| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1501049163-18892-3-git-send-email-xuejiancheng@hisilicon.com>
Date: Wed, 26 Jul 2017 14:06:01 +0800
From: Jiancheng Xue <xuejiancheng@...ilicon.com>
To: <robh+dt@...nel.org>, <kishon@...com>, <xuwei5@...ilicon.com>,
<catalin.marinas@....com>
CC: <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<hermit.wangheming@...ilicon.com>, <project-aspen-dev@...aro.org>,
Pengcheng Li <lpc.li@...ilicon.com>,
Jiancheng Xue <xuejiancheng@...ilicon.com>
Subject: [PATCH v2 2/4] phy: add inno-usb2-phy driver for hi3798cv200 SoC
From: Pengcheng Li <lpc.li@...ilicon.com>
Add inno-usb2-phy driver for hi3798cv200 SoC.
Signed-off-by: Pengcheng Li <lpc.li@...ilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@...ilicon.com>
---
drivers/phy/hisilicon/Kconfig | 11 +-
drivers/phy/hisilicon/Makefile | 1 +
drivers/phy/hisilicon/phy-hisi-inno-usb2.c | 236 +++++++++++++++++++++++++++++
3 files changed, 247 insertions(+), 1 deletion(-)
create mode 100644 drivers/phy/hisilicon/phy-hisi-inno-usb2.c
diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
index 6164c4c..6a675c5 100644
--- a/drivers/phy/hisilicon/Kconfig
+++ b/drivers/phy/hisilicon/Kconfig
@@ -8,9 +8,18 @@ config PHY_HI6220_USB
select MFD_SYSCON
help
Enable this to support the HISILICON HI6220 USB PHY.
-
To compile this driver as a module, choose M here.
+config PHY_HISI_INNO_USB2
+ tristate "HiSilicon INNO USB2 PHY support"
+ depends on (ARCH_HISI) || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Support for INNO USB2 PHY on HiSilicon SoCs. This Phy supports
+ USB 1.5Mb/s, USB 12Mb/s, USB 480Mb/s speeds. It supports one
+ USB host port to accept one USB device.
+
config PHY_HIX5HD2_SATA
tristate "HIX5HD2 SATA PHY Driver"
depends on ARCH_HIX5HD2 && OF && HAS_IOMEM
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
index 541b348..e6c9794 100644
--- a/drivers/phy/hisilicon/Makefile
+++ b/drivers/phy/hisilicon/Makefile
@@ -1,2 +1,3 @@
obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o
+obj-$(CONFIG_PHY_HISI_INNO_USB2) += phy-hisi-inno-usb2.o
obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
diff --git a/drivers/phy/hisilicon/phy-hisi-inno-usb2.c b/drivers/phy/hisilicon/phy-hisi-inno-usb2.c
new file mode 100644
index 0000000..7edf4a3
--- /dev/null
+++ b/drivers/phy/hisilicon/phy-hisi-inno-usb2.c
@@ -0,0 +1,236 @@
+/*
+ * HiSilicon INNO USB2 PHY Driver.
+ *
+ * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#define INNO_PHY_PORT_NUM 2
+#define REF_CLK_STABLE_TIME 100 /* unit:us */
+#define UTMI_CLK_STABLE_TIME 200 /* unit:us */
+#define TEST_CLK_STABLE_TIME 2 /* unit:ms */
+#define PHY_CLK_STABLE_TIME 2 /* unit:ms */
+#define UTMI_RST_COMPLETE_TIME 2 /* unit:ms */
+#define TEST_RST_COMPLETE_TIME 100 /* unit:us */
+#define POR_RST_COMPLETE_TIME 300 /* unit:us */
+#define PHY_TEST_DATA GENMASK(7, 0)
+#define PHY_TEST_ADDR GENMASK(15, 8)
+#define PHY_TEST_PORT GENMASK(18, 16)
+#define PHY_TEST_WREN BIT(21)
+#define PHY_TEST_CLK BIT(22) /* rising edge active */
+#define PHY_TEST_RST BIT(23) /* low active */
+#define PHY_CLK_ENABLE BIT(2)
+
+struct hisi_inno_phy_priv {
+ struct regmap *syscon;
+ u32 reg;
+ struct clk *ref_clk;
+ struct reset_control *por_rst;
+ struct reset_control *test_rst;
+ struct reset_control *utmi_rst[INNO_PHY_PORT_NUM];
+ u32 port_num;
+};
+
+static void hisi_inno_phy_write_reg(struct regmap *syscon,
+ u32 reg, u8 port, u32 addr, u32 data)
+{
+ u32 value;
+
+ value = (data & PHY_TEST_DATA)
+ | ((addr << 8) & PHY_TEST_ADDR)
+ | ((port << 16) & PHY_TEST_PORT)
+ | PHY_TEST_WREN | PHY_TEST_RST;
+ regmap_write(syscon, reg, value);
+ value |= PHY_TEST_CLK;
+ regmap_write(syscon, reg, value);
+ value &= ~PHY_TEST_CLK;
+ regmap_write(syscon, reg, value);
+}
+
+static void hisi_inno_phy_setup(struct hisi_inno_phy_priv *priv)
+{
+ /* The phy clk is controlled by the port0 register 0x06. */
+ hisi_inno_phy_write_reg(priv->syscon,
+ priv->reg, 0, 0x06, PHY_CLK_ENABLE);
+ msleep(PHY_CLK_STABLE_TIME);
+}
+
+static int hisi_inno_phy_init(struct phy *phy)
+{
+ struct hisi_inno_phy_priv *priv = phy_get_drvdata(phy);
+ int ret, i;
+
+ ret = clk_prepare_enable(priv->ref_clk);
+ if (ret)
+ return ret;
+ udelay(REF_CLK_STABLE_TIME);
+
+ if (priv->test_rst) {
+ reset_control_deassert(priv->test_rst);
+ udelay(TEST_RST_COMPLETE_TIME);
+ }
+
+ reset_control_deassert(priv->por_rst);
+ udelay(POR_RST_COMPLETE_TIME);
+
+ /* config phy clk and phy eye diagram */
+ hisi_inno_phy_setup(priv);
+
+ for (i = 0; i < priv->port_num; i++) {
+ reset_control_deassert(priv->utmi_rst[i]);
+ udelay(UTMI_RST_COMPLETE_TIME);
+ }
+
+ return 0;
+}
+
+static void hisi_inno_phy_disable(struct phy *phy)
+{
+ struct hisi_inno_phy_priv *priv = phy_get_drvdata(phy);
+ int i;
+
+ for (i = 0; i < priv->port_num; i++)
+ reset_control_assert(priv->utmi_rst[i]);
+
+ reset_control_assert(priv->por_rst);
+ if (priv->test_rst)
+ reset_control_assert(priv->test_rst);
+ clk_disable_unprepare(priv->ref_clk);
+}
+
+static int hisi_inno_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy *phy;
+ struct hisi_inno_phy_priv *priv;
+ struct device_node *node = dev->of_node;
+ int ret, i;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->syscon = syscon_regmap_lookup_by_phandle(node,
+ "hisilicon,peripheral-syscon");
+ if (IS_ERR(priv->syscon)) {
+ dev_err(dev, "no hisilicon,peripheral-syscon\n");
+ return PTR_ERR(priv->syscon);
+ }
+
+ ret = device_property_read_u32(dev,
+ "hisilicon,phycon-reg", &priv->reg);
+ if (ret)
+ return ret;
+
+ priv->ref_clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(priv->ref_clk))
+ return PTR_ERR(priv->ref_clk);
+
+ priv->por_rst = devm_reset_control_get_exclusive(dev, "power_on");
+ if (IS_ERR(priv->por_rst))
+ return PTR_ERR(priv->por_rst);
+
+ ret = device_property_read_u32(dev,
+ "hisilicon,port-num", &priv->port_num);
+ if (ret)
+ return ret;
+
+ if (priv->port_num <= 0
+ || priv->port_num > INNO_PHY_PORT_NUM)
+ return -EINVAL;
+
+ for (i = 0; i < priv->port_num; i++) {
+ char id[6];
+
+ snprintf(id, 6, "utmi%1d\n", i);
+ priv->utmi_rst[i] = devm_reset_control_get_exclusive(dev, id);
+ if (IS_ERR(priv->utmi_rst[i]))
+ return PTR_ERR(priv->utmi_rst[i]);
+ }
+
+ priv->test_rst = devm_reset_control_get_optional_exclusive(dev, "test");
+ if (IS_ERR(priv->test_rst))
+ return PTR_ERR(priv->test_rst);
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, phy);
+ phy_set_drvdata(phy, priv);
+
+ return hisi_inno_phy_init(phy);
+}
+
+static int hisi_inno_phy_remove(struct platform_device *pdev)
+{
+ struct phy *phy = platform_get_drvdata(pdev);
+
+ hisi_inno_phy_disable(phy);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int hisi_inno_phy_suspend(struct device *dev)
+{
+ struct phy *phy = dev_get_drvdata(dev);
+
+ hisi_inno_phy_disable(phy);
+
+ return 0;
+}
+
+static int hisi_inno_phy_resume(struct device *dev)
+{
+ struct phy *phy = dev_get_drvdata(dev);
+
+ return hisi_inno_phy_init(phy);
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static const struct dev_pm_ops hisi_inno_phy_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(hisi_inno_phy_suspend, hisi_inno_phy_resume)
+};
+
+static const struct of_device_id hisi_inno_phy_of_match[] = {
+ {.compatible = "hisilicon,inno-usb2-phy",},
+ {.compatible = "hisilicon,hi3798cv200-usb2-phy",},
+ { },
+};
+MODULE_DEVICE_TABLE(of, hisi_inno_phy_of_match);
+
+static struct platform_driver hisi_inno_phy_driver = {
+ .probe = hisi_inno_phy_probe,
+ .remove = hisi_inno_phy_remove,
+ .driver = {
+ .name = "hisi-inno-phy",
+ .of_match_table = hisi_inno_phy_of_match,
+ .pm = &hisi_inno_phy_pm_ops,
+ }
+};
+module_platform_driver(hisi_inno_phy_driver);
+
+MODULE_DESCRIPTION("HiSilicon INNO USB2 PHY Driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
Powered by blists - more mailing lists