio_irq_get_channel(ctl, parent_hwirq);
> +	clear_bit(channel, ctl->map);
> +}
> +
> +static int meson_gpio_irq_type_setup(struct meson_gpio_irq_controller *ctl,
> +				     unsigned int type,
> +				     u32 *parent_hwirq)
> +{
> +	u32 val = 0;
> +	unsigned int channel;
> +	unsigned long flags;
> +
> +	channel = meson_gpio_irq_get_channel(ctl, parent_hwirq);
> +
> +	/*
> +	 * The controller has a filter block to operate in either LEVEL or
> +	 * EDGE mode, then signal is sent to the GIC. To enable LEVEL_LOW and
> +	 * EDGE_FALLING support (which the GIC does not support), the filter
> +	 * block is also able to invert the input signal it gets before
> +	 * providing it to the GIC.
> +	 */
> +	type &= IRQ_TYPE_SENSE_MASK;
> +
> +	if (type == IRQ_TYPE_EDGE_BOTH)
> +		return -EINVAL;
> +
> +	if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING))
> +		val |= REG_EDGE_POL_EDGE(channel);
> +
> +	if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_EDGE_FALLING))
> +		val |= REG_EDGE_POL_LOW(channel);
> +
> +	spin_lock_irqsave(&ctl->lock, flags);
> +
> +	meson_gpio_irq_update_bits(ctl, REG_EDGE_POL,
> +				   REG_EDGE_POL_MASK(channel), val);
> +
> +	spin_unlock_irqrestore(&ctl->lock, flags);
> +
> +	return 0;
> +}
> +
> +static unsigned int meson_gpio_irq_type_output(unsigned int type)
> +{
> +	unsigned int sense = type & IRQ_TYPE_SENSE_MASK;
> +
> +	type &= ~IRQ_TYPE_SENSE_MASK;
> +
> +	/*
> +	 * The polarity of the signal provided to the GIC should always
> +	 * be high.
> +	 */
> +	if (sense & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW))
> +		type |= IRQ_TYPE_LEVEL_HIGH;
> +	else if (sense & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING))
> +		type |= IRQ_TYPE_EDGE_RISING;
> +
> +	return type;
> +}
> +
> +static int meson_gpio_irq_set_type(struct irq_data *data, unsigned int type)
> +{
> +	struct meson_gpio_irq_controller *ctl = data->domain->host_data;
> +	u32 *parent_hwirq = irq_data_get_irq_chip_data(data);
> +	int ret;
> +
> +	ret = meson_gpio_irq_type_setup(ctl, type, parent_hwirq);
> +	if (ret)
> +		return ret;
> +
> +	return irq_chip_set_type_parent(data,
> +					meson_gpio_irq_type_output(type));
> +}
> +
> +static struct irq_chip meson_gpio_irq_chip = {
> +	.name			= "meson-gpio-irqchip",
> +	.irq_mask		= irq_chip_mask_parent,
> +	.irq_unmask		= irq_chip_unmask_parent,
> +	.irq_eoi		= irq_chip_eoi_parent,
> +	.irq_set_type		= meson_gpio_irq_set_type,
> +	.irq_retrigger		= irq_chip_retrigger_hierarchy,
> +#ifdef CONFIG_SMP
> +	.irq_set_affinity	= irq_chip_set_affinity_parent,
> +#endif
> +	.flags			= IRQCHIP_SET_TYPE_MASKED,
> +};
> +
> +static int meson_gpio_irq_domain_translate(struct irq_domain *domain,
> +					   struct irq_fwspec *fwspec,
> +					   unsigned long *hwirq,
> +					   unsigned int *type)
> +{
> +	if (is_of_node(fwspec->fwnode) && fwspec->param_count == 2) {
> +		*hwirq	= fwspec->param[0];
> +		*type	= fwspec->param[1];
> +		return 0;
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static int meson_gpio_irq_allocate_gic_irq(struct irq_domain *domain,
> +					   unsigned int virq,
> +					   u32 hwirq,
> +					   unsigned int type)
> +{
> +	struct irq_fwspec fwspec;
> +
> +	fwspec.fwnode = domain->parent->fwnode;
> +	fwspec.param_count = 3;
> +	fwspec.param[0] = 0;	/* SPI */
> +	fwspec.param[1] = hwirq;
> +	fwspec.param[2] = meson_gpio_irq_type_output(type);
> +
> +	return irq_domain_alloc_irqs_parent(domain, virq, 1, &fwspec);
> +}
> +
> +static int meson_gpio_irq_domain_alloc(struct irq_domain *domain,
> +				       unsigned int virq,
> +				       unsigned int nr_irqs,
> +				       void *data)
> +{
> +	struct irq_fwspec *fwspec = data;
> +	struct meson_gpio_irq_controller *ctl = domain->host_data;
> +	unsigned long hwirq;
> +	u32 *parent_hwirq;
> +	unsigned int type;
> +	int ret;
> +
> +	if (WARN_ON(nr_irqs != 1))
> +		return -EINVAL;
> +
> +	ret = meson_gpio_irq_domain_translate(domain, fwspec, &hwirq, &type);
> +	if (ret)
> +		return ret;
> +
> +	ret = meson_gpio_irq_request_channel(ctl, hwirq, &parent_hwirq);
> +	if (ret)
> +		return ret;
> +
> +	ret = meson_gpio_irq_allocate_gic_irq(domain, virq,
> +					      *parent_hwirq, type);
> +	if (ret < 0) {
> +		pr_err("failed to allocate gic irq %u\n", *parent_hwirq);

Release the requested channel?

> +		return ret;
> +	}
> +
> +	irq_domain_set_hwirq_and_chip(domain, virq, hwirq,
> +				      &meson_gpio_irq_chip, parent_hwirq);
> +
> +	return 0;
> +}
> +
> +static void meson_gpio_irq_domain_free(struct irq_domain *domain,
> +				       unsigned int virq,
> +				       unsigned int nr_irqs)
> +{
> +	struct meson_gpio_irq_controller *ctl = domain->host_data;
> +	struct irq_data *irq_data;
> +	u32 *parent_hwirq;
> +
> +	if (WARN_ON(nr_irqs != 1))
> +		return;
> +
> +	irq_domain_free_irqs_parent(domain, virq, 1);
> +
> +	irq_data = irq_domain_get_irq_data(domain, virq);
> +	parent_hwirq = irq_data_get_irq_chip_data(irq_data);
> +
> +	meson_gpio_irq_release_channel(ctl, parent_hwirq);
> +}
> +
> +static const struct irq_domain_ops meson_gpio_irq_domain_ops = {
> +	.alloc		= meson_gpio_irq_domain_alloc,
> +	.free		= meson_gpio_irq_domain_free,
> +	.translate	= meson_gpio_irq_domain_translate,
> +};
> +
> +static int __init meson_gpio_irq_parse_dt(struct device_node *node,
> +					  struct meson_gpio_irq_controller *ctl)
> +{
> +	const struct of_device_id *match;
> +	const struct meson_gpio_irq_params *params;
> +	int ret;
> +
> +	match = of_match_node(meson_irq_gpio_matches, node);
> +	if (!match)
> +		return -ENODEV;
> +
> +	params = match->data;
> +	ctl->nr_hwirq = params->nr_hwirq;
> +
> +	ret = of_property_read_variable_u32_array(node,
> +						  "amlogic,upstream-interrupts",
> +						  ctl->upstream_irq,
> +						  NUM_UPSTREAM_IRQ,
> +						  NUM_UPSTREAM_IRQ);
> +	if (ret < 0) {
> +		pr_err("can't get %d upstream interrupts\n", NUM_UPSTREAM_IRQ);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int __init meson_gpio_irq_of_init(struct device_node *node,
> +					 struct device_node *parent)
> +{
> +	struct irq_domain *domain, *parent_domain;
> +	struct meson_gpio_irq_controller *ctl;
> +	int ret;
> +
> +	if (!parent) {
> +		pr_err("missing parent interrupt node\n");
> +		return -ENODEV;
> +	}
> +
> +	parent_domain = irq_find_host(parent);
> +	if (!parent_domain) {
> +		pr_err("unable to obtain parent domain\n");
> +		return -ENXIO;
> +	}
> +
> +	ctl = kzalloc(sizeof(*ctl), GFP_KERNEL);
> +	if (!ctl)
> +		return -ENOMEM;
> +
> +	spin_lock_init(&ctl->lock);
> +
> +	ctl->base = of_iomap(node, 0);
> +	if (!ctl->base) {
> +		ret = -ENOMEM;
> +		goto free_ctl;
> +	}
> +
> +	bitmap_zero(ctl->map, NUM_UPSTREAM_IRQ);

The bitmap has already been cleared (kzalloc baby!).

> +
> +	ret = meson_gpio_irq_parse_dt(node, ctl);
> +	if (ret)
> +		goto free_upstream_irq;
> +
> +	domain = irq_domain_create_hierarchy(parent_domain, 0, ctl->nr_hwirq,
> +					     of_node_to_fwnode(node),
> +					     &meson_gpio_irq_domain_ops,
> +					     ctl);
> +	if (!domain) {
> +		pr_err("failed to add domain\n");
> +		ret = -ENODEV;
> +		goto free_upstream_irq;
> +	}
> +
> +	pr_info("%d to %d gpio interrupt mux initialized\n",
> +		ctl->nr_hwirq, NUM_UPSTREAM_IRQ);
> +
> +	return 0;
> +
> +free_upstream_irq:
> +	iounmap(ctl->base);
> +free_ctl:
> +	kfree(ctl);
> +
> +	return ret;
> +}
> +
> +IRQCHIP_DECLARE(meson_gpio_intc, "amlogic,meson-gpio-intc",
> +		meson_gpio_irq_of_init);
> 

Overall, this seems cleaner than Heiner's version (probably because it
is less ambitious). I'm looking forward to reviewing a series that will
be first agreed between both Heiner and you.

Thanks,

	M.
-- 
Jazz is not dead. It just smells funny...

Powered by blists - more mailing lists